 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... MC68HC908EY16 MC68HC908EY8 Data Sheet M68HC08 Microcontrollers MC68HC908EY16/D Rev. 7.0 5/2004 MOTOROLA.COM/SEMICONDUCTORS For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. MC68HC908EY16 MC68HC908EY8 Data Sheet Freescale Semiconductor, Inc... To provide the most up-to-date information, the revision of our documents on the World Wide Web will be the most current. Your printed copy may be an earlier revision. To verify you have the latest information available, refer to: http://motorola.com/semiconductors/ Refer to the Revision History for a summary of changes contained in this document. For your convenience, the page number designators have been linked to the appropriate location. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Data Sheet 3 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... Data Sheet 4 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 List of Sections Section 1. General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Section 2. Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Section 3. Analog-to-Digital Converter (ADC) Module . . . . . . . . . . . . 47 Section 4. BEMF Counter Module (BEMF) . . . . . . . . . . . . . . . . . . . . . . 61 Section 5. Configuration Registers (CONFIG1 and CONFIG2) . . . . . . 65 Section 6. Computer Operating Properly (COP) Module. . . . . . . . . . . 71 Section 7. Central Processor Unit (CPU) . . . . . . . . . . . . . . . . . . . . . . . 75 Section 8. Internal Clock Generator (ICG) Module. . . . . . . . . . . . . . . . 89 Section 9. External Interrupt (IRQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Section 10. Keyboard Interrupt (KBD) Module. . . . . . . . . . . . . . . . . . 125 Section 11. Low-Voltage Inhibit (LVI) Module . . . . . . . . . . . . . . . . . . 133 Section 12. Input/Output (I/O) Ports (PORTS) . . . . . . . . . . . . . . . . . . 137 Section 13. Enhanced Serial Communications Interface (ESCI) Module . . . . . . . . . . . . . . . . . . . . . . . . . 149 Section 14. System Integration Module (SIM) . . . . . . . . . . . . . . . . . . 185 Section 15. Serial Peripheral Interface (SPI) Module. . . . . . . . . . . . . 201 Section 16. Timebase Module (TBM). . . . . . . . . . . . . . . . . . . . . . . . . . 225 Section 17. Timer Interface A (TIMA) Module. . . . . . . . . . . . . . . . . . . 229 Section 18. Timer Interface B (TIMB) Module. . . . . . . . . . . . . . . . . . . 247 Section 19. Development Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 Section 20. Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . 283 Section 21. Ordering Information and Mechanical Specifications. . 295 Appendix A. MC68HC908EY8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311 Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA List of Sections Data Sheet 5 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. List of Sections Freescale Semiconductor, Inc... Data Sheet 6 List of Sections MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Table of Contents Section 1. General Description 1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 MCU Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Freescale Semiconductor, Inc... 1.2 1.3 1.4 1.5 1.5.1 1.5.2 1.5.3 1.5.4 1.5.5 Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Power Supply Pins (VDD and VSS) . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Oscillator Pins (PTC4/OSC1 and PTC3/OSC2) . . . . . . . . . . . . . . . . 23 External Reset Pin (RST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 External Interrupt Pin (IRQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Analog Power Supply/Reference Pins (VDDA, VREFH, VSSA and VREFL) . . . . . . . . . . . . . . . . . . . . . . . . . 23 1.5.6 Port A I/O Pins (PTA6/SS, PTA5/SPSCK, PTA4/KBD4-PTA0/KBD0). . . . . . . . . 24 1.5.7 Port B I/O Pins (PTB7/AD7/TBCH1, PTB6/AD6/TBCH0, PTB5/AD5-PTB0/AD0) 24 1.5.8 Port C I/O Pins (PTC4/OSC1, PTC3/OSC2, PTC2/MCLK, PTC1/MOSI, PTC0/MISO). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 1.5.9 Port D I/O Pins (PTD1/TACH1-PTD0/TACH0) . . . . . . . . . . . . . . . . 24 1.5.10 Port E I/O Pins (PTE1/RxD-PTE0/TxD) . . . . . . . . . . . . . . . . . . . . . . 25 Section 2. Memory 2.1 2.2 2.3 2.4 2.5 2.6 2.6.1 2.6.2 2.6.3 2.6.4 2.6.5 2.6.6 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Unimplemented Memory Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Reserved Memory Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Input/Output (I/O) Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Random Access Memory (RAM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 FLASH Memory (FLASH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FLASH Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FLASH Page Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FLASH Mass Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FLASH Program/Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . FLASH Block Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FLASH Block Protect Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 38 39 40 41 43 43 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Table of Contents Data Sheet 7 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Table of Contents 2.6.7 2.6.8 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Section 3. Analog-to-Digital Converter (ADC) Module 3.1 3.2 3.3 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.4 3.5 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADC Port I/O Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Voltage Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Conversion Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Continuous Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Result Justification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Monotonicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 49 49 50 50 51 51 Freescale Semiconductor, Inc... Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 3.6 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 3.6.1 ADC Analog Power Pin (VDDA). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 3.6.2 ADC Analog Ground Pin (VSSA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 3.6.3 ADC Voltage Reference Pin (VREFH) . . . . . . . . . . . . . . . . . . . . . . . . 53 3.6.4 ADC Voltage Reference Low Pin (VREFL) . . . . . . . . . . . . . . . . . . . . 53 3.6.5 ADC Voltage In (ADVIN). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 3.6.6 ADC External Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 3.6.6.1 VREFH and VREFL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 3.6.6.2 ANx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 3.6.6.3 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 3.7 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.1 ADC Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.2 ADC Data Register High (ADRH) and Data Register Low (ADRL). . 3.7.2.1 Left Justified Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.2.2 Right Justified Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.2.3 Left Justified Signed Data Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.2.4 Eight Bit Truncation Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7.3 ADC Clock Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 54 56 56 56 57 57 58 Section 4. BEMF Counter Module (BEMF) 4.1 4.2 4.3 4.4 4.5 4.5.1 4.5.2 Data Sheet 8 Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 BEMF Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Input Signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Table of Contents Section 5. Configuration Registers (CONFIG1 and CONFIG2) 5.1 5.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Section 6. Computer Operating Properly (COP) Module 6.1 6.2 6.3 6.3.1 6.3.2 6.3.3 6.3.4 6.3.5 6.3.6 6.3.7 6.3.8 6.4 6.5 6.6 6.7 6.7.1 6.7.2 6.8 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CGMXCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . STOP Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COPCTL Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internal Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset Vector Fetch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COPD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . COPRS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 72 72 72 72 72 73 73 73 Freescale Semiconductor, Inc... COP Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 COP Module During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Section 7. Central Processor Unit (CPU) 7.1 7.2 7.3 7.3.1 7.3.2 7.3.3 7.3.4 7.3.5 7.4 7.5 7.5.1 7.5.2 7.6 7.7 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stack Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Program Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Condition Code Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 76 77 77 78 78 Arithmetic/Logic Unit (ALU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Table of Contents Data Sheet 9 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Table of Contents 7.8 Opcode Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Section 8. Internal Clock Generator (ICG) Module 8.1 8.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Freescale Semiconductor, Inc... 8.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 8.3.1 Clock Enable Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 8.3.2 Internal Clock Generator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 8.3.2.1 Digitally Controlled Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 8.3.2.2 Modulo N Divider. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 8.3.2.3 Frequency Comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 8.3.2.4 Digital Loop Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 8.3.3 External Clock Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 8.3.3.1 External Oscillator Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 8.3.3.2 External Clock Input Path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 8.3.4 Clock Monitor Circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 8.3.4.1 Clock Monitor Reference Generator . . . . . . . . . . . . . . . . . . . . . . . 98 8.3.4.2 Internal Clock Activity Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 8.3.4.3 External Clock Activity Detector . . . . . . . . . . . . . . . . . . . . . . . . . 100 8.3.5 Clock Selection Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 8.3.5.1 Clock Selection Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 8.3.5.2 Clock Switching Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 8.4 Usage Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.1 Switching Clock Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.2 Enabling the Clock Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.3 Using Clock Monitor Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.4 Quantization Error in DCO Output . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.4.1 Digitally Controlled Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.4.2 Binary Weighted Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.4.3 Variable-Delay Ring Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.4.4 Ring Oscillator Fine-Adjust Circuit . . . . . . . . . . . . . . . . . . . . . . . 8.4.5 Switching Internal Clock Frequencies. . . . . . . . . . . . . . . . . . . . . . . 8.4.6 Nominal Frequency Settling Time. . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.6.1 Settling to Within 15 Percent. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.6.2 Settling to Within 5 Percent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.6.3 Total Settling Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.4.7 Trimming Frequency on the Internal Clock Generator . . . . . . . . . . 8.5 8.5.1 8.5.2 8.6 8.6.1 8.6.2 8.6.3 102 103 103 104 105 105 105 106 106 107 107 108 108 108 109 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 CONFIG Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Clock Enable (EXTCLKEN) . . . . . . . . . . . . . . . . . . . . . . . External Crystal Enable (EXTXTALEN) . . . . . . . . . . . . . . . . . . . . . Slow External Clock (EXTSLOW). . . . . . . . . . . . . . . . . . . . . . . . . . 110 111 111 111 Data Sheet 10 Table of Contents MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Table of Contents 8.6.4 8.7 8.7.1 8.7.2 8.7.3 8.7.4 8.7.5 Oscillator Enable In Stop (OSCENINSTOP). . . . . . . . . . . . . . . . . . 112 Input/Output (I/O) Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICG Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICG Multiplier Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICG Trim Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICG DCO Divider Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ICG DCO Stage Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 114 116 116 117 117 Section 9. External Interrupt (IRQ) 9.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 IRQ Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 IRQ Module During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 122 IRQ Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 9.2 9.3 9.4 9.5 9.6 Freescale Semiconductor, Inc... Section 10. Keyboard Interrupt (KBD) Module 10.1 10.2 10.3 10.4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Keyboard Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 10.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 10.5.1 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 10.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 10.6 Keyboard Module During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . 129 10.7 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129 10.7.1 Keyboard Status and Control Register . . . . . . . . . . . . . . . . . . . . . . 130 10.7.2 Keyboard Interrupt Enable Register . . . . . . . . . . . . . . . . . . . . . . . . 131 Section 11. Low-Voltage Inhibit (LVI) Module 11.1 11.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133 133 134 134 134 135 11.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3.1 Polled LVI Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3.2 Forced Reset Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3.3 False Reset Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3.4 LVI Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.4 11.5 LVI Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Data Sheet Table of Contents 11 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Table of Contents 11.5.1 11.5.2 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136 Section 12. Input/Output (I/O) Ports (PORTS) 12.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 12.2 Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 12.2.1 Port A Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138 12.2.2 Data Direction Register A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 12.3 Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 12.3.1 Port B Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140 12.3.2 Data Direction Register B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141 12.4 Port C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 12.4.1 Port C Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 12.4.2 Data Direction Register C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 12.5 Port D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 12.5.1 Port D Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 12.5.2 Data Direction Register D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 12.6 Port E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 12.6.1 Port E Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 12.6.2 Data Direction Register E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 Freescale Semiconductor, Inc... Section 13. Enhanced Serial Communications Interface (ESCI) Module 13.1 13.2 13.3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 151 154 154 154 154 156 156 157 157 157 157 157 159 160 161 163 163 164 13.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.1 Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2 Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.1 Character Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.2 Character Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.3 Break Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.4 Idle Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.5 Inversion of Transmitted Output . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.2.6 Transmitter Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3 Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.1 Character Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.2 Character Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.3 Data Sampling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.4 Framing Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.5 Baud Rate Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.6 Receiver Wakeup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.7 Receiver Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4.3.8 Error Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Sheet 12 Table of Contents MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Table of Contents 13.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 13.5.1 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 13.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164 13.6 ESCI During Break Module Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . 164 13.7 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 13.7.1 PTE0/TxD (Transmit Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 13.7.2 PTE1/RxD (Receive Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 13.8 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 13.8.1 ESCI Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166 13.8.2 ESCI Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 13.8.3 ESCI Control Register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 13.8.4 ESCI Status Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 13.8.5 ESCI Status Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174 13.8.6 ESCI Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 13.8.7 ESCI Baud Rate Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 13.8.8 ESCI Prescaler Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 176 13.9 ESCI Arbiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9.1 ESCI Arbiter Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9.2 ESCI Arbiter Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9.3 Bit Time Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9.4 Arbitration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180 180 181 181 183 Freescale Semiconductor, Inc... Section 14. System Integration Module (SIM) 14.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 187 187 187 187 188 188 189 189 190 190 190 191 191 191 191 191 191 14.2 SIM Bus Clock Control and Generation . . . . . . . . . . . . . . . . . . . . . . . . 14.2.1 Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.2.2 Clock Startup from POR or LVI Reset . . . . . . . . . . . . . . . . . . . . . . 14.2.3 Clocks in Stop Mode and Wait Mode . . . . . . . . . . . . . . . . . . . . . . . 14.3 Reset and System Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.1 External Pin Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2 Active Resets from Internal Sources . . . . . . . . . . . . . . . . . . . . . . . 14.3.2.1 Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2.2 Computer Operating Properly (COP) Reset . . . . . . . . . . . . . . . . 14.3.2.3 Illegal Opcode Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2.4 Illegal Address Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3.2.5 Forced Monitor Mode Entry Reset (MENRST) . . . . . . . . . . . . . . 14.3.2.6 Low-Voltage Inhibit (LVI) Reset . . . . . . . . . . . . . . . . . . . . . . . . . 14.4 SIM Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.4.1 SIM Counter During Power-On Reset . . . . . . . . . . . . . . . . . . . . . . 14.4.2 SIM Counter During Stop Mode Recovery . . . . . . . . . . . . . . . . . . . 14.4.3 SIM Counter and Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.5 Program Exception Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 14.5.1 Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Table of Contents Data Sheet 13 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Table of Contents 14.5.1.1 14.5.1.2 14.5.2 14.5.3 14.5.4 Hardware Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SWI Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status Flag Protection in Break Mode . . . . . . . . . . . . . . . . . . . . . . 194 195 195 195 195 14.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195 14.6.1 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 14.6.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 197 14.7 SIM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.7.1 SIM Break Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.7.2 SIM Reset Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.7.3 SIM Break Flag Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . 198 198 199 200 Freescale Semiconductor, Inc... Section 15. Serial Peripheral Interface (SPI) Module 15.1 15.2 15.3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201 Pin Name and Register Name Conventions . . . . . . . . . . . . . . . . . . . . . 201 15.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 203 15.4.1 Master Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 15.4.2 Slave Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 15.5 Transmission Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.5.1 Clock Phase and Polarity Controls . . . . . . . . . . . . . . . . . . . . . . . . . 15.5.2 Transmission Format When CPHA = 0. . . . . . . . . . . . . . . . . . . . . . 15.5.3 Transmission Format When CPHA = 1. . . . . . . . . . . . . . . . . . . . . . 15.5.4 Transmission Initiation Latency . . . . . . . . . . . . . . . . . . . . . . . . . . . 206 206 207 208 209 15.6 Error Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 15.6.1 Overflow Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 15.6.2 Mode Fault Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211 15.7 15.8 15.9 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213 Queuing Transmission Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214 Resetting the SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215 15.10 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 15.10.1 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 15.10.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 15.11 SPI During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216 15.12 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.12.1 MISO (Master In/Slave Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.12.2 MOSI (Master Out/Slave In) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.12.3 SPSCK (Serial Clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.12.4 SS (Slave Select) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.12.5 VSS (Clock Ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Sheet 14 Table of Contents 217 217 217 218 218 219 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Table of Contents 15.13 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.13.1 SPI Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.13.2 SPI Status and Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . 15.13.3 SPI Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219 219 221 224 Section 16. Timebase Module (TBM) 16.1 16.2 16.3 16.4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226 TBM Interrupt Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 Freescale Semiconductor, Inc... 16.5 16.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 16.6.1 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 16.6.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 227 16.7 Timebase Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Section 17. Timer Interface A (TIMA) Module 17.1 17.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229 229 232 232 233 233 234 234 235 236 237 17.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.1 TIMA Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.2 Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.3 Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.3.1 Unbuffered Output Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.3.2 Buffered Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.4 Pulse Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3.4.1 Unbuffered PWM Signal Generation. . . . . . . . . . . . . . . . . . . . . . 17.3.4.2 Buffered PWM Signal Generation . . . . . . . . . . . . . . . . . . . . . . . . 17.3.4.3 PWM Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.4 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 17.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 17.5.1 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 17.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 17.6 17.7 TIMA During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 238 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 239 239 239 241 242 242 246 17.8 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.8.1 TIMA Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . 17.8.2 TIMA Counter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.8.3 TIMA Counter Modulo Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 17.8.4 TIMA Channel Status and Control Registers . . . . . . . . . . . . . . . . . 17.8.5 TIMA Channel Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Table of Contents Data Sheet 15 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Table of Contents Section 18. Timer Interface B (TIMB) Module 18.1 18.2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 247 250 250 250 251 252 252 253 253 254 255 Freescale Semiconductor, Inc... 18.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.1 TIMB Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.2 Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.3 Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.3.1 Unbuffered Output Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.3.2 Buffered Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.4 Pulse Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3.4.1 Unbuffered PWM Signal Generation. . . . . . . . . . . . . . . . . . . . . . 18.3.4.2 Buffered PWM Signal Generation . . . . . . . . . . . . . . . . . . . . . . . . 18.3.4.3 PWM Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.4 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 18.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 18.5.1 Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 18.5.2 Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 18.6 TIMB During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256 18.7 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 18.7.1 TIMB Channel I/O Pins (PTB7/TBCH1-PTB6/TBCH0) . . . . . . . . . 257 18.8 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.8.1 TIMB Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . 18.8.2 TIMB Counter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.8.3 TIMB Counter Modulo Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 18.8.4 TIMB Channel Status and Control Registers . . . . . . . . . . . . . . . . . 18.8.5 TIMB Channel Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 257 257 259 260 260 264 Section 19. Development Support 19.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265 265 265 268 268 268 269 269 270 270 271 271 19.2 Break Module (BRK). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.1.1 Flag Protection During Break Interrupts . . . . . . . . . . . . . . . . . . . 19.2.1.2 TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.1.3 COP During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.2 Break Module Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.2.1 Break Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . 19.2.2.2 Break Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.2.3 Break Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.2.4 Break Flag Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2.3 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3 Monitor Module (MON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 19.3.1 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272 Data Sheet 16 Table of Contents MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Table of Contents 19.3.1.1 19.3.1.2 19.3.1.3 19.3.1.4 19.3.1.5 19.3.1.6 19.3.1.7 19.3.2 Normal Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Forced Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Monitor Vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Break Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 276 277 277 277 278 278 281 Section 20. Electrical Specifications 20.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283 Functional Operating Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284 Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286 Internal Oscillator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 External Oscillator Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287 Freescale Semiconductor, Inc... 20.2 20.3 20.4 20.5 20.6 20.7 20.8 20.9 Trimmed Accuracy of the Internal Clock Generator . . . . . . . . . . . . . . . 288 20.9.1 Trimmed Internal Clock Generator Characteristics. . . . . . . . . . . . . 288 20.10 Analog-to-Digital Converter (ADC) Characteristics. . . . . . . . . . . . . . . . 289 20.11 SPI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 20.12 Memory Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 Section 21. Ordering Information and Mechanical Specifications 21.1 21.2 21.3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 32-Pin QFP (Case Number 873) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 296 Appendix A. MC68HC908EY8 A.1 A.2 A.3 A.4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 Data Sheet -- Glossary Data Sheet -- Revision History MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Table of Contents Data Sheet 17 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Table of Contents Freescale Semiconductor, Inc... Data Sheet 18 Table of Contents MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 1. General Description 1.1 Introduction The MC68HC908EY16 is a member of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced M68HC08 central processor unit (CPU08) and are available with a variety of modules, memory sizes and types, and package types. The information contained in this document pertains to the MC68HC908EY8 with the exceptions noted in Appendix A. MC68HC908EY8. Freescale Semiconductor, Inc... 1.2 Features For convenience, features have been organized to reflect: * * Standard features of the MC68HC908EY16 Features of the CPU08 Standard features of the MC68HC908EY16 include: * * * * High-performance M68HC08 architecture optimized for C-compilers Fully upward-compatible object code with M6805, M146805, and M68HC05 Families 8-MHz internal bus frequency at 5V Internal oscillator requiring no external components: - Software selectable bus frequencies - 25 percent accuracy with a trimming capability of better than 1 percent - Clock monitor - Option to allow use of external clock source or external crystal/ceramic resonator 15,872 bytes of on-chip FLASH memory with in-circuit programming FLASH program memory security(1) 512 bytes of on-chip random-access memory (RAM) Low voltage inhibit (LVI) module Internal clock generator module (ICG) * * * * * 1. No security feature is absolutely secure. However, Motorola's strategy is to make reading or copying the FLASH difficult for unauthorized users. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA General Description Data Sheet 19 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. General Description * Two 16-bit, 2-channel timer (TIMA and TIMB) interface modules with selectable input capture, output compare, and pulse-width modulation (PWM) capability on each channel 8-channel, 10-bit successive approximation analog-to-digital converter (ADC) Enhanced serial communications interface module (ESCI) for local interconnect network (LIN) connectivity Serial peripheral interface (SPI) Timebase Module (TBM) 5-bit keyboard interrupt (KBI) with wakeup feature 24 general-purpose input/output (I/O) pins External asynchronous interrupt pin with internal pullup (IRQ) System protection features: - Optional computer operating properly (COP) reset - Illegal opcode detection with reset - Illegal address detection with reset 32-pin quad flat pack (QFP) package Low-power design; fully static with stop and wait modes Internal pullups on IRQ and RST to reduce customer system cost Standard low-power modes of operation: - Wait mode - Stop mode Master reset pin (RST) and power-on reset (POR) BREAK module (BRK) to allow single breakpoint setting during in-circuit debugging Higher current source capability on nine port lines for LED drive (PTA6/SS, PTA5/SPSCK, PTA4/KBD4, PTA3/KBD3, PTA2/KBD2, PTA1/KBD1, PTA0/KBD0, PTC1/MOSI, and PTC0/MISO) * * * * * Freescale Semiconductor, Inc... * * * * * * * * * * Features of the CPU08 include: * Enhanced HC05 programming model * Extensive loop control functions * 16 addressing modes (eight more than the HC05) * 16-bit index register and stack pointer * Memory-to-memory data transfers * Fast 8 x 8 multiply instruction * Fast 16 / 8 divide instruction * Binary-coded decimal (BCD) instructions * Optimization for controller applications * Third party C language support Data Sheet 20 General Description MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. General Description MCU Block Diagram 1.3 MCU Block Diagram Figure 1-1 shows the structure of the MC68HC908EY16. INTERNAL BUS M68HC08 CPU CPU REGISTERS ARITHMETIC/LOGIC UNIT (ALU) SINGLE BREAKPOINT BREAK MODULE PORT A DDRA 5-BIT KEYBOARD INTERRUPT MODULE PTA6/SS PTA5/SPSCK PTA4/KBD4 PTA3/KBD3 PTA2/KBD2 PTA1/KBD1 2-CHANNEL TIMER INTERFACE MODULE A PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PORT B DDRB PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK PTC1/MOSI PTC0/MISO PTD1/TACH1 PTD0/TACH0 PTE1/RxD PTE0/TxD PORT C PORT E PORT D CONTROL AND STATUS REGISTERS 64 BYTES Freescale Semiconductor, Inc... USER FLASH 15,872 BYTES USER RAM 512 BYTES MONITOR ROM 310 BYTES FLASH PROGRAMMING (BURN-IN) ROM 1024 BYTES USER FLASH VECTOR SPACE 36 BYTES 2-CHANNEL TIMER INTERFACE MODULE B ENHANCED SERIAL COMMUNICATION INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE OSC2 OSC1 INTERNAL CLOCK GENERATOR MODULE SERIAL PERIPHERAL INTERFACE MODULE RST 24 INTERNAL SYSTEM INTEGRATION MODULE SINGLE EXTERNAL IRQ MODULE CONFIGURATION REGISTER MODULE PERIODIC WAKEUP TIMEBASE MODULE ARBITER MODULE PRESCALER MODULE IRQ VREFH VDDA VREFL VSSA VDD VSS DDRE DDRD DDRC 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE SECURITY MODULE POWER BEMF MODULE Figure 1-1. MCU Block Diagram MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA General Description Data Sheet 21 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. General Description 1.4 Pin Assignments Figure 1-2 shows the pin assignments for the MC68HC908EY16. 32 PTA3/KBD3 PTA4/KBD4 VREFH 31 30 29 28 27 26 PTA2/KBD2 1 PTA1/KBD1 2 3 4 5 6 7 8 25 VREFL 24 23 22 21 20 19 18 VDDA VSSA VDD VSS PTE1/RxD PTE0/TxD PTC0/MISO PTC1/MOSI PTA5/SPSCK PTA6/SS PTB0/AD0 IRQ Freescale Semiconductor, Inc... PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK 10 11 12 13 14 PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 RST PTD0/TACH0 15 9 Figure 1-2. Pin Assignments 1.5 Pin Functions Descriptions of the pin functions are provided here. 1.5.1 Power Supply Pins (VDD and VSS) VDD and VSS are the power supply and ground pins. The MCU operates from a single power supply. Fast signal transitions on MCU pins place high, short-duration current demands on the power supply. To prevent noise problems, take special care to provide power supply bypassing at the MCU as Figure 1-3 shows. Place the C1 bypass capacitor as close to the MCU as possible. Use a high-frequency-response ceramic capacitor for C1. C2 is an optional bulk current bypass capacitor for use in applications that require the port pins to source high current levels. Data Sheet 22 General Description MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com PTD1/TACH1 16 17 Freescale Semiconductor, Inc. General Description Pin Functions MCU VDD VSS C1 0.1 F + C2 Freescale Semiconductor, Inc... VDD Note: Component values shown represent typical applications. Figure 1-3. Power Supply Bypassing 1.5.2 Oscillator Pins (PTC4/OSC1 and PTC3/OSC2) The OSC1 and OSC2 pins are available through programming options in the configuration register. These pins then become the connections to an external clock source or crystal/ceramic resonator. When selecting PTC4 and PTC3 as I/O, OSC1 and OSC2 functions are not available. 1.5.3 External Reset Pin (RST) A logic 0 on the RST pin forces the MCU to a known startup state. RST is bidirectional, allowing a reset of the entire system. It is driven low when any internal reset source is asserted. This pin contains an internal pullup resistor that is always activated, even when the reset pin is pulled low. See Section 14. System Integration Module (SIM). 1.5.4 External Interrupt Pin (IRQ) IRQ is an asynchronous external interrupt pin. This pin contains an internal pullup resistor that is always activated, even when the IRQ pin is pulled low. See Section 9. External Interrupt (IRQ). 1.5.5 Analog Power Supply/Reference Pins (VDDA, VREFH, VSSA and VREFL) VDDA and VSSA are the power supply pins for the analog-to-digital converter (ADC). Decoupling of these pins should be as per the digital supply. NOTE: VREFH is the high reference supply for the ADC. VDDA should be tied to the same potential as VDD via separate traces. Data Sheet General Description 23 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. General Description VREFL is the low reference supply for the ADC. VSSA should be tied to the same potential as VSS via separate traces. See Section 3. Analog-to-Digital Converter (ADC) Module. 1.5.6 Port A I/O Pins (PTA6/SS, PTA5/SPSCK, PTA4/KBD4-PTA0/KBD0) Port A input/output (I/O) pins (PTA6/SS, PTA5/SPSCK, PTA4/KBD4, PTA3/KBD3, PTA2/KBD2, PTA1/KBD1, and PTA0/KBD0) are special-function, bidirectional I/O port pins. PTA5 and PTA6 are shared with the serial peripheral interface (SPI). PTA4-PTA0 can be programmed to serve as keyboard interrupt pins. Freescale Semiconductor, Inc... See Section 12. Input/Output (I/O) Ports (PORTS) and Section 9. External Interrupt (IRQ). 1.5.7 Port B I/O Pins (PTB7/AD7/TBCH1, PTB6/AD6/TBCH0, PTB5/AD5-PTB0/AD0) PTB7/AD7/TBCH1, PTB6/AD6/TBCH0, and PTB5/AD5-PTB0/AD0 are special-function, bidirectional I/O port pins that can also be used for ADC inputs. PTB7/AD7/TBCH1 and PTB6/AD6/TBCH0 are special function bidirectional I/O port pins that can also be used for timer interface pins. See and Section 3. Analog-to-Digital Converter (ADC) Module and Section 17. Timer Interface A (TIMA) Module. 1.5.8 Port C I/O Pins (PTC4/OSC1, PTC3/OSC2, PTC2/MCLK, PTC1/MOSI, PTC0/MISO) PTC4/OSC1-PTC0/MISO are special-function, bidirectional I/O port pins. See Section 12. Input/Output (I/O) Ports (PORTS). PTC3/OSC2 and PTC4/OSC1 are shared with the on-chip oscillator circuit through configuration options. See Section 8. Internal Clock Generator (ICG) Module. When applications require: * * PTC3/OSC2 can be programmed to be OSC2 PTC4/OSC1 can be programmed to be OSC1 PTC2/MCLK is software selectable to be MCLK, or bus clock out. PTC1/MOSI can be programmed to be the MOSI signal for the SPI. PTC0/MISO can be programmed to be the MISO signal for the SPI. 1.5.9 Port D I/O Pins (PTD1/TACH1-PTD0/TACH0) PTD1/TACH1-PTD0/TACH0 are special-function, bidirectional I/O port pins that can also be programmed to be timer pins. See Section 17. Timer Interface A (TIMA) Module and Section 12. Input/Output (I/O) Ports (PORTS). Data Sheet 24 General Description MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. General Description Pin Functions 1.5.10 Port E I/O Pins (PTE1/RxD-PTE0/TxD) PTE1/RxD-PTE0/TxD are special-function, bidirectional I/O port pins that can also be programmed to be enhanced serial communication interface (ESCI) pins. See Section 13. Enhanced Serial Communications Interface (ESCI) Module and Section 12. Input/Output (I/O) Ports (PORTS). NOTE: Any unused inputs and I/O ports should be tied to an appropriate logic level (either VDD or VSS). Although the I/O ports of the MC68HC908EY16 do not require termination, termination is recommended to reduce the possibility of electro-static discharge damage. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA General Description Data Sheet 25 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. General Description Freescale Semiconductor, Inc... Data Sheet 26 General Description MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 2. Memory 2.1 Introduction The M68HC08 central processor unit (CPU08) can address 64 Kbytes of memory space. The memory map, shown in Figure 2-1, includes: * 16 Kbytes of FLASH memory, 15, 872 bytes of user space * 512 bytes of random-access memory (RAM) * 36 bytes of user-defined vectors * 310 bytes of monitor routines in read-only memory (ROM) * 1024 bytes of integrated FLASH burn-in routines in ROM Freescale Semiconductor, Inc... 2.2 Unimplemented Memory Locations Accessing an unimplemented location can cause an illegal address reset. In the memory map (Figure 2-1) and in register figures in this document, unimplemented locations are shaded. 2.3 Reserved Memory Locations Accessing a reserved location can have unpredictable effects on microcontroller unit (MCU) operation. In the Figure 2-1 and in register figures in this document, reserved locations are marked with the word reserved or with the letter R. 2.4 Input/Output (I/O) Section Most of the control, status, and data registers are in the zero page area of $0000-$003F. Additional I/O registers have these addresses: * $FE00; SIM break status register, SBSR * $FE01; SIM reset status register, SRSR * $FE03; SIM break flag control register, SBFCR * $FE08; FLASH control register, FLCR * $FE09; break address register high, BRKH * $FE0A; break address register low, BRKL * $FE0B; break status and control register, BRKSCR * $FE0C; LVI status register, LVISR * $FF7E; FLASH block protect register, FLBPR Data registers are shown in Figure 2-2. and Table 2-1 is a list of vector locations. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Memory Data Sheet 27 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory $0000 $003F $0040 $023F $0240 $0FFF Unimplemented 3520 Bytes RAM 512 Bytes I/O Registers 64 Bytes $FE08 $FE09 $FE0A $FE0B $FE0C $FE0D $FE0F $FE10 Reserved for Integrated FLASH Burn-in Routines 1024 Bytes $FE1F $FE20 Unimplemented 44,032 Bytes FF55 FF56 FLASH Memory 15,872 Bytes SIM Break Status Register (SBSR) SIM Reset Status Register (SRSR) Reserved SIM Break Flag Control Register (SBFCR) RESERVED RESERVED RESERVED Reserved for FLASH Test Control Register (FLTCR) FF7D $FF7E $FF7F $FFDB $FFDC $FFFF FLASH Control Register (FLCR) Break Address Register High (BRKH) Break Address Register Low (BRKL) Break Status and Control Register (BRKSCR) LVI Status Register (LVISR) Reserved 3 Bytes Reserved 16 Bytes Reserved for Compatibility with Monitor Code for A-Family Parts Freescale Semiconductor, Inc... $1000 $13FF $1400 $BFFF $C000 $FDFF $FE00 $FE01 $FE02 $FE03 $FE04 $FE05 $FE06 $FE07 Monitor ROM 310 Bytes Unimplemented 40 Bytes FLASH Block Protect Register (FLBPR) Unimplemented 93 Bytes FLASH Vectors 36 Bytes Note: Locations $FFF6-$FFFD are reserved for eight security bytes. Figure 2-1. Memory Map Data Sheet 28 Memory MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory Input/Output (I/O) Section Addr. Register Name Read: Port A Data Register (PTA) Write: See page 138. Reset: Read: Port B Data Register (PTB) Write: See page 140. Reset: Read: Port C Data Register (PTC) Write: See page 143. Reset: Port D Data Register Read: (PTD) Write: See page 145. Reset: Read: Data Direction Register A (DDRA) Write: See page 139. Reset: Read: Data Direction Register B (DDRB) Write: See page 141. Reset: Bit 7 0 6 PTA6 5 PTA5 4 PTA4 3 PTA3 2 PTA2 1 PTA1 Bit 0 PTA0 $0000 Unaffected by reset PTB7 PTB6 PTB5 PTB4 PTB3 PTB2 PTB1 PTB0 $0001 Unaffected by reset 0 0 0 PTC4 PTC3 PTC2 PTC1 PTC0 $0002 Freescale Semiconductor, Inc... Unaffected by reset 0 0 0 0 0 0 PTD1 PTD0 $0003 Unaffected by reset 0 DDRA6 0 DDRB6 0 0 DDRA5 0 DDRB5 0 0 DDRA4 0 DDRB4 0 DDRC4 0 0 DDRA3 0 DDRB3 0 DDRC3 0 0 DDRA2 0 DDRB2 0 DDRC2 0 0 DDRA1 0 DDRB1 0 DDRC1 0 DDRD1 0 PTE1 DDRA0 0 DDRB0 0 DDRC0 0 DDRD0 0 PTE0 $0004 0 DDRB7 0 $0005 $0006 Read: Data Direction MCLKEN Register C (DDRC) Write: See page 143. Reset: 0 Data Direction Read: Register D (DDRD) Write: See page 145. Reset: Read: Port E Data Register (PTE) Write: See page 147. Reset: Reserved 0 0 0 0 0 $0007 0 0 0 0 0 0 0 0 0 0 0 0 $0008 Unaffected by reset R R R R R R R R $0009 $000A Read: Data Direction Register E (DDRE) Write: See page 147. Reset: 0 0 0 0 0 0 DDRE1 0 DDRE0 0 0 0 = Unimplemented 0 0 R = Reserved 0 0 U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 1 of 7) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Memory Data Sheet 29 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory Addr. Register Name Read: BEMF Register (BEMF) Write: See page 61. Reset: Reserved Bit 7 BEMF7 6 BEMF6 5 BEMF5 4 BEMF4 3 BEMF3 2 BEMF2 1 BEMF1 Bit 0 BEMF0 $000B 0 R 0 R 0 R 0 R 0 R 0 R 0 R 0 R $000C $000D Read: SPI Control Register (SPCR) Write: See page 219. Reset: Read: SPI Status and Control Register (SPSCR) Write: See page 221. Reset: Read: SPI Data Register (SPDR) Write: See page 224. Reset: Read: ESCI Control Register 1 (SCC1) Write: See page 166. Reset: Read: ESCI Control Register 2 (SCC2) Write: See page 168. Reset: Read: ESCI Control Register 3 (SCC3) Write: See page 170. Reset: Read: ESCI Status Register 1 (SCS1) Write: See page 171. Reset: Read: ESCI Status Register 2 (SCS2) Write: See page 174. Reset: Read: ESCI Data Register (SCDR) Write: See page 175. Reset: SPRIE 0 SPRF R 0 ERRIE 0 R6 T6 SPMSTR 1 OVRF CPOL 0 MODF CPHA 1 SPTE SPWOM 0 MODFEN 0 R2 T2 SPE 0 SPR1 0 R1 T1 SPTIE 0 SPR0 0 R0 T0 Freescale Semiconductor, Inc... $000E 0 R7 T7 0 R5 T5 0 R4 T4 1 R3 T3 $000F Indeterminate after reset LOOPS 0 SCTIE 0 R8 ENSCI 0 TCIE 0 T8 0 TC TXINV 0 SCRIE 0 R 0 SCRF M 0 ILIE 0 R 0 IDLE WAKE 0 TE 0 ORIE 0 OR ILTY 0 RE 0 NEIE 0 NF PEN 0 RWU 0 FEIE 0 FE PTY 0 SBK 0 PEIE 0 PE $0010 $0011 $0012 U SCTE $0013 1 0 1 0 0 0 0 0 0 0 0 0 0 BKF 0 RPF $0014 0 R7 T7 0 R6 T6 0 R5 T5 0 R4 T4 0 R3 T3 0 R2 T2 0 R1 T1 0 R0 T0 $0015 Unaffected by reset = Unimplemented R = Reserved U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 2 of 7) Data Sheet 30 Memory MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory Input/Output (I/O) Section Addr. Register Name Read: ESCI Baud Rate Register (SCBR) Write: See page 175. Reset: Read: ESCI Prescale Register (SCPSC) Write: See page 177. Reset: ESCII Arbiter Control Read: Register Write: (SCIACTL) See page 180. Reset: Read: ESCI Arbiter Data Register (SCIACTL) Write: See page 181. Reset: Keyboard Status Read: and Control Register Write: (INTKBSCR) See page 130. Reset: Read: Keyboard Interrupt Enable Register (INTKBIER) Write: See page 131. Reset: Bit 7 R 0 PDS2 0 AM1 0 ARD7 6 LINR 0 PDS1 0 ALOST 5 SCP1 0 PDS0 0 AM0 0 ARD5 4 SCP0 0 PSSB4 0 ACLK 0 ARD4 3 R 0 PSSB3 0 AFIN 2 SCR2 0 PSSB2 0 ARUN 1 SCR1 0 PSSB1 0 AROVFL Bit 0 SCR0 0 PSSB0 0 ARD8 $0016 $0017 $0018 Freescale Semiconductor, Inc... 0 ARD6 0 ARD3 0 ARD2 0 ARD1 0 ARD0 $0019 0 0 0 0 0 0 0 0 0 KEYF 0 0 ACKK 0 IMASKK 0 KBIE1 0 TBON 0 IMASK 0 OSCENINSTOP 0 STOP 0 0 MODEK 0 KBIE0 0 R 0 MODE 0 SSBPUENB 1 COPD 0 $001A 0 0 0 0 0 0 0 KBIE4 0 TBR0 0 0 0 KBIE3 0 0 TACK 0 IRQF 0 KBIE2 0 TBIE 0 0 ACK $001B 0 TBIF 0 TBR2 0 0 0 TBR1 0 0 Read: Timebase Control Register Write: $001C (TBCR) See page 228. Reset: Read: IRQ Status and Control Register (INTSCR) Write: See page 123. Reset: Read: Configuration Register 2 Write: (CONFIG2) See page 66. Reset: Read: Configuration Register 1 (CONFIG1) Write: See page 66. Reset: 0 0 $001D 0 R 0 COPRS 0 0 ESCI BDSRC 0 LVISTOP 0 0 EXTXTALEN 0 LVIRSTD 0 0 EXTSLOW 0 LVIPWRD 0 0 EXTCLKEN 0 LVI5OR3(1) 0 0 TMBCLKSEL 0 SSREC 0 $001E $001F 1. The LVI5OR3 bit is cleared only by a power-on reset (POR). Read: Timer A Status and Control $0020 Register (TASC) Write: See page 239. Reset: TOF 0 0 TOIE 0 = Unimplemented TSTOP 1 0 TRST 0 R = Reserved R 0 PS2 0 PS1 0 PS0 0 U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 3 of 7) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Memory Data Sheet 31 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory Addr. Register Name Read: Timer A Counter Register High (TACNTH) Write: See page 241. Reset: Read: Timer A Counter Register Low (TACNTL) Write: See page 241. Reset: Read: Timer A Counter Modulo Register High (TAMODH) Write: See page 242. Reset: Read: Timer A Counter Modulo Register Low (TAMODL) Write: See page 242. Reset: Timer A Channel 0 Status Read: and Control Register Write: (TASC0) See page 243. Reset: Read: Timer A Channel 0 Register High (TACH0H) Write: See page 246. Reset: Read: Timer A Channel 0 Register Low (TACH0L) Write: See page 246. Reset: Timer A Channel 1 Status Read: and Control Register Write: (TASC1) See page 246. Reset: Read: Timer A Channel 1 Register High (TACH1H) Write: See page 246. Reset: Read: Timer A Channel 1 Register Low (TACH1L) Write: See page 246. Reset: Bit 7 BIT 15 6 BIT 14 5 BIT 13 4 BIT 12 3 BIT 11 2 BIT 10 1 BIT 9 Bit 0 BIT 8 $0021 0 BIT 7 0 BIT 6 0 BIT 5 0 BIT 4 0 BIT 3 0 BIT 2 0 BIT 1 0 BIT 0 $0022 0 BIT 15 1 BIT 7 1 CH0F 0 0 BIT 15 0 BIT 14 1 BIT 6 1 CH0IE 0 BIT 14 0 BIT 13 1 BIT 5 1 MS0B 0 BIT 13 0 BIT 12 1 BIT 4 1 MS0A 0 BIT 12 0 BIT 11 1 BIT 3 1 ELS0B 0 BIT 11 0 BIT 10 1 BIT 2 1 ELS0A 0 BIT 10 0 BIT 9 1 BIT 1 1 TOV0 0 BIT 9 0 BIT 8 1 BIT 0 1 CH0MAX 0 BIT 8 $0023 Freescale Semiconductor, Inc... $0024 $0025 $0026 Indeterminate after reset BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 $0027 Indeterminate after reset CH1F 0 0 BIT 15 CH1IE 0 BIT 14 0 R 0 BIT 13 MS1A 0 BIT 12 ELS1B 0 BIT 11 ELS1A 0 BIT 10 TOV1 0 BIT 9 CH1MAX 0 BIT 8 $0028 $0029 Indeterminate after reset BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 $002A Indeterminate after reset TOF 0 0 TOIE 0 = Unimplemented TSTOP 1 0 TRST 0 R = Reserved R 0 PS2 0 PS1 0 PS0 0 Read: Timer B Status and Control $002B Register (TBSC) Write: See page 257. Reset: U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 4 of 7) Data Sheet 32 Memory MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory Input/Output (I/O) Section Addr. Register Name Read: Timer B Counter Register High (TBCNTH) Write: See page 259. Reset: Read: Timer B Counter Register Low (TBCNTL) Write: See page 259. Reset: Read: Timer B Counter Modulo Register High (TBMODH) Write: See page 260. Reset: Read: Timer B Counter Modulo Register Low (TBMODL) Write: See page 260. Reset: Timer B Channel 0 Status Read: and Control Register Write: (TBSC0) See page 261. Reset: Read: Timer B Channel 0 Register High (TBCH0H) Write: See page 264. Reset: Read: Timer B Channel 0 Register Low (TBCH0L) Write: See page 264. Reset: Timer B Channel 1 Status Read: and Control Register Write: (TBSC1) See page 261. Reset: Read: Timer B Channel 1 Register High (TBCH1H) Write: See page 264. Reset: Read: Timer B Channel 1 Register Low (TBCH1L) Write: See page 264. Reset: Read: ICG Control Register (ICGCR) Write: See page 114. Reset: Bit 7 BIT 15 6 BIT 14 5 BIT 13 4 BIT 12 3 BIT 11 2 BIT 10 1 BIT 9 Bit 0 BIT 8 $002C 0 BIT 7 0 BIT 6 0 BIT 5 0 BIT 4 0 BIT 3 0 BIT 2 0 BIT 1 0 BIT 0 $002D 0 BIT 15 1 BIT 7 1 CH0F 0 0 BIT 15 0 BIT 14 1 BIT 6 1 CH0IE 0 BIT 14 0 BIT 13 1 BIT 5 1 MS0B 0 BIT 13 0 BIT 12 1 BIT 4 1 MS0A 0 BIT 12 0 BIT 11 1 BIT 3 1 ELS0B 0 BIT 11 0 BIT 10 1 BIT 2 1 ELS0A 0 BIT 10 0 BIT 9 1 BIT 1 1 TOV0 0 BIT 9 0 BIT 8 1 BIT 0 1 CH0MAX 0 BIT 8 $002E Freescale Semiconductor, Inc... $002F $0030 $0031 Indeterminate after reset BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 $0032 Indeterminate after reset CH1F 0 0 BIT 15 CH1IE 0 BIT 14 0 R 0 BIT 13 MS1A 0 BIT 12 ELS1B 0 BIT 11 ELS1A 0 BIT 10 TOV1 0 BIT 9 CH1MAX 0 BIT 8 $0033 $0034 Indeterminate after reset BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 $0035 Indeterminate after reset CMIE 0 CMF 0 0 = Unimplemented CMON 0 CS 0 R = Reserved ICGON 1 ICGS ECGON 0 ECGS $0036 0 0 U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 5 of 7) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Memory Data Sheet 33 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory Addr. Register Name Read: ICG Multiplier Register (ICGMR) Write: See page 116. Reset: Bit 7 6 N6 5 N5 0 TRIM5 0 4 N4 1 TRIM4 0 3 N3 0 TRIM3 0 DDIV3 2 N2 1 TRIM2 0 DDIV2 1 N1 0 TRIM1 0 DDIV1 Bit 0 N0 1 TRIM0 0 DDIV0 $0037 0 TRIM7 1 0 TRIM6 0 Read: ICG Trim Register (ICGTR) $0038 Write: See page 116. Reset: Read: ICG Divider Control Register (ICGDVR) Write: See page 117. Reset: Read: ICG DCO Stage Control Register (ICGDSR) Write: See page 117. Reset: Reserved $0039 Freescale Semiconductor, Inc... 0 DSTG7 R U R 0 DSTG6 R U R 0 DSTG5 R U R 0 DSTG4 R U R U DDSTG3 R U R U DSTG2 R U R U DSTG1 R U R U DSTG0 R U R $003A $003B $003C Analog-to-Digital Status Read: and Control Register Write: (ADSCR) See page 54. Reset: Read: Analog-to-Digital Data Register High (ADRH) Write: See page 56. Reset: Read: Analog-to-Digital Data Register Low (ADRL) Write: See page 58. Reset: Read: Analog-to-Digital Clock Register (ADCLK) Write: See page 58. Reset: COCO 0 0 AIEN 0 0 ADCO 0 0 ADCH4 1 0 ADCH3 1 0 ADCH2 1 0 ADCH1 1 ADCH9 ADCH0 1 ADCH8 $003D Unaffected by reset AD7 AD6 AD5 AD4 AD3 AD2 AD1 AD0 $003E Unaffected by reset ADIV2 0 R 0 ADIV1 0 R 0 ADIV0 0 R 0 ADICLK 0 R 0 MODE1 0 R 0 MODE0 1 R 0 R 0 SBSW NOTE 0 0 $003F 0 R 0 Read: SIM Break Status Register $FE00 (SBSR) Write: See page 198. Reset: Note: Writing a 0 clears SBSW. Read: SIM Reset Status Register $FE01 (SRSR) Write: See page 199. POR: POR PIN COP ILOP ILAD MENRST LVI 0 1 0 = Unimplemented 0 0 R = Reserved 0 0 0 0 U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 6 of 7) Data Sheet 34 Memory MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory Input/Output (I/O) Section Addr. $FE02 Register Name Reserved Bit 7 6 5 4 3 2 1 Bit 0 $FE03 $FE04 $FE07 SIM Break Flag Control Register (SBFCR) Reserved BCFE R R R R R R R Reserved Freescale Semiconductor, Inc... $FE08 Read: FLASH Control Register (FLCR) Write: See page 38. Reset: Read: Break Address Register High (BRKH) Write: See page 270. Reset: Read: Break Address Register Low (BRKL) Write: See page 270. Reset: Read: Break Status and Control Register (BSCR) Write: See page 269. Reset: Read: LVI Status Register (LVISR) Write: See page 135. Reset: Read: FLASH Block Protect (1) Write: Register (FLBPR) See page 43. Reset: 0 0 0 0 HVEN 0 BIT 11 0 BIT 3 0 0 MASS 0 BIT 10 0 BIT 2 0 0 ERASE 0 BIT 9 0 BIT 1 0 0 PGM 0 BIT 8 0 BIT 0 0 0 0 BIT 15 0 BIT 7 0 BRKE 0 LVIOUT 0 BIT 14 0 BIT 6 0 BRKA 0 0 0 BIT 13 0 BIT 5 0 0 0 BIT 12 0 BIT 4 0 0 $FE09 $FE0A $FE0B 0 0 0 0 0 0 0 0 0 0 0 0 $FE0C 0 BPR7 0 BPR6 0 BPR5 0 BPR4 0 BPR3 0 BPR2 0 BPR1 0 BPR0 $FF7E Unaffected by reset 1. Non-volatile FLASH register $FFFF Read: COP Control Register (COPCTL) Write: See page 73. Reset: = Unimplemented Low byte of reset vector Writing clears COP counter (any value) Unaffected by reset R = Reserved U = Unaffected Figure 2-2. Control, Status, and Data Registers (Sheet 7 of 7) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Memory Data Sheet 35 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory Table 2-1. Vector Addresses Vector Priority Lowest Vector IF15 IF15 IF14 IF13 Address $FFDC $FFDD $FFDE $FFDF $FFE0 $FFE1 $FFE2 $FFE3 $FFE4 $FFE5 $FFE6 $FFE7 $FFE8 $FFE9 $FFEA $FFEB $FFEC $FFED $FFEE $FFEF $FFF0 $FFF1 $FFF2 $FFF3 $FFF4 $FFF5 $FFF6 $FFF7 $FFF8 $FFF9 $FFFA $FFFB $FFFC $FFFD $FFFE $FFFF Vector Timebase interrupt vector (high) Timebase interrupt vector (low) SPI transmit vector (high) SPI transmit vector (low) SPI receive vector (high) SPI receive vector (low) ADC conversion complete vector (high) ADC conversion complete vector (low) Keyboard vector (high) Keyboard vector (low) ESCI transmit vector (high) ESCI transmit vector (low) ESCI receive vector (high) ESCI receive vector (low) ESCI error vector (high) ESCI error vector (low) TIMB overflow vector (high) TIMB overflow vector (low) TIMB channel 1 vector (high) TIMB channel 1 vector (low) TIMB channel 0 vector (high) TIMB channel 0 vector (low) TIMA overflow vector (high) TIMA overflow vector (low) TIMA channel 1 vector (high) TIMA channel 1 vector (low) TIMA channel 0 vector (high) TIMA channel 0 vector (low) CMIREQ (high) CMIREQ (low) IRQ vector (high) IRQ vector (low) SWI vector (high) SWI vector (low) Reset vector (high) Reset vector (low) Freescale Semiconductor, Inc... IF12 IF11 IF10 IF9 IF8 IF7 IF6 IF5 IF4 IF3 IF2 IF1 -- -- Highest Data Sheet 36 Memory MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory Random Access Memory (RAM) 2.5 Random Access Memory (RAM) Addresses $0040-$00FF and $0100-$023F are RAM locations. The location of the stack RAM is programmable with the reset stack pointer instruction (RSP). The 16-bit stack pointer allows the stack RAM to be anywhere in the 64K-byte memory space. NOTE: For correct operation, the stack pointer must point only to RAM locations. Within page zero are 192 bytes of RAM. Because the location of the stack RAM is programmable, all page zero RAM locations can be used for input/output (I/O) control and user data or code. When the stack pointer is moved from its reset location at $00FF, direct addressing mode instructions can access all page zero RAM locations efficiently. Page zero RAM, therefore, provides ideal locations for frequently accessed global variables. Before processing an interrupt, the CPU uses five bytes of the stack to save the contents of the central processor unit (CPU) registers. NOTE: For M6805, M146805, and M68HC05 compatibility, the H register is not stacked. During a subroutine call, the CPU uses two bytes of the stack to store the return address. The stack pointer decrements during pushes and increments during pulls. NOTE: Be careful when using nested subroutines. The CPU could overwrite data in the RAM during a subroutine or during the interrupt stacking operation. Freescale Semiconductor, Inc... 2.6 FLASH Memory (FLASH) The FLASH memory is an array of 15,872 bytes with an additional 36 bytes of user vectors and one byte used for block protection. NOTE: An erased bit reads as 1 and a programmed bit reads as 0. The program and erase operations are facilitated through control bits in the FLASH control register (FLCR). See 2.6.1 FLASH Control Register. The FLASH is organized internally as an 16,384-word by 8-bit complementary metal-oxide semiconductor (CMOS) page erase, byte (8-bit) program embedded FLASH memory. Each page consists of 64 bytes. The page erase operation erases all words within a page. A page is composed of two adjacent rows. A security feature prevents viewing of the FLASH contents.(1) In the 125C to 135C temperature range, the FLASH is guaranteed as read only. 1. No security feature is absolutely secure. However, Motorola's strategy is to make reading or copying the FLASH difficult for unauthorized users. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Memory Data Sheet 37 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory 2.6.1 FLASH Control Register The FLASH control register (FLCR) controls FLASH program and erase operations. Address: Read: Write: Reset: 0 0 = Unimplemented 0 0 $FE08 Bit 7 0 6 0 5 0 4 0 3 HVEN 0 2 MASS 0 1 ERASE 0 Bit 0 PGM 0 Freescale Semiconductor, Inc... Figure 2-3. FLASH Control Register (FLCR) HVEN -- High-Voltage Enable Bit This read/write bit enables the charge pump to drive high voltages for program and erase operations in the array. HVEN can be set only if either PGM = 1 or ERASE = 1 and the proper sequence for program or erase is followed. 1 = High voltage enabled to array and charge pump on 0 = High voltage disabled to array and charge pump off MASS -- Mass Erase Control Bit Setting this read/write bit configures the 16-Kbyte FLASH array for mass or page erase operation. 1 = Mass erase operation selected 0 = Page erase operation selected ERASE -- Erase Control Bit This read/write bit configures the memory for erase operation. ERASE is interlocked with the PGM bit such that both bits cannot be equal to 1 or set to 1 at the same time. 1 = Erase operation selected 0 = Erase operation unselected PGM -- Program Control Bit This read/write bit configures the memory for program operation. PGM is interlocked with the ERASE bit such that both bits cannot be equal to 1 or set to 1 at the same time. 1 = Program operation selected 0 = Program operation unselected Data Sheet 38 Memory MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory FLASH Memory (FLASH) 2.6.2 FLASH Page Erase Operation Use this step-by-step procedure to erase a page (64 bytes) of FLASH memory to read as logic 1: 1. Set the ERASE bit and clear the MASS bit in the FLASH control register. 2. Read the FLASH block protect register. 3. Write any data to any FLASH location within the address range of the block to be erased. 4. Wait for a time, tNVS (minimum 10 s). 5. Set the HVEN bit. 6. Wait for a time, tErase (minimum 1 ms or 4 ms). 7. Clear the ERASE bit. 8. Wait for a time, tNVH (minimum 5 s). 9. Clear the HVEN bit. 10. After time, tRCV (typical 1 s), the memory can be accessed in read mode again. NOTE: NOTE: While these operations must be performed in the order shown, other unrelated operations may occur between the steps. Due to the security feature (see 19.3 Monitor Module (MON)) the last page of the FLASH (0xFFDC-0xFFFF), which contains the security bytes, cannot be erased by Page Erase Operation. It can only be erased with the Mass Erase Operation. In applications that require more than 1000 program/erase cycles, use the 4 ms page erase specification to get improved long-term reliability. Any application can use this 4 ms page erase specification. However, in applications where a FLASH location will be erased and reprogrammed less than 1000 times, and speed is important, use the 1 ms page erase specification to get a shorter cycle time. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Memory Data Sheet 39 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory 2.6.3 FLASH Mass Erase Operation Use this step-by-step procedure to erase entire FLASH memory to read as logic 1: 1. Set both the ERASE bit and the MASS bit in the FLASH control register. 2. Read the FLASH block protect register. 3. Write any data to any FLASH address(1) within the FLASH memory address range. 4. Wait for a time, tNVS (minimum 10 s). 5. Set the HVEN bit. 6. Wait for a time, tMErase (minimum 4 ms). 7. Clear the ERASE and MASS bits. NOTE: Mass erase is disabled whenever any block is protected (FLBPR does not equal $FF). 8. Wait for a time, tNVHL (minimum 100 s). 9. Clear the HVEN bit. 10. After time, tRCV (typical 1 s), the memory can be accessed in read mode again. NOTE: Programming and erasing of FLASH locations cannot be performed by code being executed from the FLASH memory. While these operations must be performed in the order as shown, but other unrelated operations may occur between the steps. Freescale Semiconductor, Inc... 1. When in monitor mode, with security sequence failed (see 19.3.2 Security), write to the FLASH block protect register instead of any FLASH address. Data Sheet 40 Memory MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory FLASH Memory (FLASH) 2.6.4 FLASH Program/Read Operation Programming of the FLASH memory is done on a row basis. A row consists of 32 consecutive bytes starting from addresses $XX00, $XX20, $XX40, $XX60, $XX80, $XXA0, $XXC0, and $XXE0. Use this step-by-step procedure to program a row of FLASH memory (Figure 2-4 is a flowchart representation). NOTE: To avoid program disturbs, the row must be erased before any byte on that row is programmed. 1. Set the PGM bit. This configures the memory for program operation and enables the latching of address and data for programming. 2. Read from the FLASH block protect register. 3. Write any data to any FLASH address within the row address range desired. 4. Wait for a time, tNVS (minimum of 10 s). 5. Set the HVEN bit. 6. Wait for a time, tPGS (minimum of 5 s). 7. Write data to the FLASH address(1) to be programmed. 8. Wait for a time, tPROG (minimum of 30 s). 9. Repeat steps 7 and 8 until all the bytes within the row are programmed. 10. Clear the PGM bit.(1) 11. Wait for a time, tNVH (minimum of 5 s). 12. Clear the HVEN bit. 13. After a time, tRCV (minimum of 1 s), the memory can be accessed in read mode again. This program sequence is repeated throughout the memory until all data is programmed. NOTE: Programming and erasing of FLASH locations cannot be performed by code being executed from the FLASH memory. While these operations must be performed in the order shown, other unrelated operations may occur between the steps. Do not exceed tPROG maximum. Freescale Semiconductor, Inc... 1. The time between each FLASH address change, or the time between the last FLASH address programmed to clearing the PGM bit, must not exceed the maximum programming time, tPROG maximum. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Memory Data Sheet 41 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory Algorithm for Programming a Row (32 bytes) of FLASH Memory 1 SET PGM BIT 2 READ THE FLASH BLOCK PROTECT REGISTER 3 WRITE ANY DATA TO ANY FLASH ADDRESS WITHIN THE ROW ADDRESS RANGE DESIRED 4 WAIT FOR A TIME, tNVS Freescale Semiconductor, Inc... 5 SET HVEN BIT 6 WAIT FOR A TIME, tPGS 7 WRITE DATA TO THE FLASH ADDRESS TO BE PROGRAMMED 8 WAIT FOR A TIME, tPROG COMPLETED PROGRAMMING THIS ROW? YES NO 10 CLEAR PGM BIT 11 WAIT FOR A TIME, tNVH Notes: The time between each FLASH address change (step 7 to step 7), or the time between the last FLASH address programmed to clearing PGM bit (step 7 to step 10) must not exceed the maximum programming time, tPROG maximum. This row program algorithm assumes the row/s to be programmed are initially erased. 12 CLEAR HVEN BIT 13 WAIT FOR A TIME, tRCV END OF PROGRAMMING Figure 2-4. FLASH Programming Flowchart Data Sheet 42 Memory MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory FLASH Memory (FLASH) 2.6.5 FLASH Block Protection Due to the ability of the on-board charge pump to erase and program the FLASH memory in the target application, provision is made for protecting a block of memory from unintentional erase or program operations due to system malfunction. This protection is done by using the FLASH block protect register (FLBPR). The FLBPR determines the range of the FLASH memory which is to be protected. The range of the protected area starts from a location defined by FLBPR and ends at the bottom of the FLASH memory ($FFFF). When the memory is protected, the HVEN bit cannot be set in either erase or program operations. NOTE: In performing a program or erase operation, FLBPR must be read after setting the PGM or ERASE bit and before asserting the HVEN bit. When FLBPR is programmed with all 0s, the entire memory is protected from being programmed and erased. When all the bits are erased (all 1s), the entire memory is accessible for program and erase. When bits within the FLBPR are programmed, they lock a block of memory address ranges as shown in 2.6.6 FLASH Block Protect Register. Once the FLBPR is programmed with a value other than $FF or $FE, any erase or program of the FLBPR or the protected block of FLASH memory is prohibited. Mass erase is disabled whenever any block is protected (FLBPR does not equal $FF). The presence of a VTST on the IRQ pin will bypass the block protection so that all of the memory included in the block protect register is open for program and erase operations. 2.6.6 FLASH Block Protect Register The FLASH block protect register (FLBPR) is implemented as a byte within the FLASH memory, and therefore can be written only during a programming sequence of the FLASH memory. The value in this register determines the starting location of the protected range within the FLASH memory. Address: Read: Write: Reset: $FF7E Bit 7 BPR7 6 BPR6 5 BPR5 4 BPR4 3 BPR3 2 BPR2 1 BPR1 Bit 0 BPR0 Freescale Semiconductor, Inc... Unaffected by reset. Initial value from factory is $FF. Write to this register is by a programming sequence to the FLASH memory. Figure 2-5. FLASH Block Protect Register (FLBPR) BPR7-BPR0 -- FLASH Block Protect Bits These eight bits represent bits [13:6] of a 16-bit memory address. Bit 15 and Bit 14 are 1s and bits [5:0] are 0s. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Memory Data Sheet 43 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory The resultant 16-bit address is used for specifying the start address of the FLASH memory for block protection. The FLASH is protected from this start address to the end of FLASH memory, at $FFFF. With this mechanism, the protect start address can be $XX00, $XX40, $XX80, and $XXC0 (64 bytes page boundaries) within the FLASH memory. 16-BIT MEMORY ADDRESS START ADDRESS OF FLASH 1 BLOCK PROTECT 1 FLBPR VALUE 0 0 0 0 0 0 Figure 2-6. FLASH Block Protect Start Address Freescale Semiconductor, Inc... Table 2-2. Examples of Protect Address Ranges BPR[7:0] $00 $01 (0000 0001) $02 (0000 0010) $03 (0000 0011) $04 (0000 0100) Addresses of Protect Range The entire FLASH memory is protected. $C040 (1100 0000 0100 0000) -- $FFFF $C080 (1100 0000 1000 0000) -- $FFFF $C0C0 (1100 0000 1100 0000) -- $FFFF $C100 (1100 0001 0000 0000) -- $FFFF and so on... $FC (1111 1100) $FD (1111 1101) $FE (1111 1110) $FF $FF00 (1111 1111 0000 0000) -- FFFF $FF40 (1111 1111 0100 0000) -- $FFFF FLBPR and vectors are protected $FF80 (1111 1111 1000 0000) -- FFFF Vectors are protected The entire FLASH memory is not protected. 2.6.7 Wait Mode Putting the microcontroller unit (MCU) into wait mode while the FLASH is in read mode does not affect the operation of the FLASH memory directly, but there will not be any memory activity since the CPU is inactive. The WAIT instruction should not be executed while performing a program or erase operation on the FLASH, or the operation will discontinue and the FLASH will be on standby mode. 2.6.8 Stop Mode Putting the MCU into stop mode while the FLASH is in read mode does not affect the operation of the FLASH memory directly, but there will not be any memory activity since the CPU is inactive. Data Sheet 44 Memory MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory FLASH Memory (FLASH) The STOP instruction should not be executed while performing a program or erase operation on the FLASH, or the operation will discontinue and the FLASH will be on standby mode NOTE: Standby mode is the power-saving mode of the FLASH module in which all internal control signals to the FLASH are inactive and the current consumption of the FLASH is at a minimum. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Memory Data Sheet 45 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Memory Freescale Semiconductor, Inc... Data Sheet 46 Memory MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 3. Analog-to-Digital Converter (ADC) Module 3.1 Introduction This section describes the 10-bit analog-to-digital converter (ADC). For further information regarding analog-to-digital converters on Motorola microcontrollers, please consult the HC08 ADC Reference Manual, ADCRM/AD. Freescale Semiconductor, Inc... 3.2 Features Features of the ADC module include: * * * * * * * * * 8 channels with multiplexed input Linear successive approximation 10-bit resolution, 8-bit accuracy Single or continuous conversion Conversion complete flag or conversion complete interrupt Selectable ADC clock Left or right justified result Left justified sign data mode High impedance buffered ADC input 3.3 Functional Description Eight ADC channels are available for sampling external sources at pins PTB7:PTB0. To achieve the best possible accuracy, these pins are implemented as input-only pins when the analog-to-digital (A/D) feature is enabled. An analog multiplexer allows the single ADC to select one of the 8 ADC channels as ADC voltage IN (ADCVIN). ADCVIN is converted by the successive approximation algorithm. When the conversion is completed, the ADC places the result in the ADC data register (ADRH and ADRL) and sets a flag or generates an interrupt. See Figure 3-2. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Analog-to-Digital Converter (ADC) Module Data Sheet 47 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module INTERNAL BUS M68HC08 CPU CPU REGISTERS ARITHMETIC/LOGIC UNIT (ALU) SINGLE BREAKPOINT BREAK MODULE PORT A DDRA 5-BIT KEYBOARD INTERRUPT MODULE PTA6/SS PTA5/SPSCK PTA4/KBD4 PTA3/KBD3 PTA2/KBD2 PTA1/KBD1 2-CHANNEL TIMER INTERFACE MODULE A PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PORT B DDRB PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK PTC1/MOSI PTC0/MISO PTD1/TACH1 PTD0/TACH0 PTE1/RxD PTE0/TxD PORT C PORT E PORT D CONTROL AND STATUS REGISTERS 64 BYTES USER FLASH 15,872 BYTES USER RAM 512 BYTES Freescale Semiconductor, Inc... MONITOR ROM 310 BYTES FLASH PROGRAMMING (BURN-IN) ROM 1024 BYTES USER FLASH VECTOR SPACE 36 BYTES 2-CHANNEL TIMER INTERFACE MODULE B ENHANCED SERIAL COMMUNICATION INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE OSC2 OSC1 INTERNAL CLOCK GENERATOR MODULE SERIAL PERIPHERAL INTERFACE MODULE RST 24 INTERNAL SYSTEM INTEGRATION MODULE SINGLE EXTERNAL IRQ MODULE CONFIGURATION REGISTER MODULE PERIODIC WAKEUP TIMEBASE MODULE ARBITER MODULE PRESCALER MODULE IRQ VREFH VDDA VREFL VSSA VDD VSS DDRE DDRD DDRC 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE SECURITY MODULE POWER BEMF MODULE Figure 3-1. Block Diagram Highlighting ADC Block and Pins Data Sheet 48 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Analog-to-Digital Converter (ADC) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module Functional Description INTERNAL DATA BUS PTB READ PTB ADC CHANNEL x DISABLE ADC DATA REGISTERS Freescale Semiconductor, Inc... INTERRUPT LOGIC AIEN CONVERSION COMPLETE ADC VOLTAGE IN ADVIN ADC CHANNEL SELECT ADCH[4:0] COCO/IDMAS ADC CLOCK PTx CGMXCLK BUS CLOCK CLOCK GENERATOR ADIV[2:0] ADICLK Figure 3-2. ADC Block Diagram 3.3.1 ADC Port I/O Pins PTB7:PTB0 are general-purpose I/O pins that are shared with the ADC channels. See Section 12. Input/Output (I/O) Ports (PORTS). The channel select bits define which ADC channel/port pin will be used as the input signal. The ADC overrides the port logic when that port is selected by the ADC multiplexer. The remaining ADC channels/port pins are controlled by the port logic and can be used as general-purpose input/output (I/O) pins. Writes to the port register or DDR will not have any effect on the port pin that is selected by the ADC. Read of a port pin which is in use by the ADC will return a logic 0. 3.3.2 Voltage Conversion When the input voltage to the ADC equals VREFH, the ADC converts the signal to $3FF (full scale). If the input voltage equals VREFL, the ADC converts it to $000. Input voltages between VREFH and VREFL are straight-line linear conversions. All other input voltages will result in $3FF if greater than VREFH and $000 if less than VREFL. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Analog-to-Digital Converter (ADC) Module Data Sheet 49 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module NOTE: Input voltage should not exceed the analog supply voltages. See 20.10 Analog-to-Digital Converter (ADC) Characteristics. 3.3.3 Conversion Time Conversion starts after a write to the ADSCR. A conversion is between 16 and 17 ADC clock cycles, therefore: Conversion time = 16 to17 ADC Cycles ADC Frequency Freescale Semiconductor, Inc... Number of Bus Cycles = Conversion Time x Bus Frequency The ADC conversion time is determined by the clock source chosen and the divide ratio selected. The clock source is either the bus clock or CGMXCLK and is selectable by ADICLK located in the ADC clock register. For example, if CGMXCLK is 4 MHz and is selected as the ADC input clock source, the ADC input clock divide-by-2 prescale is selected and the bus frequency is 8 MHz: Conversion Time = 16 to17 ADC Cycles = 8 to 8.5 s 4 MHz/2 Number of bus cycles = (8 to 8.5s) x 8 MHz = 64 to 68 cycles The ADC frequency must be between fADIC minimum and fADIC maximum to meet A/D specifications. See 20.10 Analog-to-Digital Converter (ADC) Characteristics. Since an ADC cycle may be comprised of several bus cycles (four in the previous example) and the start of a conversion is initiated by a bus cycle write to the ADSCR, from zero to four additional bus cycles may occur before the start of the initial ADC cycle. This results in a fractional ADC cycle and is represented as the 17th cycle. 3.3.4 Continuous Conversion In continuous conversion mode, the ADC data registers ADRH and ADRL will be filled with new data after each conversion. Data from the previous conversion will be overwritten whether that data has been read or not. Conversions will continue until the ADCO bit is cleared. The COCO bit is set after the first conversion and will stay set for the next several conversions until the next write of the ADC status and control register or the next read of the ADC data register. Data Sheet 50 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Analog-to-Digital Converter (ADC) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module Interrupts 3.3.5 Result Justification The conversion result may be formatted in four different ways: 1. Left justified 2. Right justified 3. Left Justified sign data mode 4. 8-bit truncation mode All four of these modes are controlled using MODE0 and MODE1 bits located in the ADC clock register (ADCLK). Freescale Semiconductor, Inc... Left justification will place the eight most significant bits (MSB) in the corresponding ADC data register high, ADRH. This may be useful if the result is to be treated as an 8-bit result where the two least significant bits (LSB), located in the ADC data register low, ADRL, can be ignored. However, ADRL must be read after ADRH or else the interlocking will prevent all new conversions from being stored. Right justification will place only the two MSBs in the corresponding ADC data register high, ADRH, and the eight LSBs in ADC data register low, ADRL. This mode of operation typically is used when a 10-bit unsigned result is desired. Left justified sign data mode is similar to left justified mode with one exception. The MSB of the 10-bit result, AD9 located in ADRH, is complemented. This mode of operation is useful when a result, represented as a signed magnitude from mid-scale, is needed. Finally, 8-bit truncation mode will place the eight MSBs in ADC data register low, ADRL. The two LSBs are dropped. This mode of operation is used when compatibility with 8-bit ADC designs are required. No interlocking between ADRH and ADRL is present. NOTE: Quantization error is affected when only the most significant eight bits are used as a result. See Figure 3-3. 3.3.6 Monotonicity The conversion process is monotonic and has no missing codes. 3.4 Interrupts When the AIEN bit is set, the ADC module is capable of generating a CPU interrupt after each ADC conversion. A CPU interrupt is generated if the COCO bit is at 0. The COCO bit is not used as a conversion complete flag when interrupts are enabled. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Analog-to-Digital Converter (ADC) Module Data Sheet 51 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module 8-BIT 10-BIT RESULT RESULT 003 00B 00A 009 002 008 007 006 IDEAL 8-BIT CHARACTERISTIC WITH QUANTIZATION = 1/2 10-BIT TRUNCATED TO 8-BIT RESULT IDEAL 10-BIT CHARACTERISTIC WITH QUANTIZATION = 1/2 Freescale Semiconductor, Inc... 005 001 004 003 002 001 000 000 1/2 1 1/2 1/2 2 1/2 3 1/2 4 1/2 5 1/2 1 1/2 6 1/2 7 1/2 8 1/2 9 1/2 2 1/2 INPUT VOLTAGE REPRESENTED AS 10-BIT INPUT VOLTAGE REPRESENTED AS 8-BIT WHEN TRUNCATION IS USED, ERROR FROM IDEAL 8-BIT = 3/8 LSB DUE TO NON-IDEAL QUANTIZATION. Figure 3-3. 8-Bit Truncation Mode Error 3.5 Wait Mode The WAIT instruction can put the MCU in low power-consumption standby mode. The ADC continues normal operation during wait mode. Any enabled CPU interrupt request from the ADC can bring the MCU out of wait mode. If the ADC is not required to bring the MCU out of wait mode, power down the ADC by setting ADCH[4:0] in the ADC status and control register before executing the WAIT instruction. 3.6 I/O Signals The ADC module has eight input signals. 3.6.1 ADC Analog Power Pin (VDDA) The ADC analog portion uses VDDA as its power pin. Connect the VDDA pin to the same voltage potential as VDD. External filtering may be necessary to ensure clean VDDA for good results. NOTE: Route VDDA carefully for maximum noise immunity and place bypass capacitors as close as possible to the package. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Analog-to-Digital Converter (ADC) Module MOTOROLA Data Sheet 52 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module I/O Signals 3.6.2 ADC Analog Ground Pin (VSSA) The ADC analog portion uses VSSA as its ground pin. Connect the VSSA pin to the same voltage potential as VSS. 3.6.3 ADC Voltage Reference Pin (VREFH) VREFH is the power supply for setting the reference voltage VREFH. Connect the VREFH pin to the same voltage potential as VDDA. There will be a finite current associated with VREFH. See Section 20. Electrical Specifications. NOTE: Route VREFH carefully for maximum noise immunity and place bypass capacitors as close as possible to the package. Freescale Semiconductor, Inc... 3.6.4 ADC Voltage Reference Low Pin (VREFL) VREFL is the lower reference supply for the ADC. Connect the VREFL pin to the same voltage potential as VSSA. A finite current will be associated with VREFL. See Section 20. Electrical Specifications. 3.6.5 ADC Voltage In (ADVIN) ADVIN is the input voltage signal from one of the 8 ADC channels to the ADC module. 3.6.6 ADC External Connections This section describes the ADC external connections: VREFH and VREFL, ANx, and grounding. 3.6.6.1 VREFH and VREFL Both ac and dc current are drawn through the VREFH and VREFL loop. The AC current is in the form of current spikes required to supply charge to the capacitor array at each successive approximation step. The current flows through the internal resistor string. The best external component to meet both these current demands is a capacitor in the 0.01 F to 1 F range with good high frequency characteristics. This capacitor is connected between VREFH and VREFL and must be placed as close as possible to the package pins. Resistance in the path is not recommended because the dc current will cause a voltage drop which could result in conversion errors. 3.6.6.2 ANx Empirical data shows that capacitors from the analog inputs to VREFL improve ADC performance. 0.01-F and 0.1-F capacitors with good high-frequency characteristics are sufficient. These capacitors must be placed as close as possible to the package pins. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Analog-to-Digital Converter (ADC) Module Data Sheet 53 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module 3.6.6.3 Grounding In cases where separate power supplies are used for analog and digital power, the ground connection between these supplies should be at the VSSA pin. This should be the only ground connection between these supplies if possible. The VSSA pin makes a good single point ground location. Connect the VREFL pin to the same potential as VSSA at the single point ground location. 3.7 I/O Registers These I/O registers control and monitor operation of the ADC: * * * ADC status and control register, ADSCR ADC data registers, ADRH and ARDL ADC clock register, ADCLK Freescale Semiconductor, Inc... 3.7.1 ADC Status and Control Register This section describes the function of the ADC status and control register (ADSCR). Writing ADSCR aborts the current conversion and initiates a new conversion. Address: Read: Write: Reset: $003C Bit 7 COCO 0 6 AIEN 0 5 ADCO 0 4 ADCH4 1 3 ADCH3 1 2 ADCH2 1 1 ADCH1 1 Bit 0 ADCH0 1 Figure 3-4. ADC Status and Control Register (ADSCR) COCO -- Conversions Complete Bit When AIEN bit is 0, the COCO is a read-only bit which is set each time a conversion is completed except in the continuous conversion mode where it is set after the first conversion. This bit is cleared whenever the ADC status and control register is written or whenever the ADC data register is read. If AIEN bit is 1, the COCO is a read/write bit. Reset clears this bit. 1 = Conversion completed (AIEN = 0) 0 = Conversion not completed (AIEN = 0)/CPU interrupt (AIEN = 1) AIEN -- ADC Interrupt Enable Bit When this bit is set, an interrupt is generated at the end of an ADC conversion. The interrupt signal is cleared when the data register is read or the status/control register is written. Reset clears the AIEN bit. 1 = ADC interrupt enabled 0 = ADC interrupt disabled Data Sheet 54 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Analog-to-Digital Converter (ADC) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module I/O Registers ADCO -- ADC Continuous Conversion Bit When set, the ADC will convert samples continuously and update the ADR register at the end of each conversion. Only one conversion is allowed when this bit is cleared. Reset clears the ADCO bit. 1 = Continuous ADC conversion 0 = One ADC conversion ADCH[4:0] -- ADC Channel Select Bits ADCH4, ADCH3, ADCH2, ADCH1, and ADCH0 form a 5-bit field which is used to select one of 8 ADC channels. The ADC channels are detailed in Table 3-1. NOTE: Take care to prevent switching noise from corrupting the analog signal when simultaneously using a port pin as both an analog and digital input. The ADC subsystem is turned off when the channel select bits are all set to 1. This feature allows for reduced power consumption for the MCU when the ADC is not used. NOTE: Recovery from the disabled state requires one conversion cycle to stabilize. The voltage levels supplied from internal reference nodes as specified in Table 3-1 are used to verify the operation of the ADC both in production test and for user applications. Table 3-1. Mux Channel Select ADCH4 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 ADCH3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 ADCH2 0 0 0 0 1 1 1 1 0 to 0 0 1 1 1 1 1 1 0 0 1 1 0 1 0 1 0 1 Reserved ** Unused * VREFH VREFL ADC power off ADCH1 0 0 1 1 0 0 1 1 0 ADCH0 0 1 0 1 0 1 0 1 0 Unused * Input Select PTB0 PTB1 PTB2 PTB3 PTB4 PTB5 PTB6 PTB7 Freescale Semiconductor, Inc... * If any unused channels are selected, the resulting ADC conversion will be unknown. ** Used for factory testing. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Analog-to-Digital Converter (ADC) Module Data Sheet 55 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module 3.7.2 ADC Data Register High (ADRH) and Data Register Low (ADRL) 3.7.2.1 Left Justified Mode In left justified mode the ADRH register holds the eight MSBs of the 10-bit result. The ADRL register holds the two LSBs of the 10-bit result. All other bits read as 0. ADRH and ADRL are updated each time an ADC single channel conversion completes. Reading ADRH latches the contents of ADRL until ADRL is read. Until ADRL is read, all subsequent results will be lost. Address: $003D Bit 7 Read: Write: Reset: Address: Read: Write: Reset: = Unimplemented Unaffected by reset $003E AD1 AD0 0 0 0 0 0 Unaffected by reset ADRL 0 AD9 6 AD8 5 AD7 4 AD6 3 AD5 2 AD4 1 AD3 ADRH Bit 0 AD2 Freescale Semiconductor, Inc... Figure 3-5. ADC Data Register High (ADRH) and Low (ADRL) 3.7.2.2 Right Justified Mode In right justified mode the ADRH register holds the two MSBs of the 10-bit result. All other bits read as 0. The ADRL register holds the eight LSBs of the 10-bit result. ADRH and ADRL are updated each time an ADC single channel conversion completes. Reading ADRH latches the contents of ADRL until ADRL is read. Until ADRL is read, all subsequent ADC results will be lost. Address: Read: Write: Reset: Address: Read: Write: Reset: = Unimplemented Unaffected by reset $003E AD7 AD6 AD5 AD4 AD3 AD2 AD1 Unaffected by reset ADRL AD0 $003D Bit 7 0 6 0 5 0 4 0 3 0 2 0 1 AD9 ADRH Bit 0 AD8 Figure 3-6. ADC Data Register High (ADRH) and Low (ADRL) Data Sheet 56 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Analog-to-Digital Converter (ADC) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module I/O Registers 3.7.2.3 Left Justified Signed Data Mode In left justified signed data mode the ADRH register holds the eight MSBs of the 10-bit result. The only difference from left justified mode is that the AD9 is complemented. The ADRL register holds the two LSBs of the 10-bit result. All other bits read as 0. ADRH and ADRL are updated each time an ADC single channel conversion completes. Reading ADRH latches the contents of ADRL until ADRL is read. Until ADRL is read, all subsequent results will be lost. Address: Read: Write: Reset: Address: Read: Write: Reset: = Unimplemented Unaffected by reset $003E AD1 AD0 0 0 0 0 0 Unaffected by reset ADRL 0 $003D Bit 7 6 AD8 5 AD7 4 AD6 3 AD5 2 AD4 1 AD3 AD9 ADRH Bit 0 AD2 Freescale Semiconductor, Inc... Figure 3-7. ADC Data Register High (ADRH) and Low (ADRL) 3.7.2.4 Eight Bit Truncation Mode In 8-bit truncation mode the ADRL register holds the eight MSBs of the 10-bit result. The ADRH register is unused and reads as 0. The ADRL register is updated each time an ADC single channel conversion completes. In 8-bit mode, the ADRL register contains no interlocking with ADRH. Address: Read: Write: Reset: Address: Read: Write: Reset: = Unimplemented Unaffected by reset $003E AD9 AD8 AD7 AD6 AD5 AD4 AD3 Unaffected by reset ADRL AD2 $003D Bit 7 0 6 0 5 0 4 0 3 0 2 0 1 0 ADRH Bit 0 0 Figure 3-8. ADC Data Register High (ADRH) and Low (ADRL) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Analog-to-Digital Converter (ADC) Module Data Sheet 57 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module 3.7.3 ADC Clock Register This register selects the clock frequency for the ADC, selecting between modes of operation. Address: Read: Write: Reset: $003F Bit 7 ADIV2 0 Address: 6 ADIV1 0 5 ADIV0 0 4 ADICLK 0 3 MODE1 0 2 MODE0 1 1 R 0 Bit 0 0 0 = Unimplemented Freescale Semiconductor, Inc... Figure 3-9. ADC Clock Register (ADCLK) ADIV2:ADIV0 -- ADC Clock Prescaler Bits ADIV2, ADIV1, and ADIV0 form a 3-bit field which selects the divide ratio used by the ADC to generate the internal ADC clock. Table 3-2 shows the available clock configurations. Table 3-2. ADC Clock Divide Ratio ADIV2 0 0 0 0 1 X = don't care ADIV1 0 0 1 1 X ADIV0 0 1 0 1 X ADC Clock Rate ADC input clock / 1 ADC input clock / 2 ADC input clock / 4 ADC input clock / 8 ADC input clock / 6 ADICLK -- ADC Input Clock Select Bit ADICLK selects either bus clock or CGMXCLK as the input clock source to generate the internal ADC clock. Reset selects CGMXCLK as the ADC clock source. If the external clock (CGMXCLK) is equal to or greater than 1 MHz, CGMXCLK can be used as the clock source for the ADC. If CGMXCLK is less than 1 MHz, use the PLL-generated bus clock as the clock source. As long as the internal ADC clock is at fADIC, correct operation can be guaranteed. See 20.10 Analog-to-Digital Converter (ADC) Characteristics. 1 = Internal bus clock 0 = External clock, CGMXCLK fADIC = CGMXCLK or bus frequency ADIV[2:0] Data Sheet 58 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Analog-to-Digital Converter (ADC) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module I/O Registers MODE1:MODE0 -- Modes of Result Justification Bits MODE1:MODE0 selects among four modes of operation. The manner in which the ADC conversion results will be placed in the ADC data registers is controlled by these modes of operation. Reset returns right-justified mode. 00 = 8-bit truncation mode 01 = Right justified mode 10 = Left justified mode 11 = Left justified sign data mode Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Analog-to-Digital Converter (ADC) Module Data Sheet 59 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Analog-to-Digital Converter (ADC) Module Freescale Semiconductor, Inc... Data Sheet 60 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Analog-to-Digital Converter (ADC) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 4. BEMF Counter Module (BEMF) 4.1 Introduction This section describes the BEMF module. The BEMF counter integrates over time, while the PTD0/TACH0 pin is active. This function is useful for measuring recirculation currents in motors occurring on switching of inductive loads. Freescale Semiconductor, Inc... BEMF is the abbreviation for Back ElectroMagnetic Force. 4.2 Functional Description The 8-bit BEMF counter runs at the internal bus frequency divided by 64. Whenever PTD0/TACH0 is a logic 1, the counter increments by 1 with each period. 4.3 BEMF Register The BEMF register contains the eight read-only bits of the BEMF counter, showing its actual value. A read access to the BEMF register resets all counter bits to 0. Address: Read: Write: Reset: 0 0 = Unimplemented 0 0 0 0 0 0 $000B Bit 7 BEMF7 6 BEMF6 5 BEMF5 4 BEMF4 3 BEMF3 2 BEMF2 1 BEMF1 Bit 0 BEMF0 Figure 4-1. BEMF Register (BEMF) 4.4 Input Signal Port D shares the PTD0/TACH0 pin with the BEMF module. To measure an external signal with the BEMF module, PTD0/TACH0 must be configured as an input (DDRD0 = 0). MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA BEMF Counter Module (BEMF) Data Sheet 61 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. BEMF Counter Module (BEMF) INTERNAL BUS M68HC08 CPU CPU REGISTERS ARITHMETIC/LOGIC UNIT (ALU) SINGLE BREAKPOINT BREAK MODULE PORT A DDRA 5-BIT KEYBOARD INTERRUPT MODULE PTA6/SS PTA5/SPSCK PTA4/KBD4 PTA3/KBD3 PTA2/KBD2 PTA1/KBD1 2-CHANNEL TIMER INTERFACE MODULE A PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PORT B DDRB PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK PTC1/MOSI PTC0/MISO PTD1/TACH1 PTD0/TACH0 PTE1/RxD PTE0/TxD PORT C PORT E PORT D CONTROL AND STATUS REGISTERS 64 BYTES USER FLASH 15,872 BYTES USER RAM 512 BYTES Freescale Semiconductor, Inc... MONITOR ROM 310 BYTES FLASH PROGRAMMING (BURN-IN) ROM 1024 BYTES USER FLASH VECTOR SPACE 36 BYTES 2-CHANNEL TIMER INTERFACE MODULE B ENHANCED SERIAL COMMUNICATION INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE OSC2 OSC1 INTERNAL CLOCK GENERATOR MODULE SERIAL PERIPHERAL INTERFACE MODULE RST 24 INTERNAL SYSTEM INTEGRATION MODULE SINGLE EXTERNAL IRQ MODULE CONFIGURATION REGISTER MODULE PERIODIC WAKEUP TIMEBASE MODULE ARBITER MODULE PRESCALER MODULE IRQ VREFH VDDA VREFL VSSA VDD VSS DDRE DDRD DDRC 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE SECURITY MODULE POWER BEMF MODULE Figure 4-2. Block Diagram Highlighting BEMF Block and Pins Data Sheet 62 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 BEMF Counter Module (BEMF) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. BEMF Counter Module (BEMF) Low Power Modes 4.5 Low Power Modes The WAIT and STOP instructions put the MCU in low power-consumption standby modes. 4.5.1 Wait Mode The BEMF module remains active after execution of the WAIT instruction. In WAIT mode the BEMF register is not accessible by the CPU. 4.5.2 Stop Mode Freescale Semiconductor, Inc... The BEMF module is inactive after execution of the STOP instruction. In STOP mode the BEMF register is not accessible by the CPU. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA BEMF Counter Module (BEMF) Data Sheet 63 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. BEMF Counter Module (BEMF) Freescale Semiconductor, Inc... Data Sheet 64 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 BEMF Counter Module (BEMF) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 5. Configuration Registers (CONFIG1 and CONFIG2) 5.1 Introduction This section describes the configuration registers, CONFIG1 and CONFIG2. The configuration registers control these options: * Stop mode recovery time, 32 CGMXCLK cycles or 4096 CGMXCLK cycles Computer operating properly (COP) timeout period, 218-24 or 213-24 CGMXCLK cycles STOP instruction Computer operating properly (COP) module Low-voltage inhibit (LVI) module control and voltage trip point selection Enable/disable the oscillator (OSC) during stop mode External clock/crystal source control Enhanced SCI clock source selection Freescale Semiconductor, Inc... * * * * * * * 5.2 Functional Description The configuration registers are used in the initialization of various options and can be written once after each reset. All of the configuration register bits are cleared during reset. Since the various options affect the operation of the microcontroller unit (MCU), it is recommended that these registers be written immediately after reset. The configuration registers are located at $001E and $001F. For compatibility, a write to a read-only memory (ROM) version of the MCU at this location will have no effect. The configuration register may be read at anytime. NOTE: The CONFIG module is known as an MOR (mask option register) on a ROM device. On a ROM device, the options are fixed at the time of device fabrication and are neither writable nor changeable by the user. On a FLASH device, the CONFIG registers are special registers containing one-time writable latches after each reset. Upon a reset, the CONFIG registers default to predetermined settings as shown in Figure 5-1 and Figure 5-2. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Configuration Registers (CONFIG1 and CONFIG2) Data Sheet 65 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Configuration Registers (CONFIG1 and CONFIG2) Address: Read: Write: Reset: $001E Bit 7 R 0 R 6 5 4 3 2 1 Bit 0 ESCIBSRC EXTXTALEN EXTSLOW EXTCLKEN TMBCLKSEL OSCENINSTOP SSBPUENB 0 = Reserved 0 0 0 0 0 1 Figure 5-1. Configuration Register 2 (CONFIG2) Address: $001F Bit 7 Read: Write: Reset: COPRS 0 6 LVISTOP 0 5 LVIRSTD 0 4 LVIPWRD 0 3 LVI5OR3(1) 0 2 SSREC 0 1 STOP 0 Bit 0 COPD 0 Freescale Semiconductor, Inc... 1. The LVI5OR3 bit is cleared only by a power-on reset (POR). Figure 5-2. Configuration Register 1 (CONFIG1) ESCIBDSRC -- ESCI Baud Rate Clock Source Bit ESCIBDSRC controls the clock source used for the ESCI. The setting of the bit affects the frequency at which the ESCI operates. 1 = Internal data bus clock used as clock source for ESCI 0 = CGMXCLK used as clock source for ESCI EXTXTALEN -- External Crystal Enable Bit EXTXTALEN enables the external oscillator circuits to be configured for a crystal configuration where the PTC4/OSC1 and PTC3/OSC2 pins are the connections for an external crystal. NOTE: This bit does not function without setting the EXTCLKEN bit also. Clearing the EXTXTALEN bit (default setting) allows the PTC3/OSC2 pin to function as a general-purpose I/O pin. Refer to Table 5-1 for configuration options for the external source. See Section 8. Internal Clock Generator (ICG) Module for a more detailed description of the external clock operation. EXTXTALEN, when set, also configures the clock monitor to expect an external clock source in the valid range of crystals (30 kHz to 100 kHz or 1 MHz to 8 MHz). When EXTXTALEN is clear, the clock monitor will expect an external clock source in the valid range for externally generated clocks when using the clock monitor (60 Hz to 32 MHz). EXTXTALEN, when set, also configures the external clock stabilization divider in the clock monitor for a 4096-cycle timeout to allow the proper stabilization time for a crystal. When EXTXTALEN is clear, the stabilization divider is configured to 16 cycles since an external clock source does not need a startup time. 1 = Allows PTC3/OSC2 to be an external crystal connection. 0 = PTC3/OSC2 functions as an I/O port pin (default). Data Sheet 66 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Configuration Registers (CONFIG1 and CONFIG2) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Configuration Registers (CONFIG1 and CONFIG2) Functional Description EXTSLOW -- Slow External Crystal Enable Bit The EXTSLOW bit has two functions. It configures the ICG module for a fast (1 MHz to 8 MHz) or slow (30 kHz to 100 kHz) speed crystal. The option also configures the clock monitor operation in the ICG module to expect an external frequency higher (307.2 kHz to 32 MHz) or lower (60 Hz to 307.2 kHz) than the base frequency of the internal oscillator. See Section 8. Internal Clock Generator (ICG) Module. 1 = ICG set for slow external crystal operation 0 = ICG set for fast external crystal operation Table 5-1. External Clock Option Settings Freescale Semiconductor, Inc... External Clock Configuration Bits Pin Function Description EXTCLKEN EXTXTALEN PTC4/OSC1 PTC3/OSC2 0 0 0 1 PTC4 PTC4 PTC3 PTC3 Default setting -- external oscillator disabled External oscillator disabled since EXTCLKEN not set External oscillator configured for an external clock source input (square wave) on OSC1 External oscillator configured for an external crystal configuration on OSC1 and OSC2. System will also operate with square-wave clock source in OSC1. 1 0 OSC1 PTC3 1 1 OSC1 OSC2 EXTCLKEN -- External Clock Enable Bit EXTCLKEN enables an external clock source or crystal/ceramic resonator to be used as a clock input. Setting this bit enables PTC4/OSC1 pin to be a clock input pin. Clearing this bit (default setting) allows the PTC4/OSC1 and PTC3/OSC2 pins to function as general-purpose input/output (I/O) pins. Refer to Table 5-1 for configuration options for the external source. See Section 8. Internal Clock Generator (ICG) Module for a more detailed description of the external clock operation. 1 = Allows PTC4/OSC1 to be an external clock connection 0 = PTC4/OSC1 and PTC3/OSC2 function as I/O port pins (default). TMBCLKSEL -- Timebase Clock Select Bit TMBCLKSEL enables an enable the extra divide by 128 prescaler in the timebase module. Setting this bit enables the extra prescaler and clearing this bit disables it. Refer to Table 16-1 for timebase divider selection details. 1 = Enables extra divide by 128 prescaler in timebase module. 0 = Disables extra divide by 128 prescaler in timebase module. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Configuration Registers (CONFIG1 and CONFIG2) Data Sheet 67 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Configuration Registers (CONFIG1 and CONFIG2) OSCENINSTOP -- Oscillator Enable In Stop Mode Bit OSCENINSTOP, when set, will enable the internal clock generator module to continue to generate clocks (either internal, ICLK, or external, ECLK) in stop mode. See Section 8. Internal Clock Generator (ICG) Module. This function is used to keep the timebase running while the rest of the microcontroller stops. When clear, all clock generation will cease and both ICLK and ECLK will be forced low during stop mode. The default state for this option is clear, disabling the ICG in stop mode. 1 = Oscillator enabled to operate during stop mode 0 = Oscillator disabled during stop mode (default) NOTE: Freescale Semiconductor, Inc... This bit has the same functionality as the OSCSTOPENB CONFIG bit in MC68HC908GP20 and MC68HC908GR8 parts. SSBPUENB -- SS Pullup Enable Bit Clearing SSBPUENB enables the SS pullup resistor. 1 = Disables SS pullup resistor. 0 = Enables SS pullup resistor. COPRS -- COP Rate Select Bit COPRS selects the COP timeout period. Reset clears COPRS. See Section 6. Computer Operating Properly (COP) Module. 1 = COP timeout period = 213 - 24 CGMXCLK cycles 0 = COP timeout period = 218 - 24 CGMXCLK cycles LVISTOP -- LVI Enable in Stop Mode Bit When the LVIPWRD bit is clear, setting the LVISTOP bit enables the LVI to operate during stop mode. Reset clears LVISTOP. 1 = LVI enabled during stop mode 0 = LVI disabled during stop mode LVIRSTD -- LVI Reset Disable Bit LVIRSTD disables the reset signal from the LVI module. See Section 11. Low-Voltage Inhibit (LVI) Module. 1 = LVI module resets disabled 0 = LVI module resets enabled LVIPWRD -- LVI Power Disable Bit LVIPWRD disables the LVI module. See Section 11. Low-Voltage Inhibit (LVI) Module. 1 = LVI module power disabled 0 = LVI module power enabled Data Sheet 68 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Configuration Registers (CONFIG1 and CONFIG2) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Configuration Registers (CONFIG1 and CONFIG2) Functional Description LVI5OR3 -- LVI 5-V or 3-V Operating Mode Bit LVI5OR3 selects the voltage operating mode of the LVI module. See Section 11. Low-Voltage Inhibit (LVI) Module. The voltage mode selected for the LVI will typically be 5 V. However, users may choose to operate the LVI in 3-V mode if desired. See Section 20. Electrical Specifications for the LVI's voltage trip points for each of the modes. 1 = LVI operates in 5-V mode. 0 = LVI operates in 3-V mode. NOTE: The LVI5OR3 bit is cleared by a power-on reset (POR) only. Other resets will leave this bit unaffected. SSREC -- Short Stop Recovery Bit SSREC enables the CPU to exit stop mode with a delay of 32 CGMXCLK cycles instead of a 4096-CGMXCLK cycle delay. 1 = Stop mode recovery after 32 CGMXCLK cycles 0 = Stop mode recovery after 4096 CGMXCLCK cycles NOTE: Exiting stop mode by an LVI reset will result in the long stop recovery. If the system clock source selected is the internal oscillator or the external crystal and the OSCENINSTOP configuration bit is not set, the oscillator will be disabled during stop mode. The short stop recovery does not provide enough time for oscillator stabilization and thus the SSREC bit should not be set. When using the LVI during normal operation but disabling during stop mode, the LVI will have an enable time of tEN. The system stabilization time for power-on reset and long stop recovery (both 4096 CGMXCLK cycles) gives a delay longer than the LVI enable time for these startup scenarios. There is no period where the MCU is not protected from a low-power condition. However, when using the short stop recovery configuration option, the 32-CGMXCLK delay must be greater than the LVI's turn on time to avoid a period in startup where the LVI is not protecting the MCU. STOP -- STOP Instruction Enable Bit STOP enables the STOP instruction. 1 = STOP instruction enabled 0 = STOP instruction treated as illegal opcode COPD -- COP Disable Bit COPD disables the COP module. See Section 6. Computer Operating Properly (COP) Module. 1 = COP module disabled 0 = COP module enabled Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Configuration Registers (CONFIG1 and CONFIG2) Data Sheet 69 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Configuration Registers (CONFIG1 and CONFIG2) Freescale Semiconductor, Inc... Data Sheet 70 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Configuration Registers (CONFIG1 and CONFIG2) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 6. Computer Operating Properly (COP) Module 6.1 Introduction The computer operating properly (COP) module contains a free-running counter that generates a reset if allowed to overflow. The COP module helps software recover from runaway code. Prevent a COP reset by periodically clearing the COP counter. Freescale Semiconductor, Inc... 6.2 Functional Description SIM MODULE BUSCLKX4 12-BIT SIM COUNTER SIM RESET CIRCUIT RESET STATUS REGISTER CLEAR ALL STAGES CLEAR STAGES 5-12 INTERNAL RESET SOURCES(1) RESET VECTOR FETCH COPCTL WRITE COP CLOCK COP MODULE 6-BIT COP COUNTER COPEN (FROM SIM) COPD (FROM CONFIG1) RESET COPCTL WRITE COP RATE SELECT (COPRS FROM CONFIG1) CLEAR COP COUNTER 1. See Section 14. System Integration Module (SIM) for more details. Figure 6-1. COP Block Diagram MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Computer Operating Properly (COP) Module COP TIMEOUT Data Sheet 71 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Computer Operating Properly (COP) Module The COP counter is a free-running 6-bit counter preceded by a 12-bit prescaler. If not cleared by software, the COP counter overflows and generates an asynchronous reset after 213 - 24 or 218 - 24 CGMXCLK cycles, depending on the state of the COP rate select bit, COPRS, in the CONFIG-1. When COPRS = 0, a 4.9152-MHz crystal gives a COP timeout period of 53.3 ms. Writing any value to location $FFFF before an overflow occurs prevents a COP reset by clearing the COP counter and stages 4-12 of the SIM counter. NOTE: Service the COP immediately after reset and before entering or after exiting stop mode to guarantee the maximum time before the first COP counter overflow. A COP reset pulls the RST pin low for 32 CGMXCLK cycles and sets the COP bit in the reset status register (RSR). In monitor mode, the COP is disabled if the RST pin or the IRQ pin is held at VTST. During the break state, VTST on the RST pin disables the COP. NOTE: Place COP clearing instructions in the main program and not in an interrupt subroutine. Such an interrupt subroutine could keep the COP from generating a reset even while the main program is not working properly. Freescale Semiconductor, Inc... 6.3 I/O Signals The following paragraphs describe the signals shown in Figure 6-1. 6.3.1 CGMXCLK CGMXCLK is the crystal oscillator output signal. CGMXCLK frequency is equal to the crystal frequency. 6.3.2 STOP Instruction The STOP instruction signal clears the COP prescaler. 6.3.3 COPCTL Write Writing any value to the COP control register (COPCTL) (see 6.4 COP Control Register) clears the COP counter and clears stages 12 through 4 of the COP prescaler. Reading the COP control register returns the reset vector. 6.3.4 Power-On Reset The power-on reset (POR) circuit clears the COP prescaler 4096 CGMXCLK cycles after power-up. 6.3.5 Internal Reset An internal reset clears the COP prescaler and the COP counter. Data Sheet 72 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Computer Operating Properly (COP) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Computer Operating Properly (COP) Module COP Control Register 6.3.6 Reset Vector Fetch A reset vector fetch occurs when the vector address appears on the data bus. A reset vector fetch clears the COP prescaler. 6.3.7 COPD The COPD signal reflects the state of the COP disable bit (COPD) in the configuration register. See Section 5. Configuration Registers (CONFIG1 and CONFIG2). 6.3.8 COPRS Freescale Semiconductor, Inc... The COPRS signal reflects the state of the COP rate select bit (COPRS) in the configuration register. See Section 5. Configuration Registers (CONFIG1 and CONFIG2). 6.4 COP Control Register The COP control register is located at address $FFFF and overlaps the reset vector. Writing any value to $FFFF clears the COP counter and starts a new timeout period. Reading location $FFFF returns the low byte of the reset vector. Address: Read: Write: Reset: $FFFF Bit 7 6 5 4 3 2 1 Bit 0 Low byte of reset vector Clear COP counter Unaffected by reset Figure 6-2. COP Control Register (COPCTL) 6.5 Interrupts The COP does not generate CPU interrupt requests. 6.6 Monitor Mode The COP is disabled in monitor mode when VDD = VTST is present on the IRQ pin or on the RST pin. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Computer Operating Properly (COP) Module Data Sheet 73 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Computer Operating Properly (COP) Module 6.7 Low-Power Modes The WAIT and STOP instructions put the MCU in low power-consumption standby modes. 6.7.1 Wait Mode The COP remains active in wait mode. To prevent a COP reset during wait mode, periodically clear the COP counter in a CPU interrupt routine. 6.7.2 Stop Mode Freescale Semiconductor, Inc... Stop mode turns off the CGMXCLK input to the COP and clears the COP prescaler. Service the COP immediately before entering or after exiting stop mode to ensure a full COP timeout period after entering or exiting stop mode. The STOP bit in the configuration register (CONFIG) enables the STOP instruction. To prevent inadvertently turning off the COP with a STOP instruction, disable the STOP instruction by clearing the STOP bit. 6.8 COP Module During Break Interrupts The COP is disabled during a break interrupt when VTST is present on the RST pin. Data Sheet 74 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Computer Operating Properly (COP) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 7. Central Processor Unit (CPU) 7.1 Introduction The M68HC08 CPU (central processor unit) is an enhanced and fully object-code-compatible version of the M68HC05 CPU. The CPU08 Reference Manual (Motorola document order number CPU08RM/AD) contains a description of the CPU instruction set, addressing modes, and architecture. Freescale Semiconductor, Inc... 7.2 Features Features of the CPU include: * * * * * * * * * * * Object code fully upward-compatible with M68HC05 Family 16-bit stack pointer with stack manipulation instructions 16-bit index register with x-register manipulation instructions 8-MHz CPU internal bus frequency 64-Kbyte program/data memory space 16 addressing modes Memory-to-memory data moves without using accumulator Fast 8-bit by 8-bit multiply and 16-bit by 8-bit divide instructions Enhanced binary-coded decimal (BCD) data handling Modular architecture with expandable internal bus definition for extension of addressing range beyond 64 Kbytes Low-power stop and wait modes MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Central Processor Unit (CPU) Data Sheet 75 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Central Processor Unit (CPU) 7.3 CPU Registers Figure 7-1 shows the five CPU registers. CPU registers are not part of the memory map. 7 15 H 15 15 X 0 STACK POINTER (SP) 0 PROGRAM COUNTER (PC) 7 0 V11HINZC CONDITION CODE REGISTER (CCR) 0 ACCUMULATOR (A) 0 INDEX REGISTER (H:X) Freescale Semiconductor, Inc... CARRY/BORROW FLAG ZERO FLAG NEGATIVE FLAG INTERRUPT MASK HALF-CARRY FLAG TWO'S COMPLEMENT OVERFLOW FLAG Figure 7-1. CPU Registers 7.3.1 Accumulator The accumulator is a general-purpose 8-bit register. The CPU uses the accumulator to hold operands and the results of arithmetic/logic operations. Bit 7 Read: Write: Reset: Unaffected by reset 6 5 4 3 2 1 Bit 0 Figure 7-2. Accumulator (A) Data Sheet 76 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Central Processor Unit (CPU) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Central Processor Unit (CPU) CPU Registers 7.3.2 Index Register The 16-bit index register allows indexed addressing of a 64-Kbyte memory space. H is the upper byte of the index register, and X is the lower byte. H:X is the concatenated 16-bit index register. In the indexed addressing modes, the CPU uses the contents of the index register to determine the conditional address of the operand. The index register can serve also as a temporary data storage location. Bit 15 Read: Write: Reset: 0 0 0 0 0 0 0 0 X X X X X X X X Bit 0 Freescale Semiconductor, Inc... 14 13 12 11 10 9 8 7 6 5 4 3 2 1 X = Indeterminate Figure 7-3. Index Register (H:X) 7.3.3 Stack Pointer The stack pointer is a 16-bit register that contains the address of the next location on the stack. During a reset, the stack pointer is preset to $00FF. The reset stack pointer (RSP) instruction sets the least significant byte to $FF and does not affect the most significant byte. The stack pointer decrements as data is pushed onto the stack and increments as data is pulled from the stack. In the stack pointer 8-bit offset and 16-bit offset addressing modes, the stack pointer can function as an index register to access data on the stack. The CPU uses the contents of the stack pointer to determine the conditional address of the operand. Bit 15 Read: Write: Reset: 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Bit 0 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Figure 7-4. Stack Pointer (SP) NOTE: The location of the stack is arbitrary and may be relocated anywhere in random-access memory (RAM). Moving the SP out of page 0 ($0000 to $00FF) frees direct address (page 0) space. For correct operation, the stack pointer must point only to RAM locations. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Central Processor Unit (CPU) Data Sheet 77 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Central Processor Unit (CPU) 7.3.4 Program Counter The program counter is a 16-bit register that contains the address of the next instruction or operand to be fetched. Normally, the program counter automatically increments to the next sequential memory location every time an instruction or operand is fetched. Jump, branch, and interrupt operations load the program counter with an address other than that of the next sequential location. During reset, the program counter is loaded with the reset vector address located at $FFFE and $FFFF. The vector address is the address of the first instruction to be executed after exiting the reset state. Bit 15 Read: Write: Reset: Loaded with vector from $FFFE and $FFFF Bit 0 Freescale Semiconductor, Inc... 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Figure 7-5. Program Counter (PC) 7.3.5 Condition Code Register The 8-bit condition code register contains the interrupt mask and five flags that indicate the results of the instruction just executed. Bits 6 and 5 are set permanently to 1. The following paragraphs describe the functions of the condition code register. Bit 7 Read: V Write: Reset: X X = Indeterminate 1 1 X 1 X X X 1 1 H I N Z C 6 5 4 3 2 1 Bit 0 Figure 7-6. Condition Code Register (CCR) V -- Overflow Flag The CPU sets the overflow flag when a two's complement overflow occurs. The signed branch instructions BGT, BGE, BLE, and BLT use the overflow flag. 1 = Overflow 0 = No overflow Data Sheet 78 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Central Processor Unit (CPU) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Central Processor Unit (CPU) CPU Registers H -- Half-Carry Flag The CPU sets the half-carry flag when a carry occurs between accumulator bits 3 and 4 during an add-without-carry (ADD) or add-with-carry (ADC) operation. The half-carry flag is required for binary-coded decimal (BCD) arithmetic operations. The DAA instruction uses the states of the H and C flags to determine the appropriate correction factor. 1 = Carry between bits 3 and 4 0 = No carry between bits 3 and 4 I -- Interrupt Mask When the interrupt mask is set, all maskable CPU interrupts are disabled. CPU interrupts are enabled when the interrupt mask is cleared. When a CPU interrupt occurs, the interrupt mask is set automatically after the CPU registers are saved on the stack, but before the interrupt vector is fetched. 1 = Interrupts disabled 0 = Interrupts enabled NOTE: To maintain M6805 Family compatibility, the upper byte of the index register (H) is not stacked automatically. If the interrupt service routine modifies H, then the user must stack and unstack H using the PSHH and PULH instructions. After the I bit is cleared, the highest-priority interrupt request is serviced first. A return-from-interrupt (RTI) instruction pulls the CPU registers from the stack and restores the interrupt mask from the stack. After any reset, the interrupt mask is set and can be cleared only by the clear interrupt mask software instruction (CLI). N -- Negative flag The CPU sets the negative flag when an arithmetic operation, logic operation, or data manipulation produces a negative result, setting bit 7 of the result. 1 = Negative result 0 = Non-negative result Z -- Zero flag The CPU sets the zero flag when an arithmetic operation, logic operation, or data manipulation produces a result of $00. 1 = Zero result 0 = Non-zero result C -- Carry/Borrow Flag The CPU sets the carry/borrow flag when an addition operation produces a carry out of bit 7 of the accumulator or when a subtraction operation requires a borrow. Some instructions -- such as bit test and branch, shift, and rotate -- also clear or set the carry/borrow flag. 1 = Carry out of bit 7 0 = No carry out of bit 7 Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Central Processor Unit (CPU) Data Sheet 79 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Central Processor Unit (CPU) 7.4 Arithmetic/Logic Unit (ALU) The ALU performs the arithmetic and logic operations defined by the instruction set. Refer to the CPU08 Reference Manual (Motorola document order number CPU08RM/AD) for a description of the instructions and addressing modes and more detail about the architecture of the CPU. 7.5 Low-Power Modes Freescale Semiconductor, Inc... The WAIT and STOP instructions put the MCU in low power-consumption standby modes. 7.5.1 Wait Mode The WAIT instruction: * Clears the interrupt mask (I bit) in the condition code register, enabling interrupts. After exit from wait mode by interrupt, the I bit remains clear. After exit by reset, the I bit is set. Disables the CPU clock * 7.5.2 Stop Mode The STOP instruction: * Clears the interrupt mask (I bit) in the condition code register, enabling external interrupts. After exit from stop mode by external interrupt, the I bit remains clear. After exit by reset, the I bit is set. Disables the CPU clock * After exiting stop mode, the CPU clock begins running after the oscillator stabilization delay. 7.6 CPU During Break Interrupts If a break module is present on the MCU, the CPU starts a break interrupt by: * * Loading the instruction register with the SWI instruction Loading the program counter with $FFFC:$FFFD or with $FEFC:$FEFD in monitor mode The break interrupt begins after completion of the CPU instruction in progress. If the break address register match occurs on the last cycle of a CPU instruction, the break interrupt begins immediately. A return-from-interrupt instruction (RTI) in the break routine ends the break interrupt and returns the MCU to normal operation if the break interrupt has been deasserted. Data Sheet 80 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Central Processor Unit (CPU) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Central Processor Unit (CPU) Instruction Set Summary 7.7 Instruction Set Summary Table 7-1 provides a summary of the M68HC08 instruction set. Table 7-1. Instruction Set Summary (Sheet 1 of 7) Opcode Source Form ADC #opr ADC opr ADC opr ADC opr,X ADC opr,X ADC ,X ADC opr,SP ADC opr,SP ADD #opr ADD opr ADD opr ADD opr,X ADD opr,X ADD ,X ADD opr,SP ADD opr,SP AIS #opr AIX #opr AND #opr AND opr AND opr AND opr,X AND opr,X AND ,X AND opr,SP AND opr,SP ASL opr ASLA ASLX ASL opr,X ASL ,X ASL opr,SP ASR opr ASRA ASRX ASR opr,X ASR opr,X ASR opr,SP BCC rel Operation Description VH I NZC Add with Carry A (A) + (M) + (C) - Freescale Semiconductor, Inc... IMM DIR EXT IX2 IX1 IX SP1 SP2 IMM DIR EXT IX2 IX1 IX SP1 SP2 A9 B9 C9 D9 E9 F9 9EE9 9ED9 AB BB CB DB EB FB 9EEB 9EDB A7 AF A4 B4 C4 D4 E4 F4 9EE4 9ED4 ii dd hh ll ee ff ff ff ee ff ii dd hh ll ee ff ff ff ee ff ii ii ii dd hh ll ee ff ff ff ee ff Add without Carry A (A) + (M) - Add Immediate Value (Signed) to SP Add Immediate Value (Signed) to H:X SP (SP) + (16 M) H:X (H:X) + (16 M) - - - - - - IMM - - - - - - IMM IMM DIR EXT - IX2 IX1 IX SP1 SP2 DIR INH INH IX1 IX SP1 DIR INH INH IX1 IX SP1 Logical AND A (A) & (M) 0-- Arithmetic Shift Left (Same as LSL) C b7 b0 0 -- 38 dd 48 58 68 ff 78 9E68 ff 37 dd 47 57 67 ff 77 9E67 ff 24 11 13 15 17 19 1B 1D 1F 25 27 rr dd dd dd dd dd dd dd dd rr rr Arithmetic Shift Right b7 b0 C -- Branch if Carry Bit Clear PC (PC) + 2 + rel ? (C) = 0 - - - - - - REL DIR (b0) DIR (b1) DIR (b2) DIR (b3) - - - - - - DIR (b4) DIR (b5) DIR (b6) DIR (b7) - - - - - - REL - - - - - - REL BCLR n, opr Clear Bit n in M Mn 0 BCS rel BEQ rel Branch if Carry Bit Set (Same as BLO) Branch if Equal PC (PC) + 2 + rel ? (C) = 1 PC (PC) + 2 + rel ? (Z) = 1 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Central Processor Unit (CPU) Data Sheet 81 For More Information On This Product, Go to: www.freescale.com Cycles 2 3 4 4 3 2 4 5 2 3 4 4 3 2 4 5 2 2 2 3 4 4 3 2 4 5 4 1 1 4 3 5 4 1 1 4 3 5 3 4 4 4 4 4 4 4 4 3 3 Effect on CCR Operand Address Mode Freescale Semiconductor, Inc. Central Processor Unit (CPU) Table 7-1. Instruction Set Summary (Sheet 2 of 7) Address Mode Opcode Source Form BGE opr BGT opr BHCC rel BHCS rel Operation Description VH I NZC Branch if Greater Than or Equal To (Signed Operands) Branch if Greater Than (Signed Operands) Branch if Half Carry Bit Clear Branch if Half Carry Bit Set Branch if Higher Branch if Higher or Same (Same as BCC) Branch if IRQ Pin High Branch if IRQ Pin Low PC (PC) + 2 + rel ? (N V) = 0 - - - - - - REL 90 92 28 29 22 24 2F 2E A5 B5 C5 D5 E5 F5 9EE5 9ED5 93 25 23 91 2C 2B 2D 26 2A 20 01 03 05 07 09 0B 0D 0F 21 rr rr rr rr rr rr rr rr ii dd hh ll ee ff ff ff ee ff rr rr rr rr rr rr rr rr rr rr dd rr dd rr dd rr dd rr dd rr dd rr dd rr dd rr rr PC (PC) + 2 + rel ? (Z) | (N V) = 0 - - - - - - REL PC (PC) + 2 + rel ? (H) = 0 PC (PC) + 2 + rel ? (H) = 1 PC (PC) + 2 + rel ? (C) | (Z) = 0 PC (PC) + 2 + rel ? (C) = 0 PC (PC) + 2 + rel ? IRQ = 1 PC (PC) + 2 + rel ? IRQ = 0 - - - - - - REL - - - - - - REL - - - - - - REL - - - - - - REL - - - - - - REL - - - - - - REL IMM DIR EXT IX2 - IX1 IX SP1 SP2 3 3 3 3 3 2 3 4 4 3 2 4 5 3 3 3 3 3 3 3 3 3 3 5 5 5 5 5 5 5 5 3 Freescale Semiconductor, Inc... BHI rel BHS rel BIH rel BIL rel BIT #opr BIT opr BIT opr BIT opr,X BIT opr,X BIT ,X BIT opr,SP BIT opr,SP BLE opr BLO rel BLS rel BLT opr BMC rel BMI rel BMS rel BNE rel BPL rel BRA rel Bit Test (A) & (M) 0-- Branch if Less Than or Equal To (Signed Operands) Branch if Lower (Same as BCS) Branch if Lower or Same Branch if Less Than (Signed Operands) Branch if Interrupt Mask Clear Branch if Minus Branch if Interrupt Mask Set Branch if Not Equal Branch if Plus Branch Always PC (PC) + 2 + rel ? (Z) | (N V) = 1 - - - - - - REL PC (PC) + 2 + rel ? (C) = 1 PC (PC) + 2 + rel ? (C) | (Z) = 1 PC (PC) + 2 + rel ? (N V) =1 PC (PC) + 2 + rel ? (I) = 0 PC (PC) + 2 + rel ? (N) = 1 PC (PC) + 2 + rel ? (I) = 1 PC (PC) + 2 + rel ? (Z) = 0 PC (PC) + 2 + rel ? (N) = 0 PC (PC) + 2 + rel - - - - - - REL - - - - - - REL - - - - - - REL - - - - - - REL - - - - - - REL - - - - - - REL - - - - - - REL - - - - - - REL - - - - - - REL DIR (b0) DIR (b1) DIR (b2) DIR (b3) DIR (b4) DIR (b5) DIR (b6) DIR (b7) BRCLR n,opr,rel Branch if Bit n in M Clear PC (PC) + 3 + rel ? (Mn) = 0 ----- BRN rel Branch Never PC (PC) + 2 - - - - - - REL Data Sheet 82 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Central Processor Unit (CPU) MOTOROLA For More Information On This Product, Go to: www.freescale.com Cycles 3 3 3 Effect on CCR Operand Freescale Semiconductor, Inc. Central Processor Unit (CPU) Instruction Set Summary Table 7-1. Instruction Set Summary (Sheet 3 of 7) Address Mode Opcode Source Form Operation Description Cycles 5 5 5 5 5 5 5 5 4 4 4 4 4 4 4 4 4 5 4 4 5 4 6 1 2 3 1 1 1 3 2 4 2 3 4 4 3 2 4 5 4 1 1 4 3 5 3 4 Effect on CCR VH I NZC BRSET n,opr,rel Branch if Bit n in M Set PC (PC) + 3 + rel ? (Mn) = 1 ----- DIR (b0) DIR (b1) DIR (b2) DIR (b3) DIR (b4) DIR (b5) DIR (b6) DIR (b7) 00 02 04 06 08 0A 0C 0E 10 12 14 16 18 1A 1C 1E dd rr dd rr dd rr dd rr dd rr dd rr dd rr dd rr dd dd dd dd dd dd dd dd Freescale Semiconductor, Inc... BSET n,opr Set Bit n in M Mn 1 DIR (b0) DIR (b1) DIR (b2) DIR (b3) ------ DIR (b4) DIR (b5) DIR (b6) DIR (b7) BSR rel Branch to Subroutine PC (PC) + 2; push (PCL) SP (SP) - 1; push (PCH) SP (SP) - 1 PC (PC) + rel PC (PC) + 3 + rel ? (A) - (M) = $00 PC (PC) + 3 + rel ? (A) - (M) = $00 PC (PC) + 3 + rel ? (X) - (M) = $00 PC (PC) + 3 + rel ? (A) - (M) = $00 PC (PC) + 2 + rel ? (A) - (M) = $00 PC (PC) + 4 + rel ? (A) - (M) = $00 C0 I0 M $00 A $00 X $00 H $00 M $00 M $00 M $00 - - - - - - REL AD rr CBEQ opr,rel CBEQA #opr,rel CBEQX #opr,rel CBEQ opr,X+,rel Compare and Branch if Equal CBEQ X+,rel CBEQ opr,SP,rel CLC CLI CLR opr CLRA CLRX CLRH CLR opr,X CLR ,X CLR opr,SP CMP #opr CMP opr CMP opr CMP opr,X CMP opr,X CMP ,X CMP opr,SP CMP opr,SP COM opr COMA COMX COM opr,X COM ,X COM opr,SP CPHX #opr CPHX opr Clear Carry Bit Clear Interrupt Mask DIR IMM IMM - - - - - - IX1+ IX+ SP1 - - - - - 0 INH - - 0 - - - INH DIR INH INH 0 - - 0 1 - INH IX1 IX SP1 IMM DIR EXT IX2 IX1 IX SP1 SP2 DIR INH INH 1 IX1 IX SP1 IMM DIR 31 41 51 61 71 9E61 98 9A dd rr ii rr ii rr ff rr rr ff rr Clear 3F dd 4F 5F 8C 6F ff 7F 9E6F ff A1 B1 C1 D1 E1 F1 9EE1 9ED1 ii dd hh ll ee ff ff ff ee ff Compare A with M (A) - (M) -- Complement (One's Complement) M (M) = $FF - (M) A (A) = $FF - (M) X (X) = $FF - (M) M (M) = $FF - (M) M (M) = $FF - (M) M (M) = $FF - (M) (H:X) - (M:M + 1) 0-- 33 dd 43 53 63 ff 73 9E63 ff 65 75 ii ii+1 dd Compare H:X with M -- MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Central Processor Unit (CPU) Data Sheet 83 For More Information On This Product, Go to: www.freescale.com Operand Freescale Semiconductor, Inc. Central Processor Unit (CPU) Table 7-1. Instruction Set Summary (Sheet 4 of 7) Address Mode Opcode Source Form CPX #opr CPX opr CPX opr CPX ,X CPX opr,X CPX opr,X CPX opr,SP CPX opr,SP DAA Operation Description VH I NZC Compare X with M (X) - (M) -- IMM DIR EXT IX2 IX1 IX SP1 SP2 INH A3 B3 C3 D3 E3 F3 9EE3 9ED3 72 3B 4B 5B 6B 7B 9E6B ii dd hh ll ee ff ff ff ee ff Decimal Adjust A (A)10 U-- Freescale Semiconductor, Inc... DBNZ opr,rel DBNZA rel DBNZX rel Decrement and Branch if Not Zero DBNZ opr,X,rel DBNZ X,rel DBNZ opr,SP,rel DEC opr DECA DECX DEC opr,X DEC ,X DEC opr,SP DIV EOR #opr EOR opr EOR opr EOR opr,X EOR opr,X EOR ,X EOR opr,SP EOR opr,SP INC opr INCA INCX INC opr,X INC ,X INC opr,SP JMP opr JMP opr JMP opr,X JMP opr,X JMP ,X JSR opr JSR opr JSR opr,X JSR opr,X JSR ,X LDA #opr LDA opr LDA opr LDA opr,X LDA opr,X LDA ,X LDA opr,SP LDA opr,SP A (A) - 1 or M (M) - 1 or X (X) - 1 PC (PC) + 3 + rel ? (result) 0 DIR PC (PC) + 2 + rel ? (result) 0 INH PC (PC) + 2 + rel ? (result) 0 - - - - - - INH PC (PC) + 3 + rel ? (result) 0 IX1 PC (PC) + 2 + rel ? (result) 0 IX PC (PC) + 4 + rel ? (result) 0 SP1 M (M) - 1 A (A) - 1 X (X) - 1 M (M) - 1 M (M) - 1 M (M) - 1 A (H:A)/(X) H Remainder DIR INH INH - IX1 IX SP1 INH IMM DIR EXT - IX2 IX1 IX SP1 SP2 DIR INH INH - IX1 IX SP1 dd rr rr rr ff rr rr ff rr Decrement -- 3A dd 4A 5A 6A ff 7A 9E6A ff 52 A8 B8 C8 D8 E8 F8 9EE8 9ED8 ii dd hh ll ee ff ff ff ee ff Divide ---- Exclusive OR M with A A (A M) 0-- Increment M (M) + 1 A (A) + 1 X (X) + 1 M (M) + 1 M (M) + 1 M (M) + 1 -- 3C dd 4C 5C 6C ff 7C 9E6C ff BC CC DC EC FC BD CD DD ED FD A6 B6 C6 D6 E6 F6 9EE6 9ED6 dd hh ll ee ff ff dd hh ll ee ff ff ii dd hh ll ee ff ff ff ee ff Jump PC Jump Address DIR EXT - - - - - - IX2 IX1 IX DIR EXT - - - - - - IX2 IX1 IX IMM DIR EXT IX2 - IX1 IX SP1 SP2 Jump to Subroutine PC (PC) + n (n = 1, 2, or 3) Push (PCL); SP (SP) - 1 Push (PCH); SP (SP) - 1 PC Unconditional Address Load A from M A (M) 0-- Data Sheet 84 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Central Processor Unit (CPU) MOTOROLA For More Information On This Product, Go to: www.freescale.com Cycles 2 3 4 4 3 2 4 5 2 5 3 3 5 4 6 4 1 1 4 3 5 7 2 3 4 4 3 2 4 5 4 1 1 4 3 5 2 3 4 3 2 4 5 6 5 4 2 3 4 4 3 2 4 5 Effect on CCR Operand Freescale Semiconductor, Inc. Central Processor Unit (CPU) Instruction Set Summary Table 7-1. Instruction Set Summary (Sheet 5 of 7) Address Mode Opcode Source Form LDHX #opr LDHX opr LDX #opr LDX opr LDX opr LDX opr,X LDX opr,X LDX ,X LDX opr,SP LDX opr,SP LSL opr LSLA LSLX LSL opr,X LSL ,X LSL opr,SP LSR opr LSRA LSRX LSR opr,X LSR ,X LSR opr,SP MOV opr,opr MOV opr,X+ MOV #opr,opr MOV X+,opr MUL NEG opr NEGA NEGX NEG opr,X NEG ,X NEG opr,SP NOP NSA ORA #opr ORA opr ORA opr ORA opr,X ORA opr,X ORA ,X ORA opr,SP ORA opr,SP PSHA PSHH PSHX PULA PULH PULX Operation Description VH I NZC Load H:X from M H:X (M:M + 1) 0-- - IMM DIR 45 55 AE BE CE DE EE FE 9EEE 9EDE ii jj dd ii dd hh ll ee ff ff ff ee ff Load X from M X (M) 0-- Freescale Semiconductor, Inc... IMM DIR EXT IX2 - IX1 IX SP1 SP2 DIR INH INH IX1 IX SP1 DIR INH INH IX1 IX SP1 DD - DIX+ IMD IX+D Logical Shift Left (Same as ASL) C b7 b0 0 -- 38 dd 48 58 68 ff 78 9E68 ff 34 dd 44 54 64 ff 74 9E64 ff 4E 5E 6E 7E 42 30 dd 40 50 60 ff 70 9E60 ff 9D 62 AA BA CA DA EA FA 9EEA 9EDA 87 8B 89 86 8A 88 ii dd hh ll ee ff ff ff ee ff dd dd dd ii dd dd Logical Shift Right 0 b7 b0 C --0 Move (M)Destination (M)Source H:X (H:X) + 1 (IX+D, DIX+) X:A (X) x (A) M -(M) = $00 - (M) A -(A) = $00 - (A) X -(X) = $00 - (X) M -(M) = $00 - (M) M -(M) = $00 - (M) None A (A[3:0]:A[7:4]) 0-- Unsigned multiply - 0 - - - 0 INH DIR INH INH IX1 IX SP1 Negate (Two's Complement) -- No Operation Nibble Swap A - - - - - - INH - - - - - - INH IMM DIR EXT IX2 - IX1 IX SP1 SP2 Inclusive OR A and M A (A) | (M) 0-- Push A onto Stack Push H onto Stack Push X onto Stack Pull A from Stack Pull H from Stack Pull X from Stack Push (A); SP (SP) - 1 Push (H); SP (SP) - 1 Push (X); SP (SP) - 1 SP (SP + 1); Pull (A) SP (SP + 1); Pull (H) SP (SP + 1); Pull (X) - - - - - - INH - - - - - - INH - - - - - - INH - - - - - - INH - - - - - - INH - - - - - - INH MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Central Processor Unit (CPU) Data Sheet 85 For More Information On This Product, Go to: www.freescale.com Cycles 3 4 2 3 4 4 3 2 4 5 4 1 1 4 3 5 4 1 1 4 3 5 5 4 4 4 5 4 1 1 4 3 5 1 3 2 3 4 4 3 2 4 5 2 2 2 2 2 2 Effect on CCR Operand Freescale Semiconductor, Inc. Central Processor Unit (CPU) Table 7-1. Instruction Set Summary (Sheet 6 of 7) Address Mode Opcode Source Form ROL opr ROLA ROLX ROL opr,X ROL ,X ROL opr,SP ROR opr RORA RORX ROR opr,X ROR ,X ROR opr,SP RSP Operation Description VH I NZC Rotate Left through Carry C b7 b0 -- DIR INH INH IX1 IX SP1 DIR INH INH IX1 IX SP1 39 dd 49 59 69 ff 79 9E69 ff 36 dd 46 56 66 ff 76 9E66 ff 9C Rotate Right through Carry b7 b0 C -- Freescale Semiconductor, Inc... Reset Stack Pointer SP $FF SP (SP) + 1; Pull (CCR) SP (SP) + 1; Pull (A) SP (SP) + 1; Pull (X) SP (SP) + 1; Pull (PCH) SP (SP) + 1; Pull (PCL) SP SP + 1; Pull (PCH) SP SP + 1; Pull (PCL) - - - - - - INH RTI Return from Interrupt INH 80 RTS SBC #opr SBC opr SBC opr SBC opr,X SBC opr,X SBC ,X SBC opr,SP SBC opr,SP SEC SEI STA opr STA opr STA opr,X STA opr,X STA ,X STA opr,SP STA opr,SP STHX opr STOP STX opr STX opr STX opr,X STX opr,X STX ,X STX opr,SP STX opr,SP SUB #opr SUB opr SUB opr SUB opr,X SUB opr,X SUB ,X SUB opr,SP SUB opr,SP Return from Subroutine - - - - - - INH IMM DIR EXT IX2 IX1 IX SP1 SP2 81 A2 B2 C2 D2 E2 F2 9EE2 9ED2 99 9B B7 C7 D7 E7 F7 9EE7 9ED7 35 8E BF CF DF EF FF 9EEF 9EDF A0 B0 C0 D0 E0 F0 9EE0 9ED0 dd hh ll ee ff ff ff ee ff ii dd hh ll ee ff ff ff ee ff dd hh ll ee ff ff ff ee ff dd ii dd hh ll ee ff ff ff ee ff Subtract with Carry A (A) - (M) - (C) -- Set Carry Bit Set Interrupt Mask C1 I1 - - - - - 1 INH - - 1 - - - INH DIR EXT IX2 - IX1 IX SP1 SP2 - DIR Store A in M M (A) 0-- Store H:X in M Enable IRQ Pin; Stop Oscillator (M:M + 1) (H:X) I 0; Stop Oscillator 0-- - - 0 - - - INH DIR EXT IX2 - IX1 IX SP1 SP2 IMM DIR EXT IX2 IX1 IX SP1 SP2 Store X in M M (X) 0-- Subtract A (A) - (M) -- Data Sheet 86 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Central Processor Unit (CPU) MOTOROLA For More Information On This Product, Go to: www.freescale.com Cycles 4 1 1 4 3 5 4 1 1 4 3 5 1 7 4 2 3 4 4 3 2 4 5 1 2 3 4 4 3 2 4 5 4 1 3 4 4 3 2 4 5 2 3 4 4 3 2 4 5 Effect on CCR Operand Freescale Semiconductor, Inc. Central Processor Unit (CPU) Opcode Map Table 7-1. Instruction Set Summary (Sheet 7 of 7) Address Mode Opcode Source Form Operation Description PC (PC) + 1; Push (PCL) SP (SP) - 1; Push (PCH) SP (SP) - 1; Push (X) SP (SP) - 1; Push (A) SP (SP) - 1; Push (CCR) SP (SP) - 1; I 1 PCH Interrupt Vector High Byte PCL Interrupt Vector Low Byte CCR (A) X (A) A (CCR) VH I NZC SWI Software Interrupt - - 1 - - - INH 83 TAP Transfer A to CCR Transfer A to X Transfer CCR to A INH - - - - - - INH - - - - - - INH DIR INH INH - IX1 IX SP1 84 97 85 3D dd 4D 5D 6D ff 7D 9E6D ff 95 9F 94 Freescale Semiconductor, Inc... TAX TPA TST opr TSTA TSTX TST opr,X TST ,X TST opr,SP TSX TXA TXS A C CCR dd dd rr DD DIR DIX+ ee ff EXT ff H H hh ll I ii IMD IMM INH IX IX+ IX+D IX1 IX1+ IX2 M N Test for Negative or Zero (A) - $00 or (X) - $00 or (M) - $00 0-- Transfer SP to H:X Transfer X to A Transfer H:X to SP H:X (SP) + 1 A (X) (SP) (H:X) - 1 n opr PC PCH PCL REL rel rr SP1 SP2 SP U V X Z & | - - - - - - INH - - - - - - INH - - - - - - INH Accumulator Carry/borrow bit Condition code register Direct address of operand Direct address of operand and relative offset of branch instruction Direct to direct addressing mode Direct addressing mode Direct to indexed with post increment addressing mode High and low bytes of offset in indexed, 16-bit offset addressing Extended addressing mode Offset byte in indexed, 8-bit offset addressing Half-carry bit Index register high byte High and low bytes of operand address in extended addressing Interrupt mask Immediate operand byte Immediate source to direct destination addressing mode Immediate addressing mode Inherent addressing mode Indexed, no offset addressing mode Indexed, no offset, post increment addressing mode Indexed with post increment to direct addressing mode Indexed, 8-bit offset addressing mode Indexed, 8-bit offset, post increment addressing mode Indexed, 16-bit offset addressing mode Memory location Negative bit () -( ) # ? : -- Any bit Operand (one or two bytes) Program counter Program counter high byte Program counter low byte Relative addressing mode Relative program counter offset byte Relative program counter offset byte Stack pointer, 8-bit offset addressing mode Stack pointer 16-bit offset addressing mode Stack pointer Undefined Overflow bit Index register low byte Zero bit Logical AND Logical OR Logical EXCLUSIVE OR Contents of Negation (two's complement) Immediate value Sign extend Loaded with If Concatenated with Set or cleared Not affected 7.8 Opcode Map See Table 7-2. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Central Processor Unit (CPU) Data Sheet 87 For More Information On This Product, Go to: www.freescale.com Cycles 9 2 1 1 3 1 1 3 2 4 2 1 2 Effect on CCR Operand Freescale Semiconductor, Inc... Table 7-2. Opcode Map DIR 3 4 5 6 9E6 7 8 9 A B C D 9ED E 9EE F INH Read-Modify-Write INH IX1 SP1 IX IMM DIR EXT IX1 SP1 IX Control INH INH Register/Memory IX2 SP2 Central Processor Unit (CPU) 88 2 2 SUB 2 IMM 2 CMP 2 IMM 2 SBC 2 IMM 2 CPX 2 IMM 2 AND 2 IMM 2 BIT 2 IMM 2 LDA 2 IMM 2 AIS 2 IMM 2 EOR 2 IMM 2 ADC 2 IMM 2 ORA 2 IMM 2 ADD 2 IMM 5 SUB 4 SP2 5 CMP 4 SP2 5 SBC 4 SP2 5 CPX 4 SP2 5 AND 4 SP2 5 BIT 4 SP2 5 LDA 4 SP2 5 STA 4 SP2 5 EOR 4 SP2 5 ADC 4 SP2 5 ORA 4 SP2 5 ADD 4 SP2 4 SUB 3 SP1 4 CMP 3 SP1 4 SBC 3 SP1 4 CPX 3 SP1 4 AND 3 SP1 4 BIT 3 SP1 4 LDA 3 SP1 4 STA 3 SP1 4 EOR 3 SP1 4 ADC 3 SP1 4 ORA 3 SP1 4 ADD 3 SP1 4 1 NEG NEGA 2 DIR 1 INH 5 4 CBEQ CBEQA 3 DIR 3 IMM 5 MUL 1 INH 4 1 COM COMA 2 DIR 1 INH 4 1 LSR LSRA 2 DIR 1 INH 4 3 STHX LDHX 2 DIR 3 IMM 4 1 ROR RORA 2 DIR 1 INH 4 1 ASR ASRA 2 DIR 1 INH 4 1 LSL LSLA 2 DIR 1 INH 4 1 ROL ROLA 2 DIR 1 INH 4 1 DEC DECA 2 DIR 1 INH 5 3 DBNZ DBNZA 3 DIR 2 INH 4 1 INC INCA 2 DIR 1 INH 3 1 TST TSTA 2 DIR 1 INH 5 MOV 3 DD 3 1 CLR CLRA 2 DIR 1 INH MSB LSB Data Sheet Bit Manipulation DIR DIR Branch REL MSB LSB 0 1 0 1 2 3 4 5 6 7 8 Central Processor Unit (CPU) 0 Low Byte of Opcode in Hexadecimal 0 SP1 Stack Pointer, 8-Bit Offset SP2 Stack Pointer, 16-Bit Offset IX+ Indexed, No Offset with Post Increment IX1+ Indexed, 1-Byte Offset with Post Increment 9 A B Freescale Semiconductor, Inc. For More Information On This Product, Go to: www.freescale.com C D E F 5 BRSET0 3 DIR 5 BRCLR0 3 DIR 5 BRSET1 3 DIR 5 BRCLR1 3 DIR 5 BRSET2 3 DIR 5 BRCLR2 3 DIR 5 BRSET3 3 DIR 5 BRCLR3 3 DIR 5 BRSET4 3 DIR 5 BRCLR4 3 DIR 5 BRSET5 3 DIR 5 BRCLR5 3 DIR 5 BRSET6 3 DIR 5 BRCLR6 3 DIR 5 BRSET7 3 DIR 5 BRCLR7 3 DIR 4 BSET0 2 DIR 4 BCLR0 2 DIR 4 BSET1 2 DIR 4 BCLR1 2 DIR 4 BSET2 2 DIR 4 BCLR2 2 DIR 4 BSET3 2 DIR 4 BCLR3 2 DIR 4 BSET4 2 DIR 4 BCLR4 2 DIR 4 BSET5 2 DIR 4 BCLR5 2 DIR 4 BSET6 2 DIR 4 BCLR6 2 DIR 4 BSET7 2 DIR 4 BCLR7 2 DIR 3 BRA 2 REL 3 BRN 2 REL 3 BHI 2 REL 3 BLS 2 REL 3 BCC 2 REL 3 BCS 2 REL 3 BNE 2 REL 3 BEQ 2 REL 3 BHCC 2 REL 3 BHCS 2 REL 3 BPL 2 REL 3 BMI 2 REL 3 BMC 2 REL 3 BMS 2 REL 3 BIL 2 REL 3 BIH 2 REL 1 NEGX 1 INH 4 CBEQX 3 IMM 7 DIV 1 INH 1 COMX 1 INH 1 LSRX 1 INH 4 LDHX 2 DIR 1 RORX 1 INH 1 ASRX 1 INH 1 LSLX 1 INH 1 ROLX 1 INH 1 DECX 1 INH 3 DBNZX 2 INH 1 INCX 1 INH 1 TSTX 1 INH 4 MOV 2 DIX+ 1 CLRX 1 INH 4 NEG 2 IX1 5 CBEQ 3 IX1+ 3 NSA 1 INH 4 COM 2 IX1 4 LSR 2 IX1 3 CPHX 3 IMM 4 ROR 2 IX1 4 ASR 2 IX1 4 LSL 2 IX1 4 ROL 2 IX1 4 DEC 2 IX1 5 DBNZ 3 IX1 4 INC 2 IX1 3 TST 2 IX1 4 MOV 3 IMD 3 CLR 2 IX1 5 3 NEG NEG 3 SP1 1 IX 6 4 CBEQ CBEQ 4 SP1 2 IX+ 2 DAA 1 INH 5 3 COM COM 3 SP1 1 IX 5 3 LSR LSR 3 SP1 1 IX 4 CPHX 2 DIR 5 3 ROR ROR 3 SP1 1 IX 5 3 ASR ASR 3 SP1 1 IX 5 3 LSL LSL 3 SP1 1 IX 5 3 ROL ROL 3 SP1 1 IX 5 3 DEC DEC 3 SP1 1 IX 6 4 DBNZ DBNZ 4 SP1 2 IX 5 3 INC INC 3 SP1 1 IX 4 2 TST TST 3 SP1 1 IX 4 MOV 2 IX+D 4 2 CLR CLR 3 SP1 1 IX 7 3 RTI BGE 1 INH 2 REL 4 3 RTS BLT 1 INH 2 REL 3 BGT 2 REL 9 3 SWI BLE 1 INH 2 REL 2 2 TAP TXS 1 INH 1 INH 1 2 TPA TSX 1 INH 1 INH 2 PULA 1 INH 2 1 PSHA TAX 1 INH 1 INH 2 1 PULX CLC 1 INH 1 INH 2 1 PSHX SEC 1 INH 1 INH 2 2 PULH CLI 1 INH 1 INH 2 2 PSHH SEI 1 INH 1 INH 1 1 CLRH RSP 1 INH 1 INH 1 NOP 1 INH 1 STOP * 1 INH 1 1 WAIT TXA 1 INH 1 INH 3 SUB 2 DIR 3 CMP 2 DIR 3 SBC 2 DIR 3 CPX 2 DIR 3 AND 2 DIR 3 BIT 2 DIR 3 LDA 2 DIR 3 STA 2 DIR 3 EOR 2 DIR 3 ADC 2 DIR 3 ORA 2 DIR 3 ADD 2 DIR 2 JMP 2 DIR 4 4 BSR JSR 2 REL 2 DIR 2 3 LDX LDX 2 IMM 2 DIR 2 3 AIX STX 2 IMM 2 DIR 4 SUB 3 EXT 4 CMP 3 EXT 4 SBC 3 EXT 4 CPX 3 EXT 4 AND 3 EXT 4 BIT 3 EXT 4 LDA 3 EXT 4 STA 3 EXT 4 EOR 3 EXT 4 ADC 3 EXT 4 ORA 3 EXT 4 ADD 3 EXT 3 JMP 3 EXT 5 JSR 3 EXT 4 LDX 3 EXT 4 STX 3 EXT 4 SUB 3 IX2 4 CMP 3 IX2 4 SBC 3 IX2 4 CPX 3 IX2 4 AND 3 IX2 4 BIT 3 IX2 4 LDA 3 IX2 4 STA 3 IX2 4 EOR 3 IX2 4 ADC 3 IX2 4 ORA 3 IX2 4 ADD 3 IX2 4 JMP 3 IX2 6 JSR 3 IX2 4 LDX 3 IX2 4 STX 3 IX2 3 SUB 2 IX1 3 CMP 2 IX1 3 SBC 2 IX1 3 CPX 2 IX1 3 AND 2 IX1 3 BIT 2 IX1 3 LDA 2 IX1 3 STA 2 IX1 3 EOR 2 IX1 3 ADC 2 IX1 3 ORA 2 IX1 3 ADD 2 IX1 3 JMP 2 IX1 5 JSR 2 IX1 5 3 LDX LDX 4 SP2 2 IX1 5 3 STX STX 4 SP2 2 IX1 2 SUB 1 IX 2 CMP 1 IX 2 SBC 1 IX 2 CPX 1 IX 2 AND 1 IX 2 BIT 1 IX 2 LDA 1 IX 2 STA 1 IX 2 EOR 1 IX 2 ADC 1 IX 2 ORA 1 IX 2 ADD 1 IX 2 JMP 1 IX 4 JSR 1 IX 4 2 LDX LDX 3 SP1 1 IX 4 2 STX STX 3 SP1 1 IX MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Inherent REL Relative Immediate IX Indexed, No Offset Direct IX1 Indexed, 8-Bit Offset Extended IX2 Indexed, 16-Bit Offset Direct-Direct IMD Immediate-Direct Indexed-Direct DIX+ Direct-Indexed *Pre-byte for stack pointer indexed instructions INH IMM DIR EXT DD IX+D High Byte of Opcode in Hexadecimal 5 Cycles BRSET0 Opcode Mnemonic 3 DIR Number of Bytes / Addressing Mode MOTOROLA Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 8. Internal Clock Generator (ICG) Module 8.1 Introduction The internal clock generator (ICG) module is used to create a stable clock source for the microcontroller without using any external components. The ICG generates the oscillator output clock (CGMXCLK), which is used by the computer operating properly (COP), low-voltage inhibit (LVI), and other modules. The ICG also generates the clock generator output (CGMOUT), which is fed to the system integration module (SIM) to create the bus clocks. The bus frequency will be one-fourth the frequency of CGMXCLK and one-half the frequency of CGMOUT. Finally, the ICG generates the timebase clock (TBMCLK), which is used in the timebase module (TBM). Freescale Semiconductor, Inc... 8.2 Features The ICG has these features: * * * * Selectable external clock generator, either 1-pin external source or 2-pin crystal, multiplexed with port pins Internal clock generator with programmable frequency output in integer multiples of a nominal frequency (307.2 kHz 25 percent) Internal oscillator trimmed accuracy of 3.5 percent Bus clock software selectable from either internal or external clock (bus frequency range from 76.8 kHz 25 percent to 9.75 MHz 25 percent in 76.8-kHz increments) NOTE: For the MC68HC908EY16, do not exceed the maximum bus frequency of 8 MHz at 5.0 V. * * Timebase clock automatically selected from external clock if external clock is available Clock monitor for both internal and external clocks 8.3 Functional Description The ICG, shown in Figure 8-2, contains these major submodules: * * * * * Clock enable circuit Internal clock generator External clock generator Clock monitor circuit Clock selection circuit Data Sheet 89 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module INTERNAL BUS M68HC08 CPU CPU REGISTERS ARITHMETIC/LOGIC UNIT (ALU) SINGLE BREAKPOINT BREAK MODULE PORT A DDRA 5-BIT KEYBOARD INTERRUPT MODULE PTA6/SS PTA5/SPSCK PTA4/KBD4 PTA3/KBD3 PTA2/KBD2 PTA1/KBD1 2-CHANNEL TIMER INTERFACE MODULE A PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PORT B DDRB PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK PTC1/MOSI PTC0/MISO PTD1/TACH1 PTD0/TACH0 PTE1/RxD PTE0/TxD PORT C PORT E PORT D CONTROL AND STATUS REGISTERS 64 BYTES USER FLASH 15,872 BYTES USER RAM 512 BYTES Freescale Semiconductor, Inc... MONITOR ROM 310 BYTES FLASH PROGRAMMING (BURN-IN) ROM 1024 BYTES USER FLASH VECTOR SPACE 36 BYTES 2-CHANNEL TIMER INTERFACE MODULE B ENHANCED SERIAL COMMUNICATION INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE OSC2 OSC1 INTERNAL CLOCK GENERATOR MODULE SERIAL PERIPHERAL INTERFACE MODULE RST 24 INTERNAL SYSTEM INTEGRATION MODULE SINGLE EXTERNAL IRQ MODULE CONFIGURATION REGISTER MODULE PERIODIC WAKEUP TIMEBASE MODULE ARBITER MODULE PRESCALER MODULE IRQ VREFH VDDA VREFL VSSA VDD VSS DDRE DDRD DDRC 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE SECURITY MODULE POWER BEMF MODULE Figure 8-1. Block Diagram Highlighting ICG Block and Pins Data Sheet 90 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Functional Description CS RESET CLOCK SELECTION CIRCUIT CGMOUT CGMXCLK TBMCLK IOFF EOFF CMON ECGS CLOCK MONITOR CIRCUIT ICGS Freescale Semiconductor, Inc... FICGS DDIV[3:0] N[6:0} TRIM[7:0] INTERNAL CLOCK GENERATOR DSTG[7:0] ICLK IBASE ICGEN SIMOSCEN OSCENINSTOP EXTCLKEN ECGON ICGON ECGEN EXTXTALEN EXTSLOW EXTERNAL CLOCK GENERATOR ECLK CLOCK/PIN ENABLE CIRCUIT INTERNAL TO MCU EXTERNAL NAME NAME PTC4 LOGIC OSC1 PTC4 OSC2 PTC3 PTC3 LOGIC CONFIGURATION REGISTER BIT TOP LEVEL SIGNAL NAME NAME REGISTER BIT MODULE SIGNAL Figure 8-2. ICG Module Block Diagram MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 91 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module 8.3.1 Clock Enable Circuit The clock enable circuit is used to enable the internal clock (ICLK) or external clock (ECLK) and the port logic which is shared with the oscillator pins (OSC1 and OSC2). The clock enable circuit generates an ICG stop (ICGSTOP) signal which stops all clocks (ICLK, ECLK, and the low-frequency base clock, IBASE). ICGSTOP is set and the ICG is disabled in stop mode if the oscillator enable stop bit (OSCENINSTOP) in the configuration (CONFIG) register is clear. The ICG clocks will be enabled in stop mode if OSCENINSTOP is high. The internal clock enable signal (ICGEN) turns on the internal clock generator which generates ICLK. ICGEN is set (active) whenever the ICGON bit is set and the ICGSTOP signal is clear. When ICGEN is clear, ICLK and IBASE are both low. The external clock enable signal (ECGEN) turns on the external clock generator which generates ECLK. ECGEN is set (active) whenever the ECGON bit is set and the ICGSTOP signal is clear. ECGON cannot be set unless the external clock enable (EXTCLKEN) bit in the CONFIG is set. when ECGEN is clear, ECLK is low. The port C4 enable signal (PC4EN) turns on the port C4 logic. Since port C4 is on the same pin as OSC1, this signal is only active (set) when the external clock function is not desired. Therefore, PC4EN is clear when ECGON is set. PC4EN is not gated with ICGSTOP, which means that if the ECGON bit is set, the port C4 logic will remain disabled in stop mode. The port C3 enable signal (PC3EN) turns on the port C3 logic. Since port C3 is on the same pin as OSC2, this signal is only active (set) when 2-pin oscillator function is not desired. Therefore, PC3EN is clear when ECGON and the external crystal enable (EXTXTALEN) bit in the CONFIG are both set. PC4EN is not gated with ICGSTOP, which means that if ECGON and EXTXTALEN are set, the port C3 logic will remain disabled in stop mode. 8.3.2 Internal Clock Generator The internal clock generator, shown in Figure 8-3, creates a low frequency base clock (IBASE), which operates at a nominal frequency (fNOM) of 307.2 kHz 25 percent, and an internal clock (ICLK) which is an integer multiple of IBASE. This multiple is the ICG multiplier factor (N), which is programmed in the ICG multiplier register (ICGMR). The internal clock generator is turned off and the output clocks (IBASE and ICLK) are held low when the internal clock generator enable signal (ICGEN) is clear. The internal clock generator contains: * * * * Data Sheet 92 Freescale Semiconductor, Inc... A digitally controlled oscillator A modulo N divider A frequency comparator, which contains voltage and current references, a frequency to voltage converter, and comparators A digital loop filter MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Functional Description ICGEN VOLTAGE AND CURRENT REFERENCES ++ + DIGITAL LOOP FILTER FICGS DSTG[7:0] DDIV[3:0] DIGITALLY CONTROLLED OSCILLATOR - -- ICLK Freescale Semiconductor, Inc... TRIM[7:0] N[6:0] FREQUENCY COMPARATOR CLOCK GENERATOR MODULO N DIVIDER IBASE NAME NAME CONFIGURATION REGISTER BIT TOP LEVEL SIGNAL NAME NAME REGISTER BIT MODULE SIGNAL Figure 8-3. Internal Clock Generator Block Diagram 8.3.2.1 Digitally Controlled Oscillator The digitally controlled oscillator (DCO) is an inaccurate oscillator which generates the internal clock (ICLK). The clock period of ICLK is dependent on the digital loop filter outputs (DSTG[7:0] and DDIV[3:0]). Because of only a limited number of bits in DDIV and DSTG, the precision of the output (ICLK) is restricted to a precision of approximately 0.202 percent to 0.368 percent when measured over several cycles (of the desired frequency). Additionally, since the propagation delays of the devices used in the DCO ring oscillator are a measurable fraction of the bus clock period, reaching the long-term precision may require alternately running faster and slower than desired, making the worst case cycle-to-cycle frequency variation 6.45 percent to 11.8 percent (of the desired frequency). The valid values of DDIV:DSTG range from $000 to $9FF. For more information on the quantization error in the DCO, see 8.4.4 Quantization Error in DCO Output. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 93 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module 8.3.2.2 Modulo N Divider The modulo N divider creates the low-frequency base clock (IBASE) by dividing the internal clock (ICLK) by the ICG multiplier factor (N), contained in the ICG multiplier register (ICGMR). When N is programmed to a $01 or $00, the divider is disabled and ICLK is passed through to IBASE undivided. When the internal clock generator is stable, the frequency of IBASE will be equal to the nominal frequency (fNOM) of 307.2 kHz 25 percent. 8.3.2.3 Frequency Comparator Freescale Semiconductor, Inc... The frequency comparator effectively compares the low-frequency base clock (IBASE) to a nominal frequency, fNOM. First, the frequency comparator converts IBASE to a voltage by charging a known capacitor with a current reference for a period dependent on IBASE. This voltage is compared to a voltage reference with comparators, whose outputs are fed to the digital loop filter. The dependence of these outputs on the capacitor size, current reference, and voltage reference causes up to 25 percent error in fNOM. 8.3.2.4 Digital Loop Filter The digital loop filter (DLF) uses the outputs of the frequency comparator to adjust the internal clock (ICLK) clock period. The DLF generates the DCO divider control bits (DDIV[3:0]) and the DCO stage control bits (DSTG[7:0]), which are fed to the DCO. The DLF first concatenates the DDIV and DSTG registers (DDIV[3:0]:DSTG[7:0]) and then adds or subtracts a value dependent on the relative error in the low-frequency base clock's period, as shown in Table 8-1. In some extreme error conditions, such as operating at a VDD level which is out of specification, the DLF may attempt to use a value above the maximum ($9FF) or below the minimum ($000). In both cases, the value for DDIV will be between $A and $F. In this range, the DDIV value will be interpreted the same as $9 (the slowest condition). Recovering from this condition requires subtracting (increasing frequency) in the normal fashion until the value is again below $9FF. (If the desired value is $9xx, the value may settle at $Axx through $Fxx. This is an acceptable operating condition.) If the error is less than 5 percent, the internal clock generator's filter stable indicator (FICGS) is set, indicating relative frequency accuracy to the clock monitor. Data Sheet 94 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Functional Description Table 8-1. Correction Sizes from DLF to DCO Frequency Error of IBASE Compared to fNOM IBASE < 0.85 fNOM 0.85 fNOM < IBASE IBASE < 0.95 fNOM 0.95 fNOM < IBASE IBASE < fNOM fNOM < IBASE IBASE < 1.05 fNOM 1.05 fNOM < IBASE IBASE < 1.15 fNOM 1.15 fNOM < IBASE DDVI[3:0]:DSTG[7:0] Correction Current to New DDIV[3:0]:DSTG[7:0](1) Minimum -32 (-$020) Maximum Minimum -8 (-$008) Maximum Minimum -1 (-$001) Maximum Minimum +1 (+$001) Maximum Minimum +8 (+$008) Maximum Minimum +32 (+$020) Maximum $x00 to $x20 +2/17 +11.8% $x00 to $x08 $xDF to $xFF +0.5/17 +2/29 +2.94% +6.90% $x00 to $x01 $xF7 to $xFF +0.0625/17 +0.5/30.5 +0.368% +1.64% $x01 to $x00 $xFE to $xFF -0.0625/17.0625 +0.0625/30.9375 -0.366% +0.202% $x08 to $x00 $xFF to $xFE -0.5/17.5 -0.0625/31 -2.86% -0.202% $x20 to $x00 $xFF to $xF7 -2/19 -0.5/31 -10.5% -1.61% $xFF to $xDF Relative Correction in DCO -2/31 -6.45% Freescale Semiconductor, Inc... 1. x = Maximum error is independent of value in DDIV[3:0]. DDIV increments or decrements when an addition to DSTG[7:0] carries or borrows. 8.3.3 External Clock Generator The ICG also provides for an external oscillator or external clock source, if desired. The external clock generator, shown in Figure 8-4, contains an external oscillator amplifier and an external clock input path. 8.3.3.1 External Oscillator Amplifier The external oscillator amplifier provides the gain required by an external crystal connected in a Pierce oscillator configuration. The amount of this gain is controlled by the slow external (EXTSLOW) bit in the CONFIG. When EXTSLOW is set, the amplifier gain is reduced for operating low-frequency crystals (32 kHz to 100 kHz). When EXTSLOW is clear, the amplifier gain will be sufficient for 1-MHz to 8-MHz crystals. EXTSLOW must be configured correctly for the given crystal or the circuit may not operate. The amplifier is enabled when the external clock generator enable (ECGEN) signal is set and when the external crystal enable (EXTXTALEN) bit in the CONFIG is set. ECGEN is controlled by the clock enable circuit (see 8.3.1 Clock Enable Circuit) and indicates that the external clock function is desired. When enabled, the amplifier will be connected between the PTC4/OSC1 and PTC3/OSC2 pins. Otherwise, the PTC3/OSC2 pin reverts to its port function. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 95 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module ECGEN INPUT PATH EXTXTALEN EXTERNAL CLOCK GENERATOR EXTSLOW OSC1 PTC4 RB OSC2 PTC3 AMPLIFIER ECLK INTERNAL TO MCU Freescale Semiconductor, Inc... EXTERNAL NAME NAME NAME NAME CONFIGURATION BIT TOP LEVEL SIGNAL REGISTER BIT MODULE SIGNAL C1 X1 R S* *RS can be 0 (shorted) when used with higherfrequency crystals. Refer to manufacturer's data. C2 These components are required for external crystal use only. Figure 8-4. External Clock Generator Block Diagram In its typical configuration, the external oscillator requires five external components: 1. Crystal, X1 2. Fixed capacitor, C1 3. Tuning capacitor, C2 (can also be a fixed capacitor) 4. Feedback resistor, RB 5. Series resistor, RS (included in Figure 8-4 to follow strict Pierce oscillator guidelines and may not be required for all ranges of operation, especially with high frequency crystals. Refer to the crystal manufacturer's data for more information.) 8.3.3.2 External Clock Input Path The external clock input path is the means by which the microcontroller uses an external clock source. The input to the path is the PTC4/OSC1 pin and the output is the external clock (ECLK). The path, which contains input buffering, is enabled when the external clock generator enable signal (ECGEN) is set. When not enabled, the PTC4/OSC1 pin reverts to its port function. Data Sheet 96 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Functional Description 8.3.4 Clock Monitor Circuit The ICG contains a clock monitor circuit which, when enabled, will continuously monitor both the external clock (ECLK) and the internal clock (ICLK) to determine if either clock source has been corrupted. The clock monitor circuit, shown in Figure 8-5, contains these blocks: * * * Clock monitor reference generator Internal clock activity detector External clock activity detector CMON FICGS IBASE ICGEN EREF ICLK ACTIVITY DETECTOR IOFF IOFF Freescale Semiconductor, Inc... CMON FICGS IBASE ICGEN ICGS ICGS IBASE ICGON EXTXTALEN EXTSLOW EXTXTALEN EXTSLOW ECGS ECLK ECGEN EREF REFERENCE GENERATOR ESTBCLK IREF ESTBCLK IREF ECGEN ECLK ECGEN ECLK CMON ECLK ACTIVITY DETECTOR ECGS ECGS EOFF EOFF NAME NAME CONFIGURATION REGISTER BIT TOP LEVEL SIGNAL NAME NAME REGISTER BIT MODULE SIGNAL Figure 8-5. Clock Monitor Block Diagram MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 97 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module 8.3.4.1 Clock Monitor Reference Generator The clock monitor uses a reference based on one clock source to monitor the other clock source. The clock monitor reference generator generates the external reference clock (EREF) based on the external clock (ECLK) and the internal reference clock (IREF) based on the internal clock (ICLK). To simplify the circuit, the low-frequency base clock (IBASE) is used in place of ICLK because it always operates at or near 307.2 kHz. For proper operation, EREF must be at least twice as slow as IBASE and IREF must be at least twice as slow as ECLK. To guarantee that IREF is slower than ECLK and EREF is slower than IBASE, one of the signals is divided down. Which signal is divided and by how much is determined by the external slow (EXTSLOW) and external crystal enable (EXTXTALEN) bits in the CONFIG, according to the rules in Table 8-2. NOTE: Each signal (IBASE and ECLK) is always divided by four. A longer divider is used on either IBASE or ECLK based on the EXTSLOW bit. To conserve size, the long divider (divide by 4096) is also used as an external crystal stabilization divider. The divider is reset when the external clock generator is turned off or in stop mode (ECGEN is clear). When the external clock generator is first turned on, the external clock generator stable bit (ECGS) will be clear. This condition automatically selects ECLK as the input to the long divider. The external stabilization clock (ESTBCLK) will be ECLK divided by 16 when EXTXTALEN is low or 4096 when EXTXTALEN is high. This timeout allows the crystal to stabilize. The falling edge of ESTBCLK is used to set ECGS, which will set after a full 16 or 4096 cycles. When ECGS is set, the divider returns to its normal function. ESTBCLK may be generated by either IBASE or ECLK, but any clocking will only reinforce the set condition. If ECGS is cleared because the clock monitor determined that ECLK was inactive, the divider will revert to a stabilization divider. Since this will change the EREF and IREF divide ratios, it is important to turn the clock monitor off (CMON = 0) after inactivity is detected to ensure valid recovery. Freescale Semiconductor, Inc... Data Sheet 98 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Functional Description 8.3.4.2 Internal Clock Activity Detector The internal clock activity detector, shown in Figure 8-6, looks for at least one falling edge on the low-frequency base clock (IBASE) every time the external reference (EREF) is low. Since EREF is less than half the frequency of IBASE, this should occur every time. If it does not occur two consecutive times, the internal clock inactivity indicator (IOFF) is set. IOFF will be cleared the next time there is a falling edge of IBASE while EREF is low. The internal clock stable bit (ICGS) is also generated in the internal clock activity detector. ICGS is set when the internal clock generator's filter stable signal (FICGS) indicates that IBASE is within about 5 percent of the target 307.2 kHz 25 percent for two consecutive measurements. ICGS is cleared when FICGS is clear, the internal clock generator is turned off or is in stop mode (ICGEN is clear), or when IOFF is set. CMON EREF CK 1/4 R R D DFFRS IBASE CK S DLF MEASURE OUTPUT CLOCK ICGEN FICGS Q D CK R R Q D CK R DFFRR R Q ICGS DFFRR Q IOFF Freescale Semiconductor, Inc... NAME NAME CONFIGURATION REGISTER BIT TOP LEVEL SIGNAL NAME NAME REGISTER BIT MODULE SIGNAL Figure 8-6. Internal Clock Activity Detector MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 99 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module 8.3.4.3 External Clock Activity Detector The external clock activity detector, shown in Figure 8-7, looks for at least one falling edge on the external clock (ECLK) every time the internal reference (IREF) is low. Since IREF is less than half the frequency of ECLK, this should occur every time. If it does not occur two consecutive times, the external clock inactivity indicator (EOFF) is set. EOFF will be cleared the next time there is a falling edge of ECLK while IREF is low. The external clock stable bit (ECGS) is also generated in the external clock activity detector. ECGS is set on a falling edge of the external stabilization clock (ESTBCLK). This will be 4096 ECLK cycles after the external clock generator on bit is set, or the MCU exits stop mode (ECGEN = 1) if the external crystal enable (EXTXTALEN) in the CONFIG is set, or 16 cycles when EXTXTALEN is clear. ECGS is cleared when the external clock generator is turned off or in stop mode (ECGEN is clear) or when EOFF is set. CMON IREF CK 1/4 R R D DFFRS ECLK CK S ESTBCLK ECGEN Q D DFFRR CK R Q EGGS R Q EOFF Freescale Semiconductor, Inc... NAME NAME CONFIGURATION REGISTER BIT TOP LEVEL SIGNAL NAME NAME REGISTER BIT MODULE SIGNAL Figure 8-7. External Clock Activity Detector Data Sheet 100 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Functional Description 8.3.5 Clock Selection Circuit The clock selection circuit, shown in Figure 8-8, contains two clock switches which generate the oscillator output clock (CGMXCLK) and the timebase clock (TBMCLK) from either the internal clock (ICLK) or the external clock (ECLK). The clock selection circuit also contains a divide-by-two circuit which creates the clock generator output clock (CGMOUT), which generates the bus clocks. CS ICLK SELECT ICLK ECLK IOFF EOFF FORCE_I FORCE_E OUTPUT TBMCLK SYNCHRONIZING CLOCK SWITCHER DIV2 OUTPUT CGMXCLK Freescale Semiconductor, Inc... ECLK IOFF EOFF RESET VSS ECGON CGMOUT SELECT ICLK ECLK IOFF EOFF FORCE_I FORCE_E SYNCHRONIZING CLOCK SWITCHER NAME NAME CONFIGURATION REGISTER BIT TOP LEVEL SIGNAL NAME NAME REGISTER BIT MODULE SIGNAL Figure 8-8. Clock Selection Circuit Block Diagram 8.3.5.1 Clock Selection Switches The first switch creates the oscillator output clock (CGMXCLK) from either the internal clock (ICLK) or the external clock (ECLK), based on the clock select bit (CS; set selects ECLK, clear selects ICLK). When switching the CS bit, both ICLK and ECLK must be on (ICGON and ECGON set). The clock being switched to also must be stable (ICGS or ECGS set). The second switch creates the timebase clock (TBMCLK) from ICLK or ECLK based on the external clock on bit. When ECGON is set, the switch automatically selects the external clock, regardless of the state of the ECGS bit. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 101 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module 8.3.5.2 Clock Switching Circuit To robustly switch between the internal clock (ICLK) and the external clock (ECLK), the switch assumes the clocks are completely asynchronous, so a synchronizing circuit is required to make the transition. When the select input (the clock select bit for the oscillator output clock switch or the external clock on bit for the timebase clock switch) is changed, the switch will continue to operate off the original clock for between one and two cycles as the select input is transitioned through one side of the synchronizer. Next, the output will be held low for between one and two cycles of the new clock as the select input transitions through the other side. Then the output starts switching at the new clock's frequency. This transition guarantees that no glitches will be seen on the output even though the select input may change asynchronously to the clocks. The unpredictably of the transition period is a necessary result of the asynchronicity. The switch automatically selects ICLK during reset. When the clock monitor is on (CMON is set) and it determines one of the clock sources is inactive (as indicated by the IOFF or EOFF signals), the circuit is forced to select the active clock. There are no clocks for the inactive side of the synchronizer to properly operate, so that side is forced deselected. However, the active side will not be selected until one to two clock cycles after the IOFF or EOFF signal transitions. Freescale Semiconductor, Inc... 8.4 Usage Notes The ICG has several features which can provide protection to the microcontroller if properly used. Other features can greatly simplify usage of the ICG if certain techniques are employed. This section describes several possible ways to use the ICG and its features. These techniques are not the only ways to use the ICG and may not be optimum for all environments. In any case, these techniques should be used only as a template, and the user should modify them according to the application's requirements. These notes include: * * * * * * * * Switching clock sources Enabling the clock monitor Using clock monitor interrupts Quantization error in digitally controlled oscillator (DCO) output Switching internal clock frequencies Nominal frequency settling time Improving frequency settling time Trimming frequency Data Sheet 102 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Usage Notes 8.4.1 Switching Clock Sources Switching from one clock source to another requires both clock sources to be enabled and stable. A simple flow requires: * * * * Enable desired clock source Wait for it to become stable Switch clocks Disable previous clock source Freescale Semiconductor, Inc... The key point to remember in this flow is that the clock source cannot be switched (CS cannot be written) unless the desired clock is on and stable. A short assembly code example of how to employ this flow is shown in Figure 8-9. This code is for illustrative purposes only and does not represent valid syntax for any particular assembler. ;Clock Switching Code Example ;This code switches from Internal to External clock ;Clock Monitor and interrupts are not enabled ;Mask for CS, ECGON, ECGS ; If switching from External to Internal, mask is $0C. ;Other code here, such as writing the COP, since ECGS may ; take some time to set ;Try to set CS, ECGON and clear ICGON. ICGON will not ; clear until CS is set, and CS will not set until ; ECGON and ECGS are set. ;Check to see if ECGS set, then CS set, then ICGON clear ;Keep looping until ICGON is clear. start loop lda ** sta #$13 ** icgcr cmpa bne icgcr loop Figure 8-9. Code Example for Switching Clock Sources 8.4.2 Enabling the Clock Monitor Many applications require the clock monitor to determine if one of the clock sources has become inactive, so the other can be used to recover from a potentially dangerous situation. Using the clock monitor requires both clocks to be active (ECGON and ICGON both set). To enable the clock monitor, both clocks also must be stable (ECGS and ICGS both set). This is to prevent the use of the clock monitor when a clock is first turned on and potentially unstable. Enabling the clock monitor and clock monitor interrupts requires a flow similar to this: * * * * * Enable the alternate clock source Wait for both clock sources to be stable Switch to the desired clock source if necessary Enable the clock monitor Enable clock monitor interrupts MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 103 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module These events must happen in sequence. A short assembly code example of how to employ this flow is shown in Figure 8-10. This code is for illustrative purposes only and does not represent valid syntax for any particular assembler. ;Clock Monitor Enabling Code Example ;This code turns on both clocks, selects the desired ; one, then turns on the Clock Monitor and Interrupts #$AF ;Mask for CMIE, CMON, ICGON, ICGS, ECGON, ECGS ; If Internal Clock desired, mask is $AF ; If External Clock desired, mask is $BF ; If interrupts not desired mask is $2F int; $3F ext ** ;Other code here, such as writing the COP, since ECGS ; and ICGS may take some time to set. icgcr ;Try to set CMIE. CMIE wont set until CMON set; CMON ; won't set until ICGON, ICGS, ECGON, ECGS set. 6,ICGCR,error ;Verify CMF is not set icgcr ;Check if ECGS set, then CMON set, then CMIE set loop ;Keep looping until CMIE is set. start lda loop ** sta brset cmpa bne Freescale Semiconductor, Inc... Figure 8-10. Code Example for Enabling the Clock Monitor 8.4.3 Using Clock Monitor Interrupts The clock monitor circuit can be used to recover from perilous situations such as crystal loss. To use the clock monitor effectively, these points should be observed: * * Enable the clock monitor and clock monitor interrupts. The first statement in the clock monitor interrupt service routine (CMISR) should be a read to the ICG control register (ICGCR) to verify that the clock monitor flag (CMF) is set. This is also the first step in clearing the CMF bit. The second statement in the CMISR should be a write to the ICGCR to clear the CMF bit (write the bit low). Writing the bit high will not affect it. This statement does not need to immediately follow the first, but must be contained in the CMISR. The third statement in the CMISR should be to clear the CMON bit. This is required to ensure proper reconfiguration of the reference dividers. This statement also must be contained in the CMISR. Although the clock monitor can be enabled only when both clocks are stable (ICGS is set or ECGS is set), it will remain set if one of the clocks goes unstable. The clock monitor only works if the external slow (EXTSLOW) bit in the CONFIG is set to the correct value. The internal and external clocks must both be enabled and running to use the clock monitor. * * * * * Data Sheet 104 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Usage Notes * When the clock monitor detects inactivity, the inactive clock is automatically deselected and the active clock selected as the source for CGMXCLK and TBMCLK. The CMISR can use the state of the CS bit to check which clock is inactive. When the clock monitor detects inactivity, the application may have been subjected to extreme conditions which may have affected other circuits. The CMISR should take any appropriate precautions. * 8.4.4 Quantization Error in DCO Output The digitally controlled oscillator (DCO) is comprised of three major sub-blocks: 1. Binary weighted divider 2. Variable-delay ring oscillator 3. Ring oscillator fine-adjust circuit Each of these blocks affects the clock period of the internal clock (ICLK). Since these blocks are controlled by the digital loop filter (DLF) outputs DDIV and DSTG, the output of the DCO can change only in quantized steps as the DLF increments or decrements its output. The following sections describe how each block will affect the output frequency. 8.4.4.1 Digitally Controlled Oscillator The digitally controlled oscillator (DCO) is an inaccurate oscillator which generates the internal clock (ICLK), whose clock period is dependent on the digital loop filter outputs (DSTG[7:0] and DDIV[3:0]). Because of the digital nature of the DCO, the clock period of ICLK will change in quantized steps. This will create a clock period difference or quantization error (Q-ERR) from one cycle to the next. Over several cycles or for longer periods, this error is divided out until it reaches a minimum error of 0.202 percent to 0.368 percent. The dependence of this error on the DDIV[3:0] value and the number of cycles the error is measured over is shown in Table 8-2. 8.4.4.2 Binary Weighted Divider The binary weighted divider divides the output of the ring oscillator by a power of two, specified by the DCO divider control bits (DDIV[3:0]). DDIV maximizes at %1001 (values of %1010 through %1111 are interpreted as %1001), which corresponds to a divide by 512. When DDIV is %0000, the ring oscillator's output is divided by 1. Incrementing DDIV by one will double the period; decrementing DDIV will halve the period. The DLF cannot directly increment or decrement DDIV; DDIV is only incremented or decremented when an addition or subtraction to DSTG carries or borrows. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 105 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Table 8-2. Quantization Error in ICLK DDIV[3:0] %0000 (min) %0000 (min) %0000 (min) %0001 %0001 %0001 ICLK Cycles 1 4 32 1 4 16 1 4 8 1 4 1 2 1 Bus Cycles NA 1 8 NA 1 4 NA 1 2 NA 1 NA 1 1 ICLK Q-ERR 6.45%-11.8% 1.61%-2.94% 0.202%-0.368% 3.23%-5.88% 0.806%-1.47% 0.202%-0.368% 1.61%-2.94% 0.403%-0.735% 0.202%-0.368% 0.806%-1.47% 0.202%-0.368% 0.403%-0.735% 0.202%-0.368% 0.202%-0.368% Freescale Semiconductor, Inc... %0010 %0010 %0010 %0011 %0011 %0100 %0100 %0101-%1001 (max) 8.4.4.3 Variable-Delay Ring Oscillator The variable-delay ring oscillator's period is adjustable from 17 to 31 stage delays, in increments of two, based on the upper three DCO stage control bits (DSTG[7:5]). A DSTG[7:5] of %000 corresponds to 17 stage delays; DSTG[7:5] of %111 corresponds to 31 stage delays. Adjusting the DSTG[5] bit has a 6.45 percent to 11.8 percent effect on the output frequency. This also corresponds to the size correction made when the frequency error is greater than 15 percent. The value of the binary weighted divider does not affect the relative change in output clock period for a given change in DSTG[7:5]. 8.4.4.4 Ring Oscillator Fine-Adjust Circuit The ring oscillator fine-adjust circuit causes the ring oscillator to effectively operate at non-integer numbers of stage delays by operating at two different points for a variable number of cycles specified by the lower five DCO stage control bits (DSTG[4:0]). For example: * * * * When DSTG[7:5] is %011, the ring oscillator nominally operates at 23 stage delays. When DSTG[4:0] is %00000, the ring will always operate at 23 stage delays. When DSTG[4:0] is %00001, the ring will operate at 25 stage delays for one of 32 cycles and at 23 stage delays for 31 of 32 cycles. Likewise, when DSTG[4:0] is %11111, the ring operates at 25 stage delays for 31 of 32 cycles and at 23 stage delays for one of 32 cycles. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA Data Sheet 106 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Usage Notes * When DSTG[7:5] is %111, similar results are achieved by including a variable divide-by-two, so the ring operates at 31 stages for some cycles and at 17 stage delays, with a divide-by-two for an effective 34 stage delays, for the remainder of the cycles. Adjusting the DSTG[0] bit has a 0.202 percent to 0.368 percent effect on the output clock period. This corresponds to the minimum size correction made by the DLF, and the inherent, long-term quantization error in the output frequency. 8.4.5 Switching Internal Clock Frequencies Freescale Semiconductor, Inc... The frequency of the internal clock (ICLK) may need to be changed for some applications. For example, if the reset condition does not provide the correct frequency, or if the clock is slowed down for a low-power mode (or sped up after a low-power mode), the frequency must be changed by programming the internal clock multiplier factor (N). The frequency of ICLK is N times the frequency of IBASE, which is 307.2 kHz 25 percent. Before switching frequencies by changing the N value, the clock monitor must be disabled. This is because when N is changed, the frequency of the low-frequency base clock (IBASE) will change proportionally until the digital loop filter has corrected the error. Since the clock monitor uses IBASE, it could erroneously detect an inactive clock. The clock monitor cannot be re-enabled until the internal clock is stable again (ICGS is set). The following flow is an example of how to change the clock frequency: * * * * * * Verify there is no clock monitor interrupt by reading the CMF bit. Turn off the clock monitor. If desired, switch to the external clock (see 8.4.1 Switching Clock Sources). Change the value of N. Switch back to internal (see 8.4.1 Switching Clock Sources), if desired. Turn on the clock monitor (see 8.4.2 Enabling the Clock Monitor), if desired. 8.4.6 Nominal Frequency Settling Time Because the clock period of the internal clock (ICLK) is dependent on the digital loop filter outputs (DDIV and DSTG) which cannot change instantaneously, ICLK temporarily will operate at an incorrect clock period when any operating condition changes. This happens whenever the part is reset, the ICG multiply factor (N) is changed, the ICG trim factor (TRIM) is changed, or the internal clock is enabled after inactivity (stop mode or disabled operation). The time that the ICLK takes to adjust to the correct period is known as the settling time. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 107 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Settling time depends primarily on how many corrections it takes to change the clock period and the period of each correction. Since the corrections require four periods of the low-frequency base clock (4*IBASE), and since ICLK is N (the ICG multiply factor for the desired frequency) times faster than IBASE, each correction takes 4*N*ICLK. The period of ICLK, however, will vary as the corrections occur. 8.4.6.1 Settling to Within 15 Percent When the error is greater than 15 percent, the filter takes eight corrections to double or halve the clock period. Due to how the DCO increases or decreases the clock period, the total period of these eight corrections is approximately 11 times the period of the fastest correction. (If the corrections were perfectly linear, the total period would be 11.5 times the minimum period; however, the ring must be slightly nonlinear.) Therefore, the total time it takes to double or halve the clock period is 44*N*ICLKFAST. If the clock period needs more than doubled or halved, the same relationship applies, only for each time the clock period needs doubled, the total number of cycles doubles. That is, when transitioning from fast to slow, going from the initial speed to half speed takes 44*N*ICLKFAST; from half speed to quarter speed takes 88*N*ICLKFAST; going from quarter speed to eighth speed takes 176*N*ICLKFAST; and so on. This series can be expressed as (2x-1)*44*N*ICLKFAST, where x is the number of times the speed needs doubled or halved. Since 2x happens to be equal to ICLKSLOW/ICLKFAST, the equation reduces to 44*N*(ICLKSLOW-ICLKFAST). Note that increasing speed takes much longer than decreasing speed since N is higher. This can be expressed in terms of the initial clock period (1) minus the final clock period (2) as such: 15 = abs [ 44N ( 1 - 2 ) ] 8.4.6.2 Settling to Within 5 Percent Once the clock period is within 15 percent of the desired clock period, the filter starts making smaller adjustments. When between 15 percent and 5 percent error, each correction will adjust the clock period between 1.61 percent and 2.94 percent. In this mode, a maximum of eight corrections will be required to get to less than 5 percent error. Since the clock period is relatively close to desired, each correction takes approximately the same period of time, or 4*IBASE. At this point, the internal clock stable bit (ICGS) will be set and the clock frequency is usable, although the error will be as high as 5 percent. The total time to this point is: 5 = abs [ 44N ( 1 - 2 ) ] + 32 IBASE 8.4.6.3 Total Settling Time Once the clock period is within 5 percent of the desired clock period, the filter starts making minimum adjustments. In this mode, each correction will adjust the frequency between 0.202 percent and 0.368 percent. A maximum of 24 corrections Data Sheet 108 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA Freescale Semiconductor, Inc... For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Usage Notes will be required to get to the minimum error. Each correction takes approximately the same period of time, or 4*IBASE. Added to the corrections for 15 percent to 5 percent, this makes 32 corrections (128*IBASE) to get from 15 percent to the minimum error. The total time to the minimum error is: tot = abs [ 44N ( 1 - 2 ) ] + 128 IBASE The equations for 15, 5, and tot are dependent on the actual initial and final clock periods 1 and 2, not the nominal. This means the variability in the ICLK frequency due to process, temperature, and voltage must be considered. Additionally, other process factors and noise can affect the actual tolerances of the points at which the filter changes modes. This means a worst case adjustment of up to 35 percent (ICLK clock period tolerance plus 10 percent) must be added. This adjustment can be reduced with trimming. Table 8-3 shows some typical values for settling time. Table 8-3. Typical Settling Time Examples 1 1/ (6.45 MHz) 1/ (25.8 MHz) 1/ (25.8 MHz) 1/ (307.2 kHz) 2 1/ (25.8 MHz) 1/ (6.45 MHz) 1/ (307.2 kHz) 1/ (25.8 MHz) N 84 21 1 84 15 430 s 107 s 141 s 11.9 ms 5 535 s 212 s 246 s 12.0 ms tot 850 s 525 s 560 s 12.3 ms Freescale Semiconductor, Inc... 8.4.7 Trimming Frequency on the Internal Clock Generator The unadjusted frequency of the low-frequency base clock (IBASE), when the comparators in the frequency comparator indicate zero error, will vary as much as 25 percent due to process, temperature, and voltage dependencies. These dependencies are in the voltage and current references, the offset of the comparators, and the internal capacitor. The method of changing the unadjusted operating point is by changing the size of the capacitor. This capacitor is designed with 639 equally sized units. Of that number, 384 of these units are always connected. The remaining 255 units are put in by adjusting the ICG trim factor (TRIM). The default value for TRIM is $80, or 128 units, making the default capacitor size 512. Each unit added or removed will adjust the output frequency by about 0.195 percent of the unadjusted frequency (adding to TRIM will decrease frequency). Therefore, the frequency of IBASE can be changed to 25 percent of its unadjusted value, which is enough to cancel the process variability mentioned before. The best way to trim the internal clock is to use the timer to measure the width of an input pulse on an input capture pin (this pulse must be supplied by the application and should be as long or wide as possible). Considering the prescale value of the timer and the theoretical (zero error) frequency of the bus (307.2 kHz *N/4), the error can be calculated. This error, expressed as a percentage, can be divided by 0.195 percent and the resultant factor added or subtracted from TRIM. This process should be repeated to eliminate any residual error. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 109 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module 8.5 Low-Power Modes The WAIT and STOP instructions put the MCU in low power- consumption standby modes. 8.5.1 Wait Mode The ICG remains active in wait mode. If enabled, the ICG interrupt to the CPU can bring the MCU out of wait mode. In some applications, low power-consumption is desired in wait mode and a high-frequency clock is not needed. In these applications, reduce power consumption by either selecting a low-frequency external clock and turn the internal clock generator off or reduce the bus frequency by minimizing the ICG multiplier factor (N) before executing the WAIT instruction. 8.5.2 Stop Mode The value of the oscillator enable in stop (OSCENINSTOP) bit in the CONFIG determines the behavior of the ICG in stop mode. If OSCENINSTOP is low, the ICG is disabled in stop and, upon execution of the STOP instruction, all ICG activity will cease and the output clocks (CGMXCLK, CGMOUT, and TBMCLK) will be held low. Power consumption will be minimal. If OSCENINSTOP is high, the ICG is enabled in stop and activity will continue. This is useful if the timebase module (TBM) is required to bring the MCU out of stop mode. ICG interrupts will not bring the MCU out of stop mode in this case. During stop mode, if OSCENINSTOP is low, several functions in the ICG are affected. The stable bits (ECGS and ICGS) are cleared, which will enable the external clock stabilization divider upon recovery. The clock monitor is disabled (CMON = 0) which will also clear the clock monitor interrupt enable (CMIE) and clock monitor flag (CMF) bits. The CS, ICGON, ECGON, N, TRIM, DDIV, and DSTG bits are unaffected. Freescale Semiconductor, Inc... 8.6 CONFIG Options Four CONFIG options affect the functionality of the ICG. These options are: 1. EXTCLKEN, external clock enable 2. EXTXTALEN, external crystal enable 3. EXTSLOW, slow external clock 4. OSCENINSTOP, oscillator enable in stop All CONFIG options will have a default setting. Refer to Section 5. Configuration Registers (CONFIG1 and CONFIG2) on how the CONFIG is used. Data Sheet 110 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module CONFIG Options 8.6.1 External Clock Enable (EXTCLKEN) External clock enable (EXTCLKEN), when set, enables the ECGON bit to be set. ECGON turns on the external clock input path through the PTC4/OSC1 pin. When EXTCLKEN is clear, ECGON cannot be set and PTC4/OSC1 will always perform the PTC4 function. The default state for this option is clear. 8.6.2 External Crystal Enable (EXTXTALEN) External crystal enable (EXTXTALEN), when set, will enable an amplifier to drive the PTC3/OSC2 pin from the PTC4/OSC1 pin. The amplifier will drive only if the external clock enable (EXTCLKEN) bit and the ECGON bit are also set. If EXTCLKEN or ECGON are clear, PTC3/OSC2 will perform the PTC3 function. When EXTXTALEN is clear, PTC3/OSC2 will always perform the PTC3 function. EXTXTALEN, when set, also configures the clock monitor to expect an external clock source in the valid range of crystals (30 kHz to 100 kHz or 1 MHz to 8 MHz). When EXTXTALEN is clear, the clock monitor will expect an external clock source in the valid range for externally generated clocks when using the clock monitor (60 Hz to 32 MHz). EXTXTALEN, when set, also configures the external clock stabilization divider in the clock monitor for a 4096 cycle timeout to allow the proper stabilization time for a crystal. When EXTXTALEN is clear, the stabilization divider is configured to 16 cycles since an external clock source does not need a startup time. The default state for this option is clear. 8.6.3 Slow External Clock (EXTSLOW) Slow external clock (EXTSLOW), when set, will decrease the drive strength of the oscillator amplifier, enabling low-frequency crystal operation (30 kHz-100 kHz) if properly enabled with the external clock enable (EXTCLKEN) and external crystal enable (EXTXTALEN) bits. When clear, EXTSLOW enables high-frequency crystal operation (1 MHz to 8 MHz). EXTSLOW, when set, also configures the clock monitor to expect an external clock source that is slower than the low-frequency base clock (60 Hz to 307.2 kHz). When EXTSLOW is clear, the clock monitor will expect an external clock faster than the low-frequency base clock (307.2 kHz to 32 MHz). The default state for this option is clear. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 111 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module 8.6.4 Oscillator Enable In Stop (OSCENINSTOP) Oscillator enable in stop (OSCENINSTOP), when set, will enable the ICG to continue to generate clocks (either CGMXCLK, CGMOUT, or TBMCLK) in stop mode. This function is used to keep the timebase running while the rest of the microcontroller stops. When OSCENINSTOP is clear, all clock generation will cease and CGMXCLK, CGMOUT, and TBMCLK will be forced low during stop mode. The default state for this option is clear. 8.7 Input/Output (I/O) Registers Freescale Semiconductor, Inc... The ICG contains five registers, summarized in Figure 8-11. These registers are: 1. ICG control register, ICGCR 2. ICG multiplier register, ICGMR 3. ICG trim register, ICGTR 4. ICG DCO divider control register, ICGDVR 5. ICG DCO stage control register, ICGDSR Addr. $0036 Register Name ICG Control Register Read: (ICGCR) Write: See page 114. Reset: Bit 7 CMIE 0 6 CMF 0(1) 0 5 CMON 0 4 CS 0 3 ICGON 1 2 ICGS 0 1 ECGON 0 Bit 0 ECGS 0 1. See 8.7.1 ICG Control Register for method of clearing the CMF bit. ICG Multiply Register Read: (ICGMR) Write: See page 116. Reset: ICG Trim Register Read: (ICGTR) Write: See page 116. Reset: ICG Divider Control Read: Register (ICGDVR) Write: See page 117. Reset: ICG DCO Stage Control Read: Register (ICGDSR) Write: See page 117. Reset: $0037 N6 0 TRIM7 1 0 TRIM6 0 N5 0 TRIM5 0 N4 1 TRIM4 0 N3 0 TRIM3 0 DDIV3 N2 1 TRIM2 0 DDIV2 U DSTG2 R N1 0 TRIM1 0 DDIV1 U DSTG1 R U = Unaffected N0 1 TRIM0 0 DDIV0 U DSTG0 R $0038 $0039 0 DSTG7 R 0 DSTG6 R = Unimplemented 0 DSTG5 R 0 DSTG4 R R U DSTG3 R = Reserved $003A Unaffected by reset Figure 8-11. ICG Module I/O Register Summary Data Sheet 112 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Input/Output (I/O) Registers Several of the bits in these registers have interaction where the state of one bit may force another bit to a particular state or prevent another bit from being set or cleared. A summary of this interaction is shown in Table 8-4. Table 8-4. ICG Module Register Bit Interaction Summary Register Bit Results for Given Condition Condition CMIE CMF CMON CS ICGON ICGS ECQON ECQ N[6:0] TRIM[7:0] DDIV[3:0] DSTQ[7:0] Reset 0 0 0 -- 0 -- -- -- 0 -- us 0 us -- -- (0) (0) 0 0 0 (1) 0 -- -- -- 0 -- -- 0 -- 1* 1* (0) (0) 0 0 0 1 (0) (1) -- -- 0 -- us 0 us (1) (1) (0) (0) 0 -- 0 -- -- -- (0) (1) 1 -- uc 0 us 1 0 -- -- 1 -- 1 1 -- 1 1 -- (0) (1) -- 1 -- (1) (1) -- -- 0 0 -- -- -- -- -- -- 0 -- (0) -- -- 0 -- 0* 0* 0 -- 0 1 -- 1 -- 1 1 -- -- (0) -- (1) (1) -- -- 0 0 0 -- -- -- -- -- -- -- -- 0 (0) -- 0 -- -- $15 -- -- uw -- uw -- -- -- -- -- -- -- uw uw -- -- $80 -- -- uw -- uw -- -- -- -- -- -- -- uw uw -- -- -- -- uw uw -- uw uw -- -- uw -- uw -- uw uw -- -- -- -- uw uw -- uw uw -- -- uw -- uw -- uw uw -- -- Freescale Semiconductor, Inc... OSCENINSTOP = 0, STOP = 1 EXTCLKEN = 0 CMF = 1 CMON = 0 CMON = 1 CS = 0 CS = 1 ICGON = 0 ICGON = 1 ICGS = 0 ECGON = 0 ECGS = 0 IOFF = 1 EOFF = 1 N = written TRIM = written -- 0, 1 0*, 1* (0), (1) us, uc, uw Register bit is unaffected by the given condition. Register bit is forced clear or set (respectively) in the given condition. Register bit is temporarily forced clear or set (respectively) in the given condition. Register bit must be clear or set (respectively) for the given condition to occur. Register bit cannot be set, cleared, or written (respectively) in the given condition. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 113 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module 8.7.1 ICG Control Register The ICG control register (ICGCR) contains the control and status bits for the internal clock generator, external clock generator, and clock monitor as well as the clock select and interrupt enable bits. Address: $0036 Bit 7 Read: Write: Reset: CMIE 0 6 CMF 0 (1) 5 CMON 0 4 CS 0 3 ICGON 1 2 ICGS 0 1 ECGON 0 Bit 0 ECGS 0 0 Freescale Semiconductor, Inc... 1. See CMF bit description for method of clearing CMF bit. = Unimplemented Figure 8-12. ICG Control Register (ICGCR) CMIE -- Clock Monitor Interrupt Enable Bit This read/write bit enables clock monitor interrupts. An interrupt will occur when both CMIE and CMF are set. CMIE can be set when the CMON bit has been set for at least one cycle. CMIE is forced clear when CMON is clear or during reset. 1 = Clock monitor interrupts enabled 0 = Clock monitor interrupts disabled CMF -- Clock Monitor Interrupt Flag This read-only bit is set when the clock monitor determines that either ICLK or ECLK becomes inactive and the CMON bit is set. This bit is cleared by first reading the bit while it is set, followed by writing the bit low. This bit is forced clear when CMON is clear or during reset. 1 = Either ICLK or ECLK has become inactive. 0 = ICLK and ECLK have not become inactive since the last read of the ICGCR, or the clock monitor is disabled. CMON -- Clock Monitor On Bit This read/write bit enables the clock monitor. CMON can be set when both ICLK and ECLK have been on and stable for at least one bus cycle. (ICGON, ECGON, ICGS, and ECGS are all set.) CMON is forced set when CMF is set, to avoid inadvertent clearing of CMF. CMON is forced clear when either ICGON or ECGON is clear, during stop mode with OSCENINSTOP low, or during reset. 1 = Clock monitor output enabled 0 = Clock monitor output disabled CS -- Clock Select Bit This read/write bit determines which clock will generate the oscillator output clock (CGMXCLK). This bit can be set when ECGON and ECGS have been set for at least one bus cycle and can be cleared when ICGON and ICGS have been set for at least one bus cycle. This bit is forced set when the clock monitor Data Sheet 114 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Input/Output (I/O) Registers determines the internal clock (ICLK) is inactive or when ICGON is clear. This bit is forced clear when the clock monitor determines that the external clock (ECLK) is inactive, when ECGON is clear, or during reset. 1 = External clock (ECLK) sources CGMXCLK 0 = Internal clock (ICLK) sources CGMXCLK ICGON -- Internal Clock Generator On Bit This read/write bit enables the internal clock generator. ICGON can be cleared when the CS bit has been set and the CMON bit has been clear for at least one bus cycle. ICGON is forced set when the CMON bit is set, the CS bit is clear, or during reset. 1 = Internal clock generator enabled 0 = Internal clock generator disabled ICGS -- Internal Clock Generator Stable Bit This read-only bit indicates when the internal clock generator has determined that the internal clock (ICLK) is within about 5 percent of the desired value. This bit is forced clear when the clock monitor determines the ICLK is inactive, when ICGON is clear, when the ICG multiplier register (ICGMR) is written, when the ICG TRIM register (ICGTR) is written, during stop mode with OSCENINSTOP low, or during reset. 1 = Internal clock is within 5 percent of the desired value. 0 = Internal clock may not be within 5 percent of the desired value. ECGON -- External Clock Generator On Bit This read/write bit enables the external clock generator. ECGON can be cleared when the CS and CMON bits have been clear for at least one bus cycle. ECGON is forced set when the CMON bit or the CS bit is set. ECGON is forced clear during reset. 1 = External clock generator enabled 0 = External clock generator disabled ECGS -- External Clock Generator Stable Bit This read-only bit indicates when at least 4096 external clock (ECLK) cycles have elapsed since the external clock generator was enabled. This is not an assurance of the stability of ECLK but is meant to provide a startup delay. This bit is forced clear when the clock monitor determines ECLK is inactive, when ECGON is clear, during stop mode with OSCENINSTOP low, or during reset. 1 = 4096 ECLK cycles have elapsed since ECGON was set. 0 = External clock is unstable, inactive, or disabled. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 115 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module 8.7.2 ICG Multiplier Register Address: $0037 Bit 7 Read: Write: Reset: 0 6 N6 0 = Unimplemented 5 N5 0 4 N4 1 3 N3 0 2 N2 1 1 N1 0 Bit 0 N0 1 Figure 8-13. ICG Multiplier Register (ICGMR) Freescale Semiconductor, Inc... N6:N0 -- ICG Multiplier Factor Bits These read/write bits change the multiplier used by the internal clock generator. The internal clock (ICLK) will be: (307.2 kHz 25 percent) * N A value of $00 in this register is interpreted the same as a value of $01. This register cannot be written when the CMON bit is set. Reset sets this factor to $15 (decimal 21) for default frequency of 6.45 MHz 25 percent (1.613 MHz 25 percent bus). 8.7.3 ICG Trim Register Address: $0038 Bit 7 Read: Write: Reset: TRIM7 1 6 TRIM6 0 5 TRIM5 0 4 TRIM4 0 3 TRIM3 0 2 TRIM2 0 1 TRIM1 0 Bit 0 TRIM0 0 Figure 8-14. ICG Trim Register (ICGTR) TRIM7:TRIM0 -- ICG Trim Factor Bits These read/write bits change the size of the internal capacitor used by the internal clock generator. By testing the frequency of the internal clock and incrementing or decrementing this factor accordingly, the accuracy of the internal clock can be improved (see 20.9.1 Trimmed Internal Clock Generator Characteristics). Incrementing this register by one decreases the frequency by 0.195 percent of the unadjusted value. Decrementing this register by one increases the frequency by 0.195 percent. This register cannot be written when the CMON bit is set. Reset sets these bits to $80, centering the range of possible adjustment. Data Sheet 116 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Input/Output (I/O) Registers 8.7.4 ICG DCO Divider Register Address: $0039 Bit 7 Read: Write: Reset: 0 0 = Unimplemented 0 0 U U = Unaffected U U U 6 5 4 3 DDIV3 2 DDIV2 1 DDIV1 Bit 0 DDIV0 Figure 8-15. ICG DCO Divider Control Register (ICGDVR) Freescale Semiconductor, Inc... DDIV3:DDIV0 -- ICG DCO Divider Control Bits These bits indicate the number of divide-by-twos (DDIV) that follow the digitally controlled oscillator. When ICGON is set, DDIV is controlled by the digital loop filter. The range of valid values for DDIV is from $0 to $9. Values of $A through $F are interpreted the same as $9. Since the DCO is active during reset, reset has no effect on DSTG and the value may vary. 8.7.5 ICG DCO Stage Register Address: $003A Bit 7 Read: Write: Reset: R = Reserved DSTG7 R 6 DSTG6 R 5 DSTG5 R 4 DSTG4 R 3 DSTG3 R 2 DSTG2 R 1 DSTG1 R Bit 0 DSTG0 R Unaffected by reset Figure 8-16. ICG DCO Stage Control Register (ICGDSR) DSTG7:DSTG0 -- ICG DCO Stage Control Bits These bits indicate the number of stages (above the minimum) in the digitally controlled oscillator. The total number of stages is approximately equal to $1FF, so changing DSTG from $00 to $FF will approximately double the period. Incrementing DSTG will increase the period (decrease the frequency) by 0.202 percent to 0.368 percent (decrementing has the opposite effect). DSTG cannot be written when ICGON is set to prevent inadvertent frequency shifting. When ICGON is set, DSTG is controlled by the digital loop filter. Since the DCO is active during reset, reset has no effect on DSTG and the value may vary. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Internal Clock Generator (ICG) Module Data Sheet 117 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Internal Clock Generator (ICG) Module Freescale Semiconductor, Inc... Data Sheet 118 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Internal Clock Generator (ICG) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 9. External Interrupt (IRQ) 9.1 Introduction This section describes the non-maskable external interrupt (IRQ) input. 9.2 Features Freescale Semiconductor, Inc... Features include: * * * * Dedicated external interrupt pin (IRQ) Hysteresis buffer Programmable edge-only or edge- and level-interrupt sensitivity Automatic interrupt acknowledge 9.3 Functional Description A logic 0 applied to the external interrupt pin can latch a central processor unit (CPU) interrupt request. Figure 9-1 shows the structure of the IRQ module. ACK INTERNAL ADDRESS BUS TO CPU FOR BIL/BIH INSTRUCTIONS VECTOR FETCH DECODER VDD D IRQ CLR Q SYNCHRONIZER IRQF CK IRQ LATCH IMASK IRQ INTERRUPT REQUEST MODE HIGH VOLTAGE DETECT TO MODE SELECT LOGIC Figure 9-1. IRQ Block Diagram MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA External Interrupt (IRQ) Data Sheet 119 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. External Interrupt (IRQ) Interrupt signals on the IRQ pin are latched into the IRQ latch. An interrupt latch remains set until one of these actions occurs: * * Vector fetch -- A vector fetch automatically generates an interrupt acknowledge signal that clears the latch that caused the vector fetch. Software clear -- Software can clear an interrupt latch by writing to the appropriate acknowledge bit in the interrupt status and control register (ISCR). Writing a 1 to the ACK bit clears the IRQ latch. Reset -- A reset automatically clears both interrupt latches. * Freescale Semiconductor, Inc... The external interrupt pin is falling-edge triggered and is software-configurable to be both falling-edge and low-level triggered. The MODE bit in the ISCR controls the triggering sensitivity of the IRQ pin. When an interrupt pin is edge-triggered only, the interrupt latch remains set until a vector fetch, software clear, or reset occurs. When an interrupt pin is both falling-edge and low-level-triggered, the interrupt latch remains set until both of these occur: * * Vector fetch or software clear Return of the interrupt pin to logic 1 The vector fetch or software clear may occur before or after the interrupt pin returns to logic 1. As long as the pin is low, the interrupt request remains pending. A reset will clear the latch and the MODE control bit, thereby clearing the interrupt even if the pin stays low. When set, the IMASK bit in the ISCR masks all external interrupt requests. A latched interrupt request is not presented to the interrupt priority logic unless the corresponding IMASK bit is clear. NOTE: The interrupt mask (I) in the condition code register (CCR) masks all interrupt requests, including external interrupt requests. See Figure 9-2. Data Sheet 120 External Interrupt (IRQ) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. External Interrupt (IRQ) Functional Description FROM RESET YES I BIT SET? NO INTERRUPT? YES Freescale Semiconductor, Inc... NO STACK CPU REGISTERS SET I BIT LOAD PC WITH INTERRUPT VECTOR FETCH NEXT INSTRUCTION SWI INSTRUCTION? NO YES RTI INSTRUCTION? NO YES UNSTACK CPU REGISTERS EXECUTE INSTRUCTION Figure 9-2. IRQ Interrupt Flowchart MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA External Interrupt (IRQ) Data Sheet 121 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. External Interrupt (IRQ) 9.4 IRQ Pin A logic 0 on the IRQ pin can latch an interrupt request into the IRQ latch. A vector fetch, software clear, or reset clears the IRQ latch. If the MODE bit is set, the IRQ pin is both falling-edge sensitive and low-level sensitive. With MODE set, both of these actions must occur to clear the IRQ latch: * Vector fetch or software clear -- A vector fetch generates an interrupt acknowledge signal to clear the latch. Software may generate the interrupt acknowledge signal by writing a 1 to the ACK bit in the interrupt status and control register (ISCR). The ACK bit is useful in applications that poll the IRQ pin and require software to clear the IRQ latch. Writing to the ACK bit can also prevent spurious interrupts due to noise. Setting ACK does not affect subsequent transitions on the IRQ pin. A falling edge on IRQ that occurs after writing to the ACK bit latches another interrupt request. If the IRQ mask bit, IMASK, is clear, the CPU loads the program counter with the vector address at locations $FFFA and $FFFB. Return of the IRQ pin to logic 1 -- As long as the IRQ pin is at logic 0, the IRQ latch remains set. Freescale Semiconductor, Inc... * The vector fetch or software clear and the return of the IRQ pin to logic 1 can occur in any order. The interrupt request remains pending as long as the IRQ pin is at logic 0. A reset will clear the latch and the MODE control bit, thereby clearing the interrupt even if the pin stays low. If the MODE bit is clear, the IRQ pin is falling-edge sensitive only. With MODE clear, a vector fetch or software clear immediately clears the IRQ latch. The IRQF bit in the ISCR register can be used to check for pending interrupts. The IRQF bit is not affected by the IMASK bit, which makes it useful in applications where polling is preferred. Use the BIH or BIL instruction to read the logic level on the IRQ pin. NOTE: When using the level-sensitive interrupt trigger, avoid false interrupts by masking interrupt requests in the interrupt routine. 9.5 IRQ Module During Break Interrupts The system integration module (SIM) controls whether the IRQ interrupt latch can be cleared during the break state. The BCFE bit in the SIM break flag control register (SBFCR) enables software to clear the latches during the break state. To allow software to clear the IRQ latch during a break interrupt, write a 1 to the BCFE bit. If a latch is cleared during the break state, it remains cleared when the MCU exits the break state. Data Sheet 122 External Interrupt (IRQ) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. External Interrupt (IRQ) IRQ Status and Control Register To protect the latch during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default state), writing to the ACK bit in the IRQ status and control register during the break state has no effect on the IRQ latch. 9.6 IRQ Status and Control Register The IRQ status and control register (ISCR) controls and monitors operation of the IRQ module. The ISCR has these functions: * * * * Shows the state of the IRQ interrupt flag Clears the IRQ interrupt latch Masks IRQ interrupt request Controls triggering sensitivity of the IRQ interrupt pin Address: Read: Write: Reset: $001D Bit 7 0 R 0 R 6 0 R 0 = Reserved 5 0 R 0 4 0 R 0 3 IRQF R 0 2 0 ACK 0 1 IMASK 0 Bit 0 MODE 0 Freescale Semiconductor, Inc... Figure 9-3. IRQ Status and Control Register (ISCR) IRQF -- IRQ Flag Bit This read-only status bit is high when the IRQ interrupt is pending. 1 = IRQ interrupt pending 0 = IRQ interrupt not pending ACK -- IRQ Interrupt Request Acknowledge Bit Writing a 1 to this write-only bit clears the IRQ latch. ACK always reads as 0. Reset clears ACK. IMASK -- IRQ Interrupt Mask Bit Writing a 1 to this read/write bit disables IRQ interrupt requests. Reset clears IMASK. 1 = IRQ interrupt requests disabled 0 = IRQ interrupt requests enabled MODE -- IRQ Edge/Level Select Bit This read/write bit controls the triggering sensitivity of the IRQ pin. Reset clears MODE. 1 = IRQ interrupt requests on falling edges and low levels 0 = IRQ interrupt requests on falling edges only MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA External Interrupt (IRQ) Data Sheet 123 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. External Interrupt (IRQ) Freescale Semiconductor, Inc... Data Sheet 124 External Interrupt (IRQ) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 10. Keyboard Interrupt (KBD) Module 10.1 Introduction The keyboard interrupt (KBD) module provides five independently maskable external interrupt pins. Freescale Semiconductor, Inc... 10.2 Features KBD features include: * Five keyboard interrupt pins (PTA4/KBD4-PTA0/KBD0) with internal pullups, with separate keyboard interrupt enable bits and one keyboard interrupt mask Hysteresis buffers Programmable edge only or edge and level interrupt sensitivity Automatic interrupt acknowledge Exit from low-power modes * * * * 10.3 Functional Description Writing to the KBIE4-KBIE0 bits in the keyboard interrupt enable register independently enables or disables each port as a keyboard interrupt pin. Enabling a keyboard interrupt pin also enables its internal pullup device. A logic 0 applied to an enabled keyboard interrupt pin latches a keyboard interrupt request. A keyboard interrupt is latched when one or more keyboard pins goes low after all were high. The MODEK bit in the keyboard status and control register controls the triggering mode of the keyboard interrupt. * If the keyboard interrupt is edge-sensitive only, a falling edge on a keyboard pin does not latch an interrupt request if another keyboard pin is already low. To prevent losing an interrupt request on one pin because another pin is still low, software can disable the latter pin while it is low. If the keyboard interrupt is falling edge- and low level-sensitive, an interrupt request is present as long as any keyboard pin is low. * MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Keyboard Interrupt (KBD) Module Data Sheet 125 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Keyboard Interrupt (KBD) Module INTERNAL BUS M68HC08 CPU CPU REGISTERS ARITHMETIC/LOGIC UNIT (ALU) SINGLE BREAKPOINT BREAK MODULE PORT A DDRA 5-BIT KEYBOARD INTERRUPT MODULE PTA6/SS PTA5/SPSCK PTA4/KBD4 PTA3/KBD3 PTA2/KBD2 PTA1/KBD 2-CHANNEL TIMER INTERFACE MODULE A PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PORT B DDRB PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK PTC1/MOSI PTC0/MISO PTD1/TACH1 PTD0/TACH0 PTE1/RxD PTE0/TxD PORT C PORT E PORT D CONTROL AND STATUS REGISTERS 64 BYTES USER FLASH 15,872 BYTES USER RAM 512 BYTES Freescale Semiconductor, Inc... MONITOR ROM 310 BYTES FLASH PROGRAMMING (BURN-IN) ROM 1024 BYTES USER FLASH VECTOR SPACE 36 BYTES 2-CHANNEL TIMER INTERFACE MODULE B ENHANCED SERIAL COMMUNICATION INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE OSC2 OSC1 INTERNAL CLOCK GENERATOR MODULE SERIAL PERIPHERAL INTERFACE MODULE RST 24 INTERNAL SYSTEM INTEGRATION MODULE SINGLE EXTERNAL IRQ MODULE CONFIGURATION REGISTER MODULE PERIODIC WAKEUP TIMEBASE MODULE ARBITER MODULE PRESCALER MODULE IRQ VREFH VDDA VREFL VSSA VDD VSS DDRE DDRD DDRC 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE SECURITY MODULE POWER BEMF MODULE Figure 10-1. Block Diagram Highlighting Keyboard Block and Pins Data Sheet 126 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Keyboard Interrupt (KBD) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Keyboard Interrupt (KBD) Module Functional Description INTERNAL BUS KBD0 VDD TO PULLUP ENABLE KB0IE . . . D CLR Q ACKK RESET VECTOR FETCH DECODER KEYF SYNCHRONIZER CK Freescale Semiconductor, Inc... KBD4 KEYBOARD INTERRUPT FF IMASKK KEYBOARD INTERRUPT REQUEST TO PULLUP ENABLE KB4IE MODEK Figure 10-2. Keyboard Module Block Diagram Addr. Register Name Keyboard Status Read: and Control Register Write: (KBSCR) See page 130. Reset: Keyboard Interrupt Read: Enable Register Write: (KBIER) See page 131. Reset: Bit 7 0 6 0 5 0 4 0 3 KEYF 2 0 ACKK 1 IMASKK 0 KBIE1 0 Bit 0 MODEK 0 KBIE0 0 $001A 0 0 0 0 0 0 0 KBIE4 0 0 KBIE3 0 0 KBIE2 0 $001B 0 0 = Unimplemented 0 Figure 10-3. KBD I/O Register Summary If the MODEK bit is set, the keyboard interrupt pins are both falling edge and low level sensitive, and both of the following actions must occur to clear a keyboard interrupt request: * Vector fetch or software clear -- A vector fetch generates an interrupt acknowledge signal to clear the interrupt request. Software may generate the interrupt acknowledge signal by writing a 1 to the ACKK bit in the keyboard status and control register (KBSCR). The ACKK bit is useful in applications that poll the keyboard interrupt pins and require software to clear the keyboard interrupt request. Writing to the ACKK bit prior to leaving an interrupt service routine also can prevent spurious interrupts due to noise. Setting ACKK does not affect subsequent transitions on the keyboard interrupt pins. A falling edge that occurs after writing to the ACKK bit latches MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Keyboard Interrupt (KBD) Module Data Sheet 127 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Keyboard Interrupt (KBD) Module another interrupt request. If the keyboard interrupt mask bit, IMASKK, is clear, the CPU loads the program counter with the vector address at locations $FFE4 and $FFE5. * Return of all enabled keyboard interrupt pins to logic 1. As long as any enabled keyboard interrupt pin is at logic 0, the keyboard interrupt remains set. The vector fetch or software clear and the return of all enabled keyboard interrupt pins to logic 1 may occur in any order. If the MODEK bit is clear, the keyboard interrupt pin is falling edge-sensitive only. With MODEK clear, a vector fetch or software clear immediately clears the keyboard interrupt request. Reset clears the keyboard interrupt request and the MODEK bit, clearing the interrupt request even if a keyboard interrupt pin stays at logic 0. The keyboard flag bit (KEYF) in the keyboard status and control register can be used to see if a pending interrupt exists. The KEYF bit is not affected by the keyboard interrupt mask bit (IMASKK) which makes it useful in applications where polling is preferred. To determine the logic level on a keyboard interrupt pin, use the data direction register to configure the pin as an input and read the data register. NOTE: Setting a keyboard interrupt enable bit (KBIEx) forces the corresponding keyboard interrupt pin to be an input, overriding the data direction register. However, the data direction register bit must be a 0 for software to read the pin. Freescale Semiconductor, Inc... 10.4 Keyboard Initialization When a keyboard interrupt pin is enabled, it takes time for the internal pullup to reach a logic 1. Therefore, a false interrupt can occur as soon as the pin is enabled. To prevent a false interrupt on keyboard initialization: 1. Mask keyboard interrupts by setting the IMASKK bit in the keyboard status and control register 2. Enable the KBI pins by setting the appropriate KBIEx bits in the keyboard interrupt enable register 3. Write to the ACKK bit in the keyboard status and control register to clear any false interrupts 4. Clear the IMASKK bit. An interrupt signal on an edge-triggered pin can be acknowledged immediately after enabling the pin. An interrupt signal on an edge- and level-triggered interrupt pin must be acknowledged after a delay that depends on the external load. Data Sheet 128 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Keyboard Interrupt (KBD) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Keyboard Interrupt (KBD) Module Low-Power Modes Another way to avoid a false interrupt: 1. Configure the keyboard pins as outputs by setting the appropriate DDRA bits in data direction register A. 2. Write 1s to the appropriate port A data register bits. 3. Enable the KBI pins by setting the appropriate KBIEx bits in the keyboard interrupt enable register. 10.5 Low-Power Modes The WAIT and STOP instructions put the microcontroller unit (MCU) in low power-consumption standby modes. Freescale Semiconductor, Inc... 10.5.1 Wait Mode The keyboard module remains active in wait mode. Clearing the IMASKK bit in the keyboard status and control register enables keyboard interrupt requests to bring the MCU out of wait mode. 10.5.2 Stop Mode The keyboard module remains active in stop mode. Clearing the IMASKK bit in the keyboard status and control register enables keyboard interrupt requests to bring the MCU out of stop mode. 10.6 Keyboard Module During Break Interrupts The BCFE bit in the break flag control register (SBFCR) enables software to clear status bits during the break state. To allow software to clear the KEYF bit during a break interrupt, write a 1 to the BCFE bit. If KEYF is cleared during the break state, it remains cleared when the MCU exits the break state. To protect the KEYF bit during the break state, write a 0 to the BCFE bit. With BCFE at 0, writing to the keyboard acknowledge bit (ACKK) in the keyboard status and control register during the break state has no effect. See 10.7.1 Keyboard Status and Control Register. 10.7 I/O Registers These registers control and monitor operation of the keyboard module: * * Keyboard status and control register, KBSCR Keyboard interrupt enable register, KBIER MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Keyboard Interrupt (KBD) Module Data Sheet 129 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Keyboard Interrupt (KBD) Module 10.7.1 Keyboard Status and Control Register The keyboard status and control register: * * * * Flags keyboard interrupt requests Acknowledges keyboard interrupt requests Masks keyboard interrupt requests Controls keyboard interrupt triggering sensitivity Address: $001A Bit 7 6 0 0 5 0 0 4 0 0 3 KEYF 0 2 0 ACKK 0 0 = Unimplemented 1 IMASKK 0 Bit 0 MODEK 0 Freescale Semiconductor, Inc... Read: Write: Reset: 0 Figure 10-4. Keyboard Status and Control Register (KBSCR) Bits 7-4 -- Not used These read-only bits always read as 0s. KEYF -- Keyboard Flag Bit This read-only bit is set when a keyboard interrupt is pending. Reset clears the KEYF bit. 1 = Keyboard interrupt pending 0 = No keyboard interrupt pending ACKK -- Keyboard Acknowledge Bit Writing a 1 to this write-only bit clears the keyboard interrupt request. ACKK always reads as 0. Reset clears ACKK. IMASKK -- Keyboard Interrupt Mask Bit Writing a 1 to this read/write bit prevents the output of the keyboard interrupt mask from generating interrupt requests. Reset clears the IMASKK bit. 1 = Keyboard interrupt requests masked 0 = Keyboard interrupt requests not masked MODEK -- Keyboard Triggering Sensitivity Bit This read/write bit controls the triggering sensitivity of the keyboard interrupt pins. Reset clears MODEK. 1 = Keyboard interrupt requests on falling edges and low levels 0 = Keyboard interrupt requests on falling edges only Data Sheet 130 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Keyboard Interrupt (KBD) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Keyboard Interrupt (KBD) Module I/O Registers 10.7.2 Keyboard Interrupt Enable Register The keyboard interrupt enable register enables or disables each port A pin to operate as a keyboard interrupt pin. Address: $001B Bit 7 Read: Write: Reset: 0 0 = Unimplemented 0 0 6 0 5 0 4 KBIE4 0 3 KBIE3 0 2 KBIE2 0 1 KBIE1 0 Bit 0 KBIE0 0 Freescale Semiconductor, Inc... Figure 10-5. Keyboard Interrupt Enable Register (KBIER) KBIE4-KBIE0 -- Keyboard Interrupt Enable Bits Each of these read/write bits enables the corresponding keyboard interrupt pin to latch interrupt requests. Reset clears the keyboard interrupt enable register. 1 = PDx pin enabled as keyboard interrupt pin 0 = PDx pin not enabled as keyboard interrupt pin MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Keyboard Interrupt (KBD) Module Data Sheet 131 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Keyboard Interrupt (KBD) Module Freescale Semiconductor, Inc... Data Sheet 132 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Keyboard Interrupt (KBD) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 11. Low-Voltage Inhibit (LVI) Module 11.1 Introduction This section describes the low-voltage inhibit (LVI) module, which monitors the voltage on the VDD pin and can force a reset when the VDD voltage falls to the LVI trip voltage. Freescale Semiconductor, Inc... 11.2 Features Features include: * * * Programmable LVI reset Programmable power consumption 3 V or 5 V selectable trip point 11.3 Functional Description Figure 11-1 shows the structure of the LVI module. The LVI is enabled out of reset. The LVI module contains a bandgap reference circuit and comparator. The LVI power bit, LVIPWRD, enables the LVI to monitor VDD voltage. The LVI reset bit, LVIRSTD, enables the LVI module to generate a reset when VDD falls below a voltage, LVITRIPF. LVISTOP, enables the LVI module during stop mode. This will ensure when the STOP instruction is implemented, the LVI will continue to monitor the voltage level on VDD. LVIPWRD, LVISTOP, and LVIRSTD are in the configuration register (CONFIG-1). See Section 5. Configuration Registers (CONFIG1 and CONFIG2). Once an LVI reset occurs, the MCU remains in reset until VDD rises above a voltage, LVITRIPR. VDD must be above LVITRIPR for only one CPU cycle to bring the MCU out of reset (see 11.3.2 Forced Reset Operation). The output of the comparator controls the state of the LVIOUT flag in the LVI status register (LVISR). An LVI reset also drives the RST pin low to provide low-voltage protection to external peripheral devices. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Low-Voltage Inhibit (LVI) Module Data Sheet 133 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Low-Voltage Inhibit (LVI) Module VDD STOP INSTRUCTION LVISTOP FROM CONFIG-1 FROM CONFIG-1 LVIRSTD LVIPWRD FROM CONFIG-1 LOW VDD DETECTOR VDD > LVITRIPR = 0 VDD < LVITRIPF = 1 LVI RESET Freescale Semiconductor, Inc... LVI5OR3 FROM CONFIG-1 LVIOUT Figure 11-1. LVI Module Block Diagram 11.3.1 Polled LVI Operation In applications that can operate at VDD levels below the LVITRIPF level, software can monitor VDD by polling the LVIOUT bit. In the configuration register, the LVIPWRD bit must be at 1 to enable the LVI module, and the LVIRSTD bit must be at 0 to disable LVI resets. 11.3.2 Forced Reset Operation In applications that require VDD to remain above the LVITRIPF level, enabling LVI resets allows the LVI module to reset the MCU when VDD falls to the LVITRIPF level. In the configuration register, the LVIPWRD and LVIRSTD bits must be at 1 to enable the LVI module and to enable LVI resets. 11.3.3 False Reset Protection False reset protection is provided by the hysteresis in the LVI trip circuit (refer to Table 11-1). Please refer to 20.5 DC Electrical Characteristics for hysteresis value (VHYS) and rising and falling LVI trip values. Data Sheet 134 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Low-Voltage Inhibit (LVI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Low-Voltage Inhibit (LVI) Module LVI Interrupts 11.3.4 LVI Status Register The LVI status register flags VDD voltages below the LVITRIPF level. Address: Read: Write: Reset: 0 0 0 0 0 0 0 0 = Unimplemented $FE0C Bit 7 LVIOUT 6 0 5 0 4 0 3 0 2 0 1 0 Bit 0 0 Figure 11-2. LVI Status Register (LVISR) Freescale Semiconductor, Inc... LVIOUT -- LVI Output Bit This read-only flag becomes set when the VDD voltage falls below the LVITRIPF voltage for 32 to 40 CGMXCLK cycles. (See Table 11-1.) Reset clears the LVIOUT bit. Table 11-1. LVIOUT Bit Indication VDD At Level: VDD > LVITRIPR VDD < LVITRIPF LVITRIPF < VDD < LVITRIPR 0 1 Previous Value LVIOUT 11.4 LVI Interrupts The LVI module does not generate interrupt requests. 11.5 Low-Power Modes The WAIT and STOP instructions put the microcontroller unit (MCU) in low power-consumption standby modes. 11.5.1 Wait Mode With the LVIPWRD bit in the configuration register programmed to 1, the LVI module is active after a WAIT instruction. With the LVIRSTD bit in the configuration register programmed to 1, the LVI module can generate a reset and bring the MCU out of wait mode. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Low-Voltage Inhibit (LVI) Module Data Sheet 135 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Low-Voltage Inhibit (LVI) Module 11.5.2 Stop Mode With the LVISTOP and LVIPWRD bits in the configuration register programmed to a 1, the LVI module will be active after a STOP instruction. With the LVIPWRD bit in the configuration register programmed to 1 and the LVISTOP bit at a 0, the LVI module will be inactive after a STOP instruction. Freescale Semiconductor, Inc... Data Sheet 136 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Low-Voltage Inhibit (LVI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 12. Input/Output (I/O) Ports (PORTS) 12.1 Introduction Twenty-four bidirectional input/output (I/O) pins form five parallel ports. All I/O pins are programmable as inputs or outputs. NOTE: Freescale Semiconductor, Inc... Connect any unused I/O pins to an appropriate logic level, either VDD or VSS. Although the I/O ports do not require termination for proper operation, termination reduces excess current consumption and the possibility of electrostatic damage. Addr. $0000 Register Name Port A Data Register Read: (PTA) Write: See page 138. Reset: Port B Data Register Read: (PTB) Write: See page 140. Reset: Port C Data Register Read: (PTC) Write: See page 143. Reset: Port D Data Register Read: (PTD) Write: See page 145. Reset: Data Direction Register A Read: (DDRA) Write: See page 139. Reset: Data Direction Register B Read: (DDRB) Write: See page 141. Reset: Bit 7 0 6 PTA6 5 PTA5 4 PTA4 3 PTA3 2 PTA2 1 PTA1 Bit 0 PTA0 Unaffected by reset PTB7 PTB6 PTB5 PTB4 PTB3 PTB2 PTB1 PTB0 $0001 Unaffected by reset 0 0 0 PTC4 PTC3 PTC2 PTC1 PTC0 $0002 Unaffected by reset 0 0 0 0 0 0 PTD1 PTD0 $0003 Unaffected by reset 0 0 DDRB7 0 DDRA6 0 DDRB6 0 0 0 0 0 = Unimplemented DDRA5 0 DDRB5 0 0 0 0 0 DDRA4 0 DDRB4 0 DDRC4 0 0 0 DDRA3 0 DDRB3 0 DDRC3 0 0 0 DDRA2 0 DDRB2 0 DDRC2 0 0 0 DDRA1 0 DDRB1 0 DDRC1 0 DDRD1 0 DDRA0 0 DDRB0 0 DDRC0 0 DDRD0 0 $0004 $0005 $0006 Data Direction Register C Read: MCLKEN (DDRC) Write: See page 143. Reset: 0 Data Direction Register D Read: (DDRD) Write: See page 145. Reset: 0 0 $0007 Figure 12-1. I/O Port Register Summary MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Input/Output (I/O) Ports (PORTS) Data Sheet 137 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Input/Output (I/O) Ports (PORTS) Addr. $0008 Register Name Port E Data Register Read: (PTE) Write: See page 147. Reset: Data Direction Register E Read: (DDRE) Write: See page 147. Reset: BEMF Register Read: (BEMF) Write: See page 61. Reset: Bit 7 0 6 0 5 0 4 0 3 0 2 0 1 PTE1 Bit 0 PTE0 Unaffected by reset 0 0 BEMF7 0 0 0 BEMF6 0 = Unimplemented 0 0 BEMF5 0 0 0 BEMF4 0 0 0 BEMF3 0 0 0 BEMF2 0 DDRE1 0 BEMF1 0 DDRE0 0 BEMF0 0 $000A $000B Freescale Semiconductor, Inc... Figure 12-1. I/O Port Register Summary (Continued) 12.2 Port A Port A is a 7-bit general-purpose bidirectional I/O port that shares pin functions with the serial peripheral interface (SPI) and keyboard (KBD) modules. 12.2.1 Port A Data Register The port A data register contains a data latch for each of the seven port A pins. Address: Read: Write: Reset: Alternate Function: SS SPSCK $0000 Bit 7 0 6 PTA6 5 PTA5 4 PTA4 3 PTA3 2 PTA2 1 PTA1 Bit 0 PTA0 Unaffected by reset KBD4 KBD3 KBD2 KBD1 KBD0 = Unimplemented Figure 12-2. Port A Data Register (PTA) PTA[6:0] -- Port A Data Bits These read/write bits are software programmable. Data direction of each port A pin is under the control of the corresponding bit in data direction register A. Reset has no effect on port A data. Data Sheet 138 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Input/Output (I/O) Ports (PORTS) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Input/Output (I/O) Ports (PORTS) Port A 12.2.2 Data Direction Register A Data direction register A determines whether each port A pin is an input or an output. Writing a 1 to a DDRA bit enables the output buffer for the corresponding port A pin; a 0 disables the output buffer. Address: Read: Write: Reset: $0004 Bit 7 0 6 DDRA6 5 DDRA5 4 DDRA4 3 DDRA3 2 DDRA2 1 DDRA1 Bit 0 DDRA0 Unaffected by reset = Unimplemented Freescale Semiconductor, Inc... Figure 12-3. Data Direction Register A (DDRA) DDRA[6:0] -- Data Direction Register A Bits These read/write bits control port A data direction. Reset clears DDRA[6:0], configuring all port A pins as inputs. 1 = Corresponding port A pin configured as output 0 = Corresponding port A pin configured as input NOTE: Avoid glitches on port A pins by writing to the port A data register before changing data direction register A bits from 0 to 1. Figure 12-4 shows the port A I/O logic. READ DDRA ($0004) WRITE DDRA ($0004) INTERNAL DATA BUS RESET WRITE PTA ($0000) PTAx PTAx DDRAx READ PTA ($0000) Figure 12-4. Port A I/O Circuit When bit DDRAx is a 1, reading address $0000 reads the PTAx data latch. When bit DDRAx is a 0, reading address $0000 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-1 summarizes the operation of the port A pins. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Input/Output (I/O) Ports (PORTS) Data Sheet 139 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Input/Output (I/O) Ports (PORTS) Table 12-1. Port A Pin Functions DDRA Bit 0 1 PTA Bit X X I/O Pin Mode Input, Hi-Z Output Accesses to DDRA Read/Write DDRA[6:0] DDRA[6:0] Accesses to PTA Read Pin PTA[6:0] Write PTA[6:0](1) PTA[6:0] X = don't care Hi-Z = high impedance 1. Writing affects data register, but does not affect input. 12.3 Port B Freescale Semiconductor, Inc... Port B is an 8-bit special-function port that shares all of its pins with the analog-to-digital converter (ADC) and some pin functions with TIMB. Port B is designed so that the ADC function will take priority over the timer functionality on PTB6 and PTB7. If the ADC is selected for a conversion on a previously enabled timer pin, the port pin will be connected to the ADC and disconnected from the timer. If both the timer input capture and ADC functions are being used on the same port pin, it is recommended that the timer channel be diabled before the pin is enabled as an ADC input to avoid glitches. If both the timer output compare (or PWM) and ADC functions are being used on the same port pin, it is recommended that the timer channel be disabled before the pin is enabled as an ADC input. 12.3.1 Port B Data Register The port B data register contains a data latch for each of the eight port B pins. Address: Read: Write: Reset: Alternate Functions: Alternate Function: ATD7 TBCH1 ATD6 TBCH0 ATD5 $0001 Bit 7 PTB7 6 PTB6 5 PTB5 4 PTB4 3 PTB3 2 PTB2 1 PTB1 Bit 0 PTB0 Unaffected by reset ATD4 ATD3 ATD2 ATD1 ATD0 Figure 12-5. Port B Data Register (PTB) PTB[7:0] -- Port B Data Bits These read/write bits are software programmable. Data direction of each port B pin is under the control of the corresponding bit in data direction register B. Reset has no effect on port B data. Data Sheet 140 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Input/Output (I/O) Ports (PORTS) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Input/Output (I/O) Ports (PORTS) Port B ATD[7:0] -- ADC Channels PTB7-PTB0 are eight of the 15 ADC channels. The ADC channel select bits, CH[4:0], determine whether the PTB7-PTB0 pins are ADC channels or general-purpose I/O pins. If an ADC channel is selected and a read of this corresponding bit in the port B data register occurs, the data will be a 0 if the data direction for this bit is programmed as an input. Otherwise, the data will reflect the value in the data latch (see Section 3. Analog-to-Digital Converter (ADC) Module). DDRB does not affect the data direction of port B pins that are being used by the ADC. However, the DDRB bits always determine whether reading port B returns to the states of the latches or 0. Freescale Semiconductor, Inc... TBCH[1:0] -- Timer Channel I/O Bits The PTB7/TBCH1-PTB6/TBCH0 pins are the TIMB input capture/output compare pins. The edge/level select bits, ELSxB-ELSxA, determine whether the PTB7/TBCH1-PTB6/TBCH0 pins are timer channel I/O pins or general-purpose I/O pins. See 18.8.1 TIMB Status and Control Register. NOTE: Data direction register B (DDRB) does not affect the data direction of port B pins that are being used by the TIMB. However, the DDRB bits always determine whether reading port B returns the states of the latches or the states of the pins. See Table 12-2. 12.3.2 Data Direction Register B Data direction register B determines whether each port B pin is an input or an output. Writing a 1 to a DDRB bit enables the output buffer for the corresponding port B pin; a 0 disables the output buffer. Address: Read: Write: Reset: $0005 Bit 7 DDRB7 0 6 DDRB6 0 5 DDRB5 0 4 DDRB4 0 3 DDRB3 0 2 DDRB2 0 1 DDRB1 0 Bit 0 DDRB0 0 Figure 12-6. Data Direction Register B (DDRB) DDRB[7:0] -- Data Direction Register B Bits These read/write bits control port B data direction. Reset clears DDRB[7:0], configuring all port B pins as inputs. 1 = Corresponding port B pin configured as output 0 = Corresponding port B pin configured as input NOTE: Avoid glitches on port B pins by writing to the port B data register before changing data direction register B bits from 0 to 1. Figure 12-7 shows the port B I/O logic. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Input/Output (I/O) Ports (PORTS) Data Sheet 141 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Input/Output (I/O) Ports (PORTS) READ DDRB ($0005) WRITE DDRB ($0005) INTERNAL DATA BUS RESET WRITE PTB ($0001) PTBx PTBx DDRBx READ PTB ($0001) Freescale Semiconductor, Inc... Figure 12-7. Port B I/O Circuit When DDRBx is a 1, reading address $0001 reads the PTBx data latch. When DDRBx is a 0, reading address $0001 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-2 summarizes the operation of the port B pins. Table 12-2. Port B Pin Functions DDRB Bit 0 1 PTB Bit X X I/O Pin Mode Input, Hi-Z Output Accesses to DDRB Read/Write DDRB[7:0] DDRB[7:0] Accesses to PTB Read Pin PTB[7:0] Write PTB[7:0](1) PTB[7:0] X = don't care Hi-Z = high impedance 1. Writing affects data register, but does not affect input. 12.4 Port C Port C is an 5-bit general-purpose bidirectional I/O port that shares pin functions with the internal clock generator (ICG) and serial peripheral interface (SPI) modules. Data Sheet 142 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Input/Output (I/O) Ports (PORTS) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Input/Output (I/O) Ports (PORTS) Port C 12.4.1 Port C Data Register The port C data register contains a data latch for each of the five port C pins. Address: Read: Write: Reset: Alternate Functions: $0002 Bit 7 0 6 0 5 0 4 PTC4 3 PTC3 2 PTC2 1 PTC1 Bit 0 PTC0 Unaffected by reset OSC1 = Unimplemented OSC2 MCLK MOSI MISO Freescale Semiconductor, Inc... Figure 12-8. Port C Data Register (PTC) PTC[4:0] -- Port C Data Bits These read/write bits are software-programmable. Data direction of each port C pin is under the control of the corresponding bit in data direction register C. Reset has no effect on port C data. MCLK -- T12 System Clock Bit The system clock is driven out of PTC2 when enabled by MCLKEN bit in PTCDDR7. 12.4.2 Data Direction Register C Data direction register C determines whether each port C pin is an input or an output. Writing a 1 to a DDRC bit enables the output buffer for the corresponding port C pin; a 0 disables the output buffer. Address: Read: Write: Reset: $0006 Bit 7 MCLKEN 0 6 0 0 5 0 0 4 DDRC4 0 3 DDRC3 0 2 DDRC2 0 1 DDRC1 0 Bit 0 DDRC0 0 = Unimplemented Figure 12-9. Data Direction Register C (DDRC) MCLKEN -- MCLK Enable Bit This read/write bit enables MCLK to be an output signal on PTC2. If MCLK is enabled, PTC2 is under the control of MCLKEN. Reset clears this bit. 1 = MCLK output enabled 0 = MCLK output disabled MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Input/Output (I/O) Ports (PORTS) Data Sheet 143 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Input/Output (I/O) Ports (PORTS) DDRC[4:0] -- Data Direction Register C Bits These read/write bits control port C data direction. Reset clears DDRC[4:0] and MCLKEN, configuring all port C pins as inputs. 1 = Corresponding port C pin configured as output 0 = Corresponding port C pin configured as input NOTE: Avoid glitches on port C pins by writing to the port C data register before changing data direction register C bits from 0 to 1. Figure 12-10 shows the port C I/O logic. READ DDRC ($0006) Freescale Semiconductor, Inc... WRITE DDRC ($0006) INTERNAL DATA BUS RESET WRITE PTC ($0002) PTCx PTCx DDRCx READ PTC ($0002) Figure 12-10. Port C I/O Circuit When bit DDRCx is a 1, reading address $0002 reads the PTCx data latch. When bit DDRCx is a 0, reading address $0002 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-3 summarizes the operation of the port C pins. Table 12-3. Port C Pin Functions DDRC Bit 0 1 0 1 PTC Bit 2 2 X X I/O Pin Mode Input, Hi-Z Output Input, Hi-Z Output Accesses to DDRC Read/Write DDRC[7] DDRC[7] DDRC[4:0] DDRC[4:0] Accesses to PTC Read Pin 0 Pin PTC[4:0] Write PTC2 -- PTC[4:0](1) PTC[4:0] X = don't care Hi-Z = high impedance 1. Writing affects data register, but does not affect input. Data Sheet 144 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Input/Output (I/O) Ports (PORTS) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Input/Output (I/O) Ports (PORTS) Port D 12.5 Port D Port D is an 2-bit special function port that shares its pins with the timer interface module (TIMA). 12.5.1 Port D Data Register The port D data register contains a data latch for each of the two port D pins. Address: Read: Write: Reset: Alternate Function: = Unimplemented Unaffected by reset TACH1 TACH0 $0003 Bit 7 6 0 5 0 4 0 3 0 2 0 1 PTD1 Bit 0 PTD0 0 Freescale Semiconductor, Inc... Figure 12-11. Port D Data Register (PTD) PTD[1:0] -- Port D Data Bits PTD[1:0] are read/write, software programmable bits. Data direction of each port D pin is under the control of the corresponding bit in data direction register D. TACH[1:0] -- Timer Channel I/O Bits The PTD1/TACH1-PTD0/TACH0 pins are the TIMA input capture/output compare pins. The edge/level select bits, ELSxB-ELSxA, determine whether the PTD1/TACH1-PTD0/TACH0 pins are timer channel I/O pins or general-purpose I/O pins. See 17.8.1 TIMA Status and Control Register. NOTE: Data direction register D (DDRD) does not affect the data direction of port D pins that are being used by the TIMA. However, the DDRD bits always determine whether reading port D returns the states of the latches or the states of the pins. See Table 12-4. 12.5.2 Data Direction Register D Data direction register D determines whether each port D pin is an input or an output. Writing a 1 to a DDRD bit enables the output buffer for the corresponding port D pin; a 0 disables the output buffer. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Input/Output (I/O) Ports (PORTS) Data Sheet 145 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Input/Output (I/O) Ports (PORTS) Address: Read: Write: Reset: $0007 Bit 7 0 0 6 0 0 5 0 0 4 0 0 3 0 0 2 0 0 1 DDRD1 0 Bit 0 DDRD0 0 = Unimplemented Figure 12-12. Data Direction Register D (DDRD) DDRD[1:0] -- Data Direction Register D Bits These read/write bits control port D data direction. Reset clears DDRD[1:0], configuring all port D pins as inputs. 1 = Corresponding port D pin configured as output 0 = Corresponding port D pin configured as input NOTE: Avoid glitches on port D pins by writing to the port D data register before changing data direction register D bits from 0 to 1. Figure 12-13 shows the port D I/O logic. READ DDRD ($0007) Freescale Semiconductor, Inc... WRITE DDRD ($0007) INTERNAL DATA BUS RESET WRITE PTD ($0003) PTDx PTDx DDRDx READ PTD ($0003) Figure 12-13. Port D I/O Circuit When bit DDRDx is a 1, reading address $0003 reads the PTDx data latch. When bit DDRDx is a 0, reading address $0003 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-4 summarizes the operation of the port D pins. Table 12-4. Port D Pin Functions DDRD Bit 0 1 PTD Bit X X I/O Pin Mode Input, Hi-Z Output Accesses to DDRD Read/Write DDRD[1:0] DDRD[1:0] Accesses to PTD Read Pin PTD[1:0] Write PTD[1:0](1) PTD[1:0] X = don't care Hi-Z = high impedance 1. Writing affects data register, but does not affect input. Data Sheet 146 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Input/Output (I/O) Ports (PORTS) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Input/Output (I/O) Ports (PORTS) Port E 12.6 Port E Port E is a 2-bit special function port that shares its pins with the enhanced serial communications interface module (ESCI). 12.6.1 Port E Data Register The port E data register contains a data latch for each of the port E pins. Address: Read: Write: Reset: Alternate Function: 0 0 0 Unaffected by reset 0 0 0 RXD TXD $0008 Bit 7 6 0 5 0 4 0 3 0 2 0 1 PTE1 Bit 0 PTE0 0 Freescale Semiconductor, Inc... = Unimplemented Figure 12-14. Port E Data Register (PTE) PTE[1:0] -- Port E Data Bits These read/write bits are software programmable. Data direction of each port E pin is under the control of the corresponding bit in data direction register E. Reset has no effect on PTE[1:0]. RxD -- SCI Receive Data Input Bit The PTE1/RxD pin is the receive data input for the SCI module. When the enable SCI bit, ENSCI, is clear, the SCI module is disabled, and the PTE1/RxD pin is available for general-purpose I/O. See 13.8.1 ESCI Control Register 1. TxD -- SCI Transmit Data Output The PTE0/TxD pin is the transmit data output for the SCI module. When the enable SCI bit, ENSCI, is clear, the SCI module is disabled, and the PTE0/TxD pin is available for general-purpose I/O. See 13.8.1 ESCI Control Register 1. NOTE: Data direction register E (DDRE) does not affect the data direction of port E pins that are being used by the ESCI. However, the DDRE bits always determine whether reading port E returns the states of the latches or the states of the pins. See Table 12-5. 12.6.2 Data Direction Register E Data direction register E determines whether each port E pin is an input or an output. Writing a 1 to a DDRE bit enables the output buffer for the corresponding port E pin; a 0 disables the output buffer. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Input/Output (I/O) Ports (PORTS) Data Sheet 147 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Input/Output (I/O) Ports (PORTS) Address: Read: Write: Reset: $000A Bit 7 0 0 6 0 0 5 0 0 4 0 0 3 0 0 2 0 0 1 DDRE1 0 Bit 0 DDRE0 0 = Unimplemented Figure 12-15. Data Direction Register E (DDRE) DDRE[1:0] -- Data Direction Register E Bits These read/write bits control port E data direction. Reset clears DDRE[1:0], configuring all port E pins as inputs. 1 = Corresponding port E pin configured as output 0 = Corresponding port E pin configured as input NOTE: Avoid glitches on port E pins by writing to the port E data register before changing data direction register E bits from 0 to 1. Figure 12-16 shows the port E I/O logic. READ DDRE ($000A) Freescale Semiconductor, Inc... WRITE DDRE ($000A) INTERNAL DATA BUS RESET WRITE PTE ($0008) PTEx PTEx DDREx READ PTE($0008) Figure 12-16. Port E I/O Circuit When bit DDREx is a 1, reading address $0008 reads the PTEx data latch. When bit DDREx is a 0, reading address $0008 reads the voltage level on the pin. The data latch can always be written, regardless of the state of its data direction bit. Table 12-5 summarizes the operation of the port E pins. Table 12-5. Port E Pin Functions DDRE Bit 0 1 PTE Bit X X I/O Pin Mode Input, Hi-Z Output Accesses to DDRE Read/Write DDRE[1:0] DDRE[1:0] Accesses to PTE Read Pin PTE[1:0] Write PTE[1:0](1) PTE[1:0] X = don't care Hi-Z = high impedance 1. Writing affects data register, but does not affect input. Data Sheet 148 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Input/Output (I/O) Ports (PORTS) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 13. Enhanced Serial Communications Interface (ESCI) Module 13.1 Introduction The enhanced serial communications interface (ESCI) module allows asynchronous communications with peripheral devices and other microcontroller units (MCU). Freescale Semiconductor, Inc... 13.2 Features Features include: * * * * * * * * Full-duplex operation Standard mark/space non-return-to-zero (NRZ) format Programmable baud rates Programmable 8-bit or 9-bit character length Separately enabled transmitter and receiver Separate receiver and transmitter central processor unit (CPU) interrupt requests Programmable transmitter output polarity Two receiver wakeup methods: - Idle line wakeup - address mark wakeup Interrupt-driven operation with eight interrupt flags: - Transmitter empty - Transmission complete - Receiver full - Idle receiver input - Receiver overrun - Noise error - Framing error - Parity error Receiver framing error detection Hardware parity checking 1/16 bit-time noise detection * * * * MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 149 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module INTERNAL BUS M68HC08 CPU CPU REGISTERS ARITHMETIC/LOGIC UNIT (ALU) SINGLE BREAKPOINT BREAK MODULE PORT A DDRA 5-BIT KEYBOARD INTERRUPT MODULE PTA6/SS PTA5/SPSCK PTA4/KBD4 PTA3/KBD3 PTA2/KBD2 PTA1/KBD1 2-CHANNEL TIMER INTERFACE MODULE A PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PORT B DDRB PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK PTC1/MOSI PTC0/MISO PTD1/TACH1 PTD0/TACH0 PTE1/RxD PTE0/TxD PORT C PORT E PORT D CONTROL AND STATUS REGISTERS 64 BYTES USER FLASH 15,872 BYTES USER RAM 512 BYTES Freescale Semiconductor, Inc... MONITOR ROM 310 BYTES FLASH PROGRAMMING (BURN-IN) ROM 1024 BYTES USER FLASH VECTOR SPACE 36 BYTES 2-CHANNEL TIMER INTERFACE MODULE B ENHANCED SERIAL COMMUNICATION INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE OSC2 OSC1 INTERNAL CLOCK GENERATOR MODULE SERIAL PERIPHERAL INTERFACE MODULE RST 24 INTERNAL SYSTEM INTEGRATION MODULE SINGLE EXTERNAL IRQ MODULE CONFIGURATION REGISTER MODULE PERIODIC WAKEUP TIMEBASE MODULE ARBITER MODULE PRESCALER MODULE IRQ VREFH VDDA VREFL VSSA VDD VSS DDRE DDRD DDRC 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE SECURITY MODULE POWER BEMF MODULE Figure 13-1. Block Diagram Highlighting ESCI Block and Pins Data Sheet 150 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module Pin Name Conventions 13.3 Pin Name Conventions The generic names of the ESCI input/output (I/O) pins are: * * RxD (receive data) TxD (transmit data) ESCI I/O lines are implemented by sharing parallel I/O port pins. The full name of an ESCI input or output reflects the name of the shared port pin. Table 13-1 shows the full names and the generic names of the ESCI I/O pins. The generic pin names appear in the text of this section. Freescale Semiconductor, Inc... Table 13-1. Pin Name Conventions Generic Pin Names Full Pin Names RxD PTE1/RxD TxD PTE0/TxD 13.4 Functional Description Figure 13-2 shows the structure of the ESCI module. The ESCI allows full-duplex, asynchronous, NRZ serial communication between the MCU and remote devices, including other MCUs. The transmitter and receiver of the ESCI operate independently, although they use the same baud rate generator. During normal operation, the CPU monitors the status of the ESCI, writes the data to be transmitted, and processes received data. The baud rate clock source for the ESCI can be selected via the configuration bit, ESCIBDSRC, of the CONFIG2 register ($001E). For reference, a summary of the ESCI module input/output registers is provided in Figure 13-3. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 151 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module INTERNAL BUS TRANSMITTER INTERRUPT CONTROL ESCI DATA REGISTER RECEIVE SHIFT REGISTER LINR SCTIE TCIE SCRIE ILIE TE RE RWU SBK SCTE SCRF IDLE ESCI DATA REGISTER RECEIVER INTERRUPT CONTROL ERROR INTERRUPT CONTROL SCI_TxD TRANSMIT SHIFT REGISTER TXINV R8 T8 BUS_CLK RxD ARBITERTxD RxD SL Freescale Semiconductor, Inc... ACLK bit in SCIACTL TC OR NF FE PE LOOPS LOOPS WAKEUP CONTROL RECEIVE CONTROL BKF RPF BAUD RATE GENERATOR FLAG CONTROL M WAKE ILTY /4 PRESCALER PEN PTY DATA SELECTION CONTROL ENSCI TRANSMIT CONTROL ORIE NEIE FEIE PEIE BUS CLOCK CGMXCLK Enhanced PRESCALER SL ESCIBDSRC FROM CONFIG2 ENSCI LINT / 16 SL=1 -> SCI_CLK = BUSCLK SL=0 -> SCI_CLK = CGMXCLK (4x BUSCLK) Figure 13-2. ESCI Module Block Diagram Data Sheet 152 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com SCI_CLK Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module Functional Description Addr. $0010 Register Name ESCI Control Register 1 Read: (SCC1) Write: See page 166. Reset: ESCI Control Register 2 Read: (SCC2) Write: See page 168. Reset: ESCI Control Register 3 Read: (SCC3) Write: See page 170. Reset: ESCI Status Register 1 Read: (SCS1) Write: See page 171. Reset: ESCI Status Register 2 Read: (SCS2) Write: See page 174. Reset: ESCI Data Register Read: (SCDR) Write: See page 175. Reset: ESCI Baud Rate Register Read: (SCBR) Write: See page 175. Reset: ESCI Prescaler Register Read: (SCPSC) Write: See page 177. Reset: ESCI Arbiter Control Read: Register (SCIACTL) Write: See page 180. Reset: ESCI Arbiter Data Read: Register (SCIADAT) Write: See page 181. Reset: Bit 7 LOOPS 0 SCTIE 0 R8 U SCTE 1 0 0 R7 T7 6 ENSCI 0 TCIE 0 T8 0 TC 1 0 0 R6 T6 5 TXINV 0 SCRIE 0 R 0 SCRF 0 0 0 R5 T5 4 M 0 ILIE 0 R 0 IDLE 0 0 0 R4 T4 3 WAKE 0 TE 0 ORIE 0 OR 0 0 0 R3 T3 2 ILTY 0 RE 0 NEIE 0 NF 0 0 0 R2 T2 1 PEN 0 RWU 0 FEIE 0 FE 0 BKF 0 R1 T1 Bit 0 PTY 0 SBK 0 PEIE 0 PE 0 RPF 0 R0 T0 $0011 $0012 Freescale Semiconductor, Inc... $0013 $0014 $0015 Unaffected by reset R 0 PDS2 0 AM1 0 ARD7 0 LINR 0 PDS1 0 ALOST 0 ARD6 0 = Unimplemented SCP1 0 PDS0 0 AM0 0 ARD5 0 SCP0 0 PSSB4 0 ACLK 0 ARD4 0 R R 0 PSSB3 0 AFIN 0 ARD3 0 = Reserved SCR2 0 PSSB2 0 ARUN 0 ARD2 0 SCR1 0 PSSB1 0 AROVFL 0 ARD1 0 U = Unaffected SCR0 0 PSSB0 0 ARD8 0 ARD0 0 $0016 $0017 $0018 $0019 Figure 13-3. ESCI I/O Register Summary MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 153 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module 13.4.1 Data Format The SCI uses the standard non-return-to-zero mark/space data format illustrated in Figure 13-4. PARITY OR DATA BIT BIT 7 STOP BIT PARITY OR DATA BIT BIT 6 BIT 7 BIT 8 START BIT 8-BIT DATA FORMAT (BIT M IN SCC1 CLEAR) BIT 0 BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 NEXT START BIT Freescale Semiconductor, Inc... START BIT 9-BIT DATA FORMAT (BIT M IN SCC1 SET) BIT 0 BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 NEXT START BIT STOP BIT Figure 13-4. SCI Data Formats 13.4.2 Transmitter Figure 13-5 shows the structure of the SCI transmitter and the registers are summarized in Figure 13-3. The baud rate clock source for the ESCI can be selected via the configuration bit, ESCIBDSRC. 13.4.2.1 Character Length The transmitter can accommodate either 8-bit or 9-bit data. The state of the M bit in ESCI control register 1 (SCC1) determines character length. When transmitting 9-bit data, bit T8 in ESCI control register 3 (SCC3) is the ninth bit (bit 8). 13.4.2.2 Character Transmission During an ESCI transmission, the transmit shift register shifts a character out to the TxD pin. The ESCI data register (SCDR) is the write-only buffer between the internal data bus and the transmit shift register. To initiate an ESCI transmission: 1. Enable the ESCI by writing a 1 to the enable ESCI bit (ENSCI) in ESCI control register 1 (SCC1). 2. Enable the transmitter by writing a 1 to the transmitter enable bit (TE) in ESCI control register 2 (SCC2). 3. Clear the ESCI transmitter empty bit (SCTE) by first reading ESCI status register 1 (SCS1) and then writing to the SCDR. For 9-bit data, also write the T8 bit in SCC3. 4. Repeat step 3 for each subsequent transmission. Data Sheet 154 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module Functional Description INTERNAL BUS /4 SCP1 SCP0 SCR1 SCR2 SCR0 TRANSMITTER CPU INTERRUPT REQUEST PRESCALER BAUD DIVIDER / 16 ESCI DATA REGISTER H 8 7 6 5 4 3 2 1 0 START L STOP 11-BIT TRANSMIT SHIFT REGISTER SCI_TxD Freescale Semiconductor, Inc... TXINV PRESCALER M PEN PTY PARITY GENERATION LOAD FROM SCDR BUS CLOCK SHIFT ENABLE PDS1 PDS0 PSSB4 PSSB3 PSSB2 PSSB1 PSSB0 T8 TRANSMITTER CONTROL LOGIC SCTE SCTE SCTIE TC TCIE PREAMBLE (ALL ONES) LOOPS SCTIE TC TCIE ENSCI TE LINT Figure 13-5. ESCI Transmitter At the start of a transmission, transmitter control logic automatically loads the transmit shift register with a preamble of 1s. After the preamble shifts out, control logic transfers the SCDR data into the transmit shift register. A 0 start bit automatically goes into the least significant bit (LSB) position of the transmit shift register. A 1 stop bit goes into the most significant bit (MSB) position. The ESCI transmitter empty bit, SCTE, in SCS1 becomes set when the SCDR transfers a byte to the transmit shift register. The SCTE bit indicates that the SCDR can accept new data from the internal data bus. If the ESCI transmit interrupt enable bit, SCTIE, in SCC2 is also set, the SCTE bit generates a transmitter CPU interrupt request. When the transmit shift register is not transmitting a character, the TxD pin goes to the idle condition, logic 1. If at any time software clears the ENSCI bit in ESCI control register 1 (SCC1), the transmitter and receiver relinquish control of the port E pins. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 155 For More Information On This Product, Go to: www.freescale.com BREAK (ALL ZEROS) SBK PDS2 MSB Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module 13.4.2.3 Break Characters Writing a 1 to the send break bit, SBK, in SCC2 loads the transmit shift register with a break character. For TXINV = 0 (output not inverted), a transmitted break character contains all 0s and has no start, stop, or parity bit. Break character length depends on the M bit in SCC1 and the LINR bits in SCBR. As long as SBK is at 1, transmitter logic continuously loads break characters into the transmit shift register. After software clears the SBK bit, the shift register finishes transmitting the last break character and then transmits at least one 1. The automatic 1 at the end of a break character guarantees the recognition of the start bit of the next character. When LINR is cleared in SCBR, the ESCI recognizes a break character when a start bit is followed by eight or nine 0 data bits and a 0 where the stop bit should be, resulting in a total of 10 or 11 consecutive 0 data bits. When LINR is set in SCBR, the ESCI recognizes a break character when a start bit is followed by 9 or 10 consecutive 0 data bits and a 0 where the stop bit should be, resulting in a total of 11 or 12 consecutive 0 data bits. Receiving a break character has these effects on ESCI registers: * * * * * * Sets the framing error bit (FE) in SCS1 Sets the ESCI receiver full bit (SCRF) in SCS1 Clears the ESCI data register (SCDR) Clears the R8 bit in SCC3 Sets the break flag bit (BKF) in SCS2 May set the overrun (OR), noise flag (NF), parity error (PE), or reception in progress flag (RPF) bits Freescale Semiconductor, Inc... 13.4.2.4 Idle Characters For TXINV = 0 (output not inverted), a transmitted idle character contains all 1s and has no start, stop, or parity bit. Idle character length depends on the M bit in SCC1. The preamble is a synchronizing idle character that begins every transmission. If the TE bit is cleared during a transmission, the TxD pin becomes idle after completion of the transmission in progress. Clearing and then setting the TE bit during a transmission queues an idle character to be sent after the character currently being transmitted. NOTE: When a break sequence is followed immediately by an idle character, this SCI design exhibits a condition in which the break character length is reduced by one half bit time. In this instance, the break sequence will consist of a valid start bit, eight or nine data bits (as defined by the M bit in SCC1) of 0 and one half data bit length of 0 in the stop bit position followed immediately by the idle character. To ensure a break character of the proper length is transmitted, always queue up a byte of data to be transmitted while the final break sequence is in progress. When queueing an idle character, return the TE bit to 1 before the stop bit of the current character shifts out to the TxD pin. Setting TE after the stop bit appears on Data Sheet 156 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module Functional Description TxD causes data previously written to the SCDR to be lost. A good time to toggle the TE bit for a queued idle character is when the SCTE bit becomes set and just before writing the next byte to the SCDR. 13.4.2.5 Inversion of Transmitted Output The transmit inversion bit (TXINV) in ESCI control register 1 (SCC1) reverses the polarity of transmitted data. All transmitted values including idle, break, start, and stop bits, are inverted when TXINV is at 1. See 13.8.1 ESCI Control Register 1. 13.4.2.6 Transmitter Interrupts Freescale Semiconductor, Inc... These conditions can generate CPU interrupt requests from the ESCI transmitter: * ESCI transmitter empty (SCTE) -- The SCTE bit in SCS1 indicates that the SCDR has transferred a character to the transmit shift register. SCTE can generate a transmitter CPU interrupt request. Setting the ESCI transmit interrupt enable bit, SCTIE, in SCC2 enables the SCTE bit to generate transmitter CPU interrupt requests. Transmission complete (TC) -- The TC bit in SCS1 indicates that the transmit shift register and the SCDR are empty and that no break or idle character has been generated. The transmission complete interrupt enable bit, TCIE, in SCC2 enables the TC bit to generate transmitter CPU interrupt requests. * 13.4.3 Receiver Figure 13-6 shows the structure of the ESCI receiver. The receiver I/O registers are summarized in Figure 13-3. 13.4.3.1 Character Length The receiver can accommodate either 8-bit or 9-bit data. The state of the M bit in ESCI control register 1 (SCC1) determines character length. When receiving 9-bit data, bit R8 in ESCI control register 3 (SCC3) is the ninth bit (bit 8). When receiving 8-bit data, bit R8 is a copy of the eighth bit (bit 7). 13.4.3.2 Character Reception During an ESCI reception, the receive shift register shifts characters in from the RxD pin. The ESCI data register (SCDR) is the read-only buffer between the internal data bus and the receive shift register. After a complete character shifts into the receive shift register, the data portion of the character transfers to the SCDR. The ESCI receiver full bit, SCRF, in ESCI status register 1 (SCS1) becomes set, indicating that the received byte can be read. If the ESCI receive interrupt enable bit, SCRIE, in SCC2 is also set, the SCRF bit generates a receiver CPU interrupt request. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 157 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module INTERNAL BUS LINR SCP1 SCP0 SCR1 SCR2 SCR0 START 0 L RWU PRESCALER BAUD DIVIDER ESCI DATA REGISTER STOP /4 PRESCALER / 16 DATA RECOVERY 11-BIT RECEIVE SHIFT REGISTER 8 7 6 5 4 3 2 1 RxD H ALL ONES Freescale Semiconductor, Inc... BUS CLOCK BKF PDS2 PDS1 PDS0 PSSB4 PSSB3 PSSB2 PSSB1 PSSB0 M WAKE ILTY PEN PTY RPF ALL ZEROS MSB SCRF WAKEUP LOGIC PARITY CHECKING IDLE ILIE SCRF SCRIE IDLE R8 ILIE CPU INTERRUPT REQUEST SCRIE OR ORIE ERROR CPU INTERRUPT REQUEST NF NEIE FE FEIE PE PEIE OR ORIE NF NEIE FE FEIE PE PEIE Figure 13-6. ESCI Receiver Block Diagram Data Sheet 158 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module Functional Description 13.4.3.3 Data Sampling The receiver samples the RxD pin at the RT clock rate. The RT clock is an internal signal with a frequency 16 times the baud rate. To adjust for baud rate mismatch, the RT clock is resynchronized at these times (see Figure 13-7): * * After every start bit After the receiver detects a data bit change from 1 to 0 (after the majority of data bit samples at RT8, RT9, and RT10 returns a valid 1 and the majority of the next RT8, RT9, and RT10 samples returns a valid 0) Freescale Semiconductor, Inc... To locate the start bit, data recovery logic does an asynchronous search for a 0 preceded by three 1s. When the falling edge of a possible start bit occurs, the RT clock begins to count to 16. RxD START BIT LSB SAMPLES START BIT QUALIFICATION START BIT DATA VERIFICATION SAMPLING RT CLOCK RT CLOCK STATE RT CLOCK RESET RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT1 RT2 RT3 RT4 RT5 RT6 RT7 RT8 RT9 RT10 RT11 RT12 RT13 RT14 RT15 RT16 RT1 RT2 RT3 RT4 Figure 13-7. Receiver Data Sampling To verify the start bit and to detect noise, data recovery logic takes samples at RT3, RT5, and RT7. Table 13-2 summarizes the results of the start bit verification samples. Table 13-2. Start Bit Verification RT3, RT5, and RT7 Samples 000 001 010 011 100 101 110 111 Start Bit Verification Yes Yes Yes No Yes No No No Noise Flag 0 1 1 0 1 0 0 0 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 159 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module If start bit verification is not successful, the RT clock is reset and a new search for a start bit begins. To determine the value of a data bit and to detect noise, recovery logic takes samples at RT8, RT9, and RT10. Table 13-3 summarizes the results of the data bit samples. Table 13-3. Data Bit Recovery RT8, RT9, and RT10 Samples 000 001 010 011 100 101 110 111 Data Bit Determination 0 0 0 1 0 1 1 1 Noise Flag 0 1 1 1 1 1 1 0 Freescale Semiconductor, Inc... NOTE: The RT8, RT9, and RT10 samples do not affect start bit verification. If any or all of the RT8, RT9, and RT10 start bit samples are 1s following a successful start bit verification, the noise flag (NF) is set and the receiver assumes that the bit is a start bit. To verify a stop bit and to detect noise, recovery logic takes samples at RT8, RT9, and RT10. Table 13-4 summarizes the results of the stop bit samples. Table 13-4. Stop Bit Recovery RT8, RT9, and RT10 Samples 000 001 010 011 100 101 110 111 Framing Error Flag 1 1 1 0 1 0 0 0 Noise Flag 0 1 1 1 1 1 1 0 13.4.3.4 Framing Errors If the data recovery logic does not detect a 1 where the stop bit should be in an incoming character, it sets the framing error bit, FE, in SCS1. A break character also sets the FE bit because a break character has no stop bit. The FE bit is set at the same time that the SCRF bit is set. Data Sheet 160 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module Functional Description 13.4.3.5 Baud Rate Tolerance A transmitting device may be operating at a baud rate below or above the receiver baud rate. Accumulated bit time misalignment can cause one of the three stop bit data samples to fall outside the actual stop bit. Then a noise error occurs. If more than one of the samples is outside the stop bit, a framing error occurs. In most applications, the baud rate tolerance is much more than the degree of misalignment that is likely to occur. As the receiver samples an incoming character, it resynchronizes the RT clock on any valid falling edge within the character. Resynchronization within characters corrects misalignments between transmitter bit times and receiver bit times. Freescale Semiconductor, Inc... Slow Data Tolerance Figure 13-8 shows how much a slow received character can be misaligned without causing a noise error or a framing error. The slow stop bit begins at RT8 instead of RT1 but arrives in time for the stop bit data samples at RT8, RT9, and RT10. MSB STOP RECEIVER RT CLOCK RT10 RT11 RT12 RT13 RT14 RT15 RT16 RT1 RT2 RT3 RT4 RT5 RT6 RT7 RT8 RT9 DATA SAMPLES Figure 13-8. Slow Data For an 8-bit character, data sampling of the stop bit takes the receiver 9 bit times x 16 RT cycles + 10 RT cycles = 154 RT cycles. With the misaligned character shown in Figure 13-8, the receiver counts 154 RT cycles at the point when the count of the transmitting device is 9 bit times x 16 RT cycles + 3 RT cycles = 147 RT cycles. The maximum percent difference between the receiver count and the transmitter count of a slow 8-bit character with no errors is: 154 - 147 x 100 = 4.54% ------------------------154 For a 9-bit character, data sampling of the stop bit takes the receiver 10 bit times x 16 RT cycles + 10 RT cycles = 170 RT cycles. With the misaligned character shown in Figure 13-8, the receiver counts 170 RT cycles at the point when the count of the transmitting device is 10 bit times x 16 RT cycles + 3 RT cycles = 163 RT cycles. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 161 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module The maximum percent difference between the receiver count and the transmitter count of a slow 9-bit character with no errors is: 170 - 163 x 100 = 4.12% ------------------------170 Fast Data Tolerance Figure 13-9 shows how much a fast received character can be misaligned without causing a noise error or a framing error. The fast stop bit ends at RT10 instead of RT16 but is still there for the stop bit data samples at RT8, RT9, and RT10. Freescale Semiconductor, Inc... STOP IDLE OR NEXT CHARACTER RECEIVER RT CLOCK RT10 RT11 RT12 RT13 RT14 RT15 RT16 RT1 RT2 RT3 RT4 RT5 RT6 RT7 RT8 RT9 DATA SAMPLES Figure 13-9. Fast Data For an 8-bit character, data sampling of the stop bit takes the receiver 9 bit times x 16 RT cycles + 10 RT cycles = 154 RT cycles. With the misaligned character shown in Figure 13-9, the receiver counts 154 RT cycles at the point when the count of the transmitting device is 10 bit times x 16 RT cycles = 160 RT cycles. The maximum percent difference between the receiver count and the transmitter count of a fast 8-bit character with no errors is 154 - 160 x 100 = 3.90%. ------------------------154 For a 9-bit character, data sampling of the stop bit takes the receiver 10 bit times x 16 RT cycles + 10 RT cycles = 170 RT cycles. With the misaligned character shown in Figure 13-9, the receiver counts 170 RT cycles at the point when the count of the transmitting device is 11 bit times x 16 RT cycles = 176 RT cycles. The maximum percent difference between the receiver count and the transmitter count of a fast 9-bit character with no errors is: 170 - 176 x 100 = 3.53%. ------------------------170 Data Sheet 162 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module Functional Description 13.4.3.6 Receiver Wakeup So that the MCU can ignore transmissions intended only for other receivers in multiple-receiver systems, the receiver can be put into a standby state. Setting the receiver wakeup bit, RWU, in SCC2 puts the receiver into a standby state during which receiver interrupts are disabled. Depending on the state of the WAKE bit in SCC1, either of two conditions on the RxD pin can bring the receiver out of the standby state: 1. Address mark -- An address mark is a 1 in the MSB position of a received character. When the WAKE bit is set, an address mark wakes the receiver from the standby state by clearing the RWU bit. The address mark also sets the ESCI receiver full bit, SCRF. Software can then compare the character containing the address mark to the user-defined address of the receiver. If they are the same, the receiver remains awake and processes the characters that follow. If they are not the same, software can set the RWU bit and put the receiver back into the standby state. 2. Idle input line condition -- When the WAKE bit is clear, an idle character on the RxD pin wakes the receiver from the standby state by clearing the RWU bit. The idle character that wakes the receiver does not set the receiver idle bit, IDLE, or the ESCI receiver full bit, SCRF. The idle line type bit, ILTY, determines whether the receiver begins counting 1s as idle character bits after the start bit or after the stop bit. NOTE: With the WAKE bit clear, setting the RWU bit after the RxD pin has been idle will cause the receiver to wake up. Freescale Semiconductor, Inc... 13.4.3.7 Receiver Interrupts These sources can generate CPU interrupt requests from the ESCI receiver: * ESCI receiver full (SCRF) -- The SCRF bit in SCS1 indicates that the receive shift register has transferred a character to the SCDR. SCRF can generate a receiver CPU interrupt request. Setting the ESCI receive interrupt enable bit, SCRIE, in SCC2 enables the SCRF bit to generate receiver CPU interrupts. Idle input (IDLE) -- The IDLE bit in SCS1 indicates that 10 or 11 consecutive 1s shifted in from the RxD pin. The idle line interrupt enable bit, ILIE, in SCC2 enables the IDLE bit to generate CPU interrupt requests. * MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 163 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module 13.4.3.8 Error Interrupts These receiver error flags in SCS1 can generate CPU interrupt requests: * Receiver overrun (OR) -- The OR bit indicates that the receive shift register shifted in a new character before the previous character was read from the SCDR. The previous character remains in the SCDR, and the new character is lost. The overrun interrupt enable bit, ORIE, in SCC3 enables OR to generate ESCI error CPU interrupt requests. Noise flag (NF) -- The NF bit is set when the ESCI detects noise on incoming data or break characters, including start, data, and stop bits. The noise error interrupt enable bit, NEIE, in SCC3 enables NF to generate ESCI error CPU interrupt requests. Framing error (FE) -- The FE bit in SCS1 is set when a 0 occurs where the receiver expects a stop bit. The framing error interrupt enable bit, FEIE, in SCC3 enables FE to generate ESCI error CPU interrupt requests. Parity error (PE) -- The PE bit in SCS1 is set when the ESCI detects a parity error in incoming data. The parity error interrupt enable bit, PEIE, in SCC3 enables PE to generate ESCI error CPU interrupt requests. * Freescale Semiconductor, Inc... * * 13.5 Low-Power Modes The WAIT and STOP instructions put the MCU in low power-consumption standby modes. 13.5.1 Wait Mode The ESCI module remains active in wait mode. Any enabled CPU interrupt request from the ESCI module can bring the MCU out of wait mode. If ESCI module functions are not required during wait mode, reduce power consumption by disabling the module before executing the WAIT instruction. 13.5.2 Stop Mode The ESCI module is inactive in stop mode. The STOP instruction does not affect ESCI register states. ESCI module operation resumes after the MCU exits stop mode. Because the internal clock is inactive during stop mode, entering stop mode during an ESCI transmission or reception results in invalid data. 13.6 ESCI During Break Module Interrupts The BCFE bit in the break flag control register (SBFCR) enables software to clear status bits during the break state. See 19.2 Break Module (BRK). Data Sheet 164 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module I/O Signals To allow software to clear status bits during a break interrupt, write a 1 to the BCFE bit. If a status bit is cleared during the break state, it remains cleared when the MCU exits the break state. To protect status bits during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default state), software can read and write I/O registers during the break state without affecting status bits. Some status bits have a two-step read/write clearing procedure. If software does the first step on such a bit before the break, the bit cannot change during the break state as long as BCFE is at 0. After the break, doing the second step clears the status bit. Freescale Semiconductor, Inc... 13.7 I/O Signals Port E shares two of its pins with the ESCI module. The two ESCI I/O pins are: * * PTE0/TxD -- transmit data PTE1/RxD -- receive data 13.7.1 PTE0/TxD (Transmit Data) The PTE0/TxD pin is the serial data output from the ESCI transmitter. The ESCI shares the PTE0/TxD pin with port E. When the ESCI is enabled, the PTE0/TxD pin is an output regardless of the state of the DDRE0 bit in data direction register E (DDRE). 13.7.2 PTE1/RxD (Receive Data) The PTE1/RxD pin is the serial data input to the ESCI receiver. The ESCI shares the PTE1/RxD pin with port E. When the ESCI is enabled, the PTE1/RxD pin is an input regardless of the state of the DDRE1 bit in data direction register E (DDRE). 13.8 I/O Registers These I/O registers control and monitor ESCI operation: * * * * * * * * * * ESCI control register 1, SCC1 ESCI control register 2, SCC2 ESCI control register 3, SCC3 ESCI status register 1, SCS1 ESCI status register 2, SCS2 ESCI data register, SCDR ESCI baud rate register, SCBR ESCI prescaler register, SCPSC ESCI arbiter control register, SCIACTL ESCI arbiter data register, SCIADAT Data Sheet 165 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module 13.8.1 ESCI Control Register 1 ESCI control register 1 (SCC1): * * * * * * * * Enables loop mode operation Enables the ESCI Controls output polarity Controls character length Controls ESCI wakeup method Controls idle character detection Enables parity function Controls parity type Freescale Semiconductor, Inc... Address: $0010 Bit 7 Read: Write: Reset: LOOPS 0 6 ENSCI 0 5 TXINV 0 4 M 0 3 WAKE 0 2 ILTY 0 1 PEN 0 Bit 0 PTY 0 Figure 13-10. ESCI Control Register 1 (SCC1) LOOPS -- Loop Mode Select Bit This read/write bit enables loop mode operation. In loop mode the RxD pin is disconnected from the ESCI, and the transmitter output goes into the receiver input. Both the transmitter and the receiver must be enabled to use loop mode. Reset clears the LOOPS bit. 1 = Loop mode enabled 0 = Normal operation enabled ENSCI -- Enable ESCI Bit This read/write bit enables the ESCI and the ESCI baud rate generator. Clearing ENSCI sets the SCTE and TC bits in ESCI status register 1 and disables transmitter interrupts. Reset clears the ENSCI bit. 1 = ESCI enabled 0 = ESCI disabled TXINV -- Transmit Inversion Bit This read/write bit reverses the polarity of transmitted data. Reset clears the TXINV bit. 1 = Transmitter output inverted 0 = Transmitter output not inverted NOTE: Setting the TXINV bit inverts all transmitted values including idle, break, start, and stop bits. Data Sheet 166 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module I/O Registers M -- Mode (Character Length) Bit This read/write bit determines whether ESCI characters are eight or nine bits long (See Table 13-5).The ninth bit can serve as a receiver wakeup signal or as a parity bit. Reset clears the M bit. 1 = 9-bit ESCI characters 0 = 8-bit ESCI characters Table 13-5. Character Format Selection Control Bits M 0 1 0 0 1 1 PEN:PTY 0X 0X 10 11 10 11 Start Bits 1 1 1 1 1 1 Data Bits 8 9 7 7 8 8 Character Format Parity None None Even Odd Even Odd Stop Bits 1 1 1 1 1 1 Character Length 10 bits 11 bits 10 bits 10 bits 11 bits 11 bits Freescale Semiconductor, Inc... WAKE -- Wakeup Condition Bit This read/write bit determines which condition wakes up the ESCI: a 1 (address mark) in the MSB position of a received character or an idle condition on the RxD pin. Reset clears the WAKE bit. 1 = Address mark wakeup 0 = Idle line wakeup ILTY -- Idle Line Type Bit This read/write bit determines when the ESCI starts counting 1s as idle character bits. The counting begins either after the start bit or after the stop bit. If the count begins after the start bit, then a string of 1s preceding the stop bit may cause false recognition of an idle character. Beginning the count after the stop bit avoids false idle character recognition, but requires properly synchronized transmissions. Reset clears the ILTY bit. 1 = Idle character bit count begins after stop bit 0 = Idle character bit count begins after start bit PEN -- Parity Enable Bit This read/write bit enables the ESCI parity function (see Table 13-5). When enabled, the parity function inserts a parity bit in the MSB position (see Table 13-3). Reset clears the PEN bit. 1 = Parity function enabled 0 = Parity function disabled PTY -- Parity Bit This read/write bit determines whether the ESCI generates and checks for odd parity or even parity (see Table 13-5). Reset clears the PTY bit. 1 = Odd parity 0 = Even parity NOTE: Changing the PTY bit in the middle of a transmission or reception can generate a parity error. Data Sheet 167 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module 13.8.2 ESCI Control Register 2 ESCI control register 2 (SCC2): * Enables these CPU interrupt requests: - SCTE bit to generate transmitter CPU interrupt requests - TC bit to generate transmitter CPU interrupt requests - SCRF bit to generate receiver CPU interrupt requests - IDLE bit to generate receiver CPU interrupt requests Enables the transmitter Enables the receiver Enables ESCI wakeup Transmits ESCI break characters * * Freescale Semiconductor, Inc... * * Address: $0011 Bit 7 Read: Write: Reset: SCTIE 0 6 TCIE 0 5 SCRIE 0 4 ILIE 0 3 TE 0 2 RE 0 1 RWU 0 Bit 0 SBK 0 Figure 13-11. ESCI Control Register 2 (SCC2) SCTIE -- ESCI Transmit Interrupt Enable Bit This read/write bit enables the SCTE bit to generate ESCI transmitter CPU interrupt requests. Setting the SCTIE bit in SCC2 enables the SCTE bit to generate CPU interrupt requests. Reset clears the SCTIE bit. 1 = SCTE enabled to generate CPU interrupt 0 = SCTE not enabled to generate CPU interrupt TCIE -- Transmission Complete Interrupt Enable Bit This read/write bit enables the TC bit to generate ESCI transmitter CPU interrupt requests. Reset clears the TCIE bit. 1 = TC enabled to generate CPU interrupt requests 0 = TC not enabled to generate CPU interrupt requests SCRIE -- ESCI Receive Interrupt Enable Bit This read/write bit enables the SCRF bit to generate ESCI receiver CPU interrupt requests. Setting the SCRIE bit in SCC2 enables the SCRF bit to generate CPU interrupt requests. Reset clears the SCRIE bit. 1 = SCRF enabled to generate CPU interrupt 0 = SCRF not enabled to generate CPU interrupt ILIE -- Idle Line Interrupt Enable Bit This read/write bit enables the IDLE bit to generate ESCI receiver CPU interrupt requests. Reset clears the ILIE bit. 1 = IDLE enabled to generate CPU interrupt requests 0 = IDLE not enabled to generate CPU interrupt requests Data Sheet 168 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module I/O Registers TE -- Transmitter Enable Bit Setting this read/write bit begins the transmission by sending a preamble of 10 or 11 consecutive 1s from the transmit shift register to the TxD pin. If software clears the TE bit, the transmitter completes any transmission in progress before the TxD returns to the idle condition (1). Clearing and then setting TE during a transmission queues an idle character to be sent after the character currently being transmitted. Reset clears the TE bit. 1 = Transmitter enabled 0 = Transmitter disabled NOTE: Writing to the TE bit is not allowed when the enable ESCI bit (ENSCI) is clear. ENSCI is in ESCI control register 1. RE -- Receiver Enable Bit Setting this read/write bit enables the receiver. Clearing the RE bit disables the receiver but does not affect receiver interrupt flag bits. Reset clears the RE bit. 1 = Receiver enabled 0 = Receiver disabled NOTE: Writing to the RE bit is not allowed when the enable ESCI bit (ENSCI) is clear. ENSCI is in ESCI control register 1. RWU -- Receiver Wakeup Bit This read/write bit puts the receiver in a standby state during which receiver interrupts are disabled. The WAKE bit in SCC1 determines whether an idle input or an address mark brings the receiver out of the standby state and clears the RWU bit. Reset clears the RWU bit. 1 = Standby state 0 = Normal operation SBK -- Send Break Bit Setting and then clearing this read/write bit transmits a break character followed by a 1. The 1 after the break character guarantees recognition of a valid start bit. If SBK remains set, the transmitter continuously transmits break characters with no 1s between them. Reset clears the SBK bit. 1 = Transmit break characters 0 = No break characters being transmitted NOTE: Do not toggle the SBK bit immediately after setting the SCTE bit. Toggling SBK before the preamble begins causes the ESCI to send a break character instead of a preamble. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 169 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module 13.8.3 ESCI Control Register 3 ESCI control register 3 (SCC3): * * Stores the ninth ESCI data bit received and the ninth ESCI data bit to be transmitted. Enables these interrupts: - Receiver overrun - Noise error - Framing error - Parity error $0012 Bit 7 Read: Write: Reset: U R8 6 T8 0 5 R 0 4 R 0 R 3 ORIE 0 = Reserved 2 NEIE 0 1 FEIE 0 U = Unaffected Bit 0 PEIE 0 Freescale Semiconductor, Inc... Address: = Unimplemented Figure 13-12. ESCI Control Register 3 (SCC3) R8 -- Received Bit 8 When the ESCI is receiving 9-bit characters, R8 is the read-only ninth bit (bit 8) of the received character. R8 is received at the same time that the SCDR receives the other 8 bits. When the ESCI is receiving 8-bit characters, R8 is a copy of the eighth bit (bit 7). Reset has no effect on the R8 bit. T8 -- Transmitted Bit 8 When the ESCI is transmitting 9-bit characters, T8 is the read/write ninth bit (bit 8) of the transmitted character. T8 is loaded into the transmit shift register at the same time that the SCDR is loaded into the transmit shift register. Reset clears the T8 bit. ORIE -- Receiver Overrun Interrupt Enable Bit This read/write bit enables ESCI error CPU interrupt requests generated by the receiver overrun bit, OR. Reset clears ORIE. 1 = ESCI error CPU interrupt requests from OR bit enabled 0 = ESCI error CPU interrupt requests from OR bit disabled NEIE -- Receiver Noise Error Interrupt Enable Bit This read/write bit enables ESCI error CPU interrupt requests generated by the noise error bit, NE. Reset clears NEIE. 1 = ESCI error CPU interrupt requests from NE bit enabled 0 = ESCI error CPU interrupt requests from NE bit disabled Data Sheet 170 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module I/O Registers FEIE -- Receiver Framing Error Interrupt Enable Bit This read/write bit enables ESCI error CPU interrupt requests generated by the framing error bit, FE. Reset clears FEIE. 1 = ESCI error CPU interrupt requests from FE bit enabled 0 = ESCI error CPU interrupt requests from FE bit disabled PEIE -- Receiver Parity Error Interrupt Enable Bit This read/write bit enables ESCI receiver CPU interrupt requests generated by the parity error bit, PE. Reset clears PEIE. 1 = ESCI error CPU interrupt requests from PE bit enabled 0 = ESCI error CPU interrupt requests from PE bit disabled Freescale Semiconductor, Inc... 13.8.4 ESCI Status Register 1 ESCI status register 1 (SCS1) contains flags to signal these conditions: * * * * * * * * Transfer of SCDR data to transmit shift register complete Transmission complete Transfer of receive shift register data to SCDR complete Receiver input idle Receiver overrun Noisy data Framing error Parity error $0013 Bit 7 Read: Write: Reset: 1 1 0 0 0 0 0 0 = Unimplemented SCTE 6 TC 5 SCRF 4 IDLE 3 OR 2 NF 1 FE Bit 0 PE Address: Figure 13-13. ESCI Status Register 1 (SCS1) SCTE -- ESCI Transmitter Empty Bit This clearable, read-only bit is set when the SCDR transfers a character to the transmit shift register. SCTE can generate an ESCI transmitter CPU interrupt request. When the SCTIE bit in SCC2 is set, SCTE generates an ESCI transmitter CPU interrupt request. In normal operation, clear the SCTE bit by reading SCS1 with SCTE set and then writing to SCDR. Reset sets the SCTE bit. 1 = SCDR data transferred to transmit shift register 0 = SCDR data not transferred to transmit shift register MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 171 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module TC -- Transmission Complete Bit This read-only bit is set when the SCTE bit is set, and no data, preamble, or break character is being transmitted. TC generates an ESCI transmitter CPU interrupt request if the TCIE bit in SCC2 is also set. TC is cleared automatically when data, preamble, or break is queued and ready to be sent. There may be up to 1.5 transmitter clocks of latency between queueing data, preamble, and break and the transmission actually starting. Reset sets the TC bit. 1 = No transmission in progress 0 = Transmission in progress SCRF -- ESCI Receiver Full Bit This clearable, read-only bit is set when the data in the receive shift register transfers to the ESCI data register. SCRF can generate an ESCI receiver CPU interrupt request. When the SCRIE bit in SCC2 is set the SCRF generates a CPU interrupt request. In normal operation, clear the SCRF bit by reading SCS1 with SCRF set and then reading the SCDR. Reset clears SCRF. 1 = Received data available in SCDR 0 = Data not available in SCDR IDLE -- Receiver Idle Bit This clearable, read-only bit is set when 10 or 11 consecutive 1s appear on the receiver input. IDLE generates an ESCI error CPU interrupt request if the ILIE bit in SCC2 is also set. Clear the IDLE bit by reading SCS1 with IDLE set and then reading the SCDR. After the receiver is enabled, it must receive a valid character that sets the SCRF bit before an idle condition can set the IDLE bit. Also, after the IDLE bit has been cleared, a valid character must again set the SCRF bit before an idle condition can set the IDLE bit. Reset clears the IDLE bit. 1 = Receiver input idle 0 = Receiver input active (or idle since the IDLE bit was cleared) OR -- Receiver Overrun Bit This clearable, read-only bit is set when software fails to read the SCDR before the receive shift register receives the next character. The OR bit generates an ESCI error CPU interrupt request if the ORIE bit in SCC3 is also set. The data in the shift register is lost, but the data already in the SCDR is not affected. Clear the OR bit by reading SCS1 with OR set and then reading the SCDR. Reset clears the OR bit. 1 = Receive shift register full and SCRF = 1 0 = No receiver overrun Software latency may allow an overrun to occur between reads of SCS1 and SCDR in the flag-clearing sequence. Figure 13-14 shows the normal flag-clearing sequence and an example of an overrun caused by a delayed flag-clearing sequence. The delayed read of SCDR does not clear the OR bit because OR was not set when SCS1 was read. Byte 2 caused the overrun and is lost. The next flag-clearing sequence reads byte 3 in the SCDR instead of byte 2. Freescale Semiconductor, Inc... Data Sheet 172 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module I/O Registers NORMAL FLAG CLEARING SEQUENCE SCRF = 1 SCRF = 0 SCRF = 1 SCRF = 0 SCRF = 1 SCRF = 0 BYTE 4 READ SCS1 SCRF = 1 OR = 0 READ SCDR BYTE 3 BYTE 4 READ SCS1 SCRF = 1 OR = 1 READ SCDR BYTE 3 SCRF = 0 OR = 0 BYTE 1 READ SCS1 SCRF = 1 OR = 0 READ SCDR BYTE 1 BYTE 2 READ SCS1 SCRF = 1 OR = 0 READ SCDR BYTE 2 BYTE 3 Freescale Semiconductor, Inc... DELAYED FLAG CLEARING SEQUENCE SCRF = 1 OR = 1 SCRF = 1 SCRF = 0 OR = 1 SCRF = 1 OR = 1 BYTE 3 BYTE 1 BYTE 2 READ SCS1 SCRF = 1 OR = 0 READ SCDR BYTE 1 Figure 13-14. Flag Clearing Sequence In applications that are subject to software latency or in which it is important to know which byte is lost due to an overrun, the flag-clearing routine can check the OR bit in a second read of SCS1 after reading the data register. NF -- Receiver Noise Flag Bit This clearable, read-only bit is set when the ESCI detects noise on the RxD pin. NF generates an NF CPU interrupt request if the NEIE bit in SCC3 is also set. Clear the NF bit by reading SCS1 and then reading the SCDR. Reset clears the NF bit. 1 = Noise detected 0 = No noise detected FE -- Receiver Framing Error Bit This clearable, read-only bit is set when a 0 is accepted as the stop bit. FE generates an ESCI error CPU interrupt request if the FEIE bit in SCC3 also is set. Clear the FE bit by reading SCS1 with FE set and then reading the SCDR. Reset clears the FE bit. 1 = Framing error detected 0 = No framing error detected PE -- Receiver Parity Error Bit This clearable, read-only bit is set when the ESCI detects a parity error in incoming data. PE generates a PE CPU interrupt request if the PEIE bit in SCC3 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 173 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module is also set. Clear the PE bit by reading SCS1 with PE set and then reading the SCDR. Reset clears the PE bit. 1 = Parity error detected 0 = No parity error detected 13.8.5 ESCI Status Register 2 ESCI status register 2 (SCS2) contains flags to signal these conditions: * * Break character detected Incoming data $0014 Bit 7 Read: Write: Reset: 0 0 0 0 0 0 0 0 = Unimplemented 0 6 0 5 0 4 0 3 0 2 0 1 BKF Bit 0 RPF Freescale Semiconductor, Inc... Address: Figure 13-15. ESCI Status Register 2 (SCS2) BKF -- Break Flag Bit This clearable, read-only bit is set when the ESCI detects a break character on the RxD pin. In SCS1, the FE and SCRF bits are also set. In 9-bit character transmissions, the R8 bit in SCC3 is cleared. BKF does not generate a CPU interrupt request. Clear BKF by reading SCS2 with BKF set and then reading the SCDR. Once cleared, BKF can become set again only after 1s again appear on the RxD pin followed by another break character. Reset clears the BKF bit. 1 = Break character detected 0 = No break character detected RPF -- Reception in Progress Flag Bit This read-only bit is set when the receiver detects a 0 during the RT1 time period of the start bit search. RPF does not generate an interrupt request. RPF is reset after the receiver detects false start bits (usually from noise or a baud rate mismatch), or when the receiver detects an idle character. Polling RPF before disabling the ESCI module or entering stop mode can show whether a reception is in progress. 1 = Reception in progress 0 = No reception in progress Data Sheet 174 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module I/O Registers 13.8.6 ESCI Data Register The ESCI data register (SCDR) is the buffer between the internal data bus and the receive and transmit shift registers. Reset has no effect on data in the ESCI data register. Address: Read: Write: Reset: $0015 Bit 7 R7 T7 6 R6 T6 5 R5 T5 4 R4 T4 3 R3 T3 2 R2 T2 1 R1 T1 Bit 0 R0 T0 Unaffected by Reset Freescale Semiconductor, Inc... Figure 13-16. ESCI Data Register (SCDR) R7/T7:R0/T0 -- Receive/Transmit Data Bits Reading address $0015 accesses the read-only received data bits, R7:R0. Writing to address $0015 writes the data to be transmitted, T7:T0. Reset has no effect on the ESCI data register. NOTE: Do not use read-modify-write instructions on the ESCI data register. 13.8.7 ESCI Baud Rate Register The ESCI baud rate register (SCBR) together with the ESCI prescaler register selects the baud rate for both the receiver and the transmitter. NOTE: There are two prescalers available to adjust the baud rate. One in the ESCI baud rate register and one in the ESCI prescaler register. Address: Read: Write: Reset: $0016 Bit 7 R 0 6 LINR 0 5 SCP1 0 4 SCP0 0 R 3 R 0 = Reserved 2 SCR2 0 1 SCR1 0 Bit 0 SCR0 0 = Unimplemented Figure 13-17. ESCI Baud Rate Register (SCBR) LINR -- LIN Receiver Bits This read/write bit selects the enhanced ESCI features for slave nodes in the local interconnect network (LIN) protocol as shown in Table 13-6. Reset clears LINR. Table 13-6. ESCI LIN Control Bits LINR 0 1 1 M X 0 1 Functionality Normal ESCI functionality 11-bit break detect enabled for LIN receiver 12-bit break detect enabled for LIN receiver MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 175 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module In LIN (version 1.2) systems, the master node transmits a break character which will appear as 11.05-14.95 dominant bits to the slave node. A data character of 0x00 sent from the master might appear as 7.65-10.35 dominant bit times. This is due to the oscillator tolerance requirement that the slave node must be within 15% of the master node's oscillator. Since a slave node cannot know if it is running faster or slower than the master node (prior to synchronization), the LINR bit allows the slave node to differentiate between a 0x00 character of 10.35 bits and a break character of 11.05 bits. The break symbol length must be verified in software in any case, but the LINR bit serves as a filter, preventing false detections of break characters that are really 0x00 data characters. Freescale Semiconductor, Inc... SCP1 and SCP0 -- ESCI Baud Rate Register Prescaler Bits These read/write bits select the baud rate register prescaler divisor as shown in Table 13-7. Reset clears SCP1 and SCP0. Table 13-7. ESCI Baud Rate Prescaling SCP[1:0] 00 01 10 11 Baud Rate Register Prescaler Divisor (BPD) 1 3 4 13 SCR2-SCR0 -- ESCI Baud Rate Select Bits These read/write bits select the ESCI baud rate divisor as shown in Table 13-8. Reset clears SCR2-SCR0. Table 13-8. ESCI Baud Rate Selection SCR[2:1:0] 000 001 010 011 100 101 110 111 Baud Rate Divisor (BD) 1 2 4 8 16 32 64 128 13.8.8 ESCI Prescaler Register The ESCI prescaler register (SCPSC) together with the ESCI baud rate register selects the baud rate for both the receiver and the transmitter. NOTE: There are two prescalers available to adjust the baud rate. One in the ESCI baud rate register and one in the ESCI prescaler register. Data Sheet 176 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module I/O Registers Address: Read: Write: Reset: $0017 Bit 7 PDS2 0 6 PDS1 0 5 PDS0 0 4 PSSB4 0 3 PSSB3 0 2 PSSB2 0 1 PSSB1 0 Bit 0 PSSB0 0 Figure 13-18. ESCI Prescaler Register (SCPSC) PDS2-PDS0 -- Prescaler Divisor Select Bits These read/write bits select the prescaler divisor as shown in Table 13-9. Reset clears PDS2-PDS0. Freescale Semiconductor, Inc... NOTE: The setting of `000' will bypass not only this prescaler but also the Prescaler Divisor Fine Adjust (PDFA). It is not recommended to bypass the prescaler while ENSCI is set, because the switching is not glitch free. Table 13-9. ESCI Prescaler Division Ratio PDS[2:1:0] 000 001 010 011 100 101 110 111 Prescaler Divisor (PD) Bypass this prescaler 2 3 4 5 6 7 8 PSSB4-PSSB0 -- Clock Insertion Select Bits These read/write bits select the number of clocks inserted in each 32 output cycle frame to achieve more timing resolution on the average prescaler frequency as shown in Table 13-10. Reset clears PSSB4-PSSB0. Use the following formula to calculate the ESCI baud rate: Baud rate = Frequency of the SCI clock source 64 x BPD x BD x (PD + PDFA) where: Frequency of the SCI clock source = fBus or CGMXCLK (selected by ESCIBDSRC in the CONFIG2 register) BPD = Baud rate register prescaler divisor BD = Baud rate divisor PD = Prescaler divisor PDFA = Prescaler divisor fine adjust Table 13-11 shows the ESCI baud rates that can be generated with a 4.9152-MHz clock frequency. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 177 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module Table 13-10. ESCI Prescaler Divisor Fine Adjust PSSB[4:3:2:1:0] 00000 00001 00010 00011 00100 00101 00110 Prescaler Divisor Fine Adjust (PDFA) 0/32 = 0 1/32 = 0.03125 2/32 = 0.0625 3/32 = 0.09375 4/32 = 0.125 5/32 = 0.15625 6/32 = 0.1875 7/32 = 0.21875 8/32 = 0.25 9/32 = 0.28125 10/32 = 0.3125 11/32 = 0.34375 12/32 = 0.375 13/32 = 0.40625 14/32 = 0.4375 15/32 = 0.46875 16/32 = 0.5 17/32 = 0.53125 18/32 = 0.5625 19/32 = 0.59375 20/32 = 0.625 21/32 = 0.65625 22/32 = 0.6875 23/32 = 0.71875 24/32 = 0.75 25/32 = 0.78125 26/32 = 0.8125 27/32 = 0.84375 28/32 = 0.875 29/32 = 0.90625 30/32 = 0.9375 31/32 = 0.96875 Freescale Semiconductor, Inc... 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 10001 10010 10011 10100 10101 10110 10111 11000 11001 11010 11011 11100 11101 11110 11111 Data Sheet 178 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module I/O Registers Table 13-11. ESCI Baud Rate Selection Examples PDS[2:1:0] 000 111 111 111 111 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 000 PSSB[4:3:2:1:0] XXXXX 00000 00001 00010 11111 XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX XXXXX SCP[1:0] 00 00 00 00 00 00 00 00 00 00 00 00 01 01 01 01 01 01 01 01 10 10 10 10 10 10 10 10 11 11 11 11 11 11 11 11 Prescaler Divisor (BPD) 1 1 1 1 1 1 1 1 1 1 1 1 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4 13 13 13 13 13 13 13 13 SCR[2:1:0] 000 000 000 000 000 001 010 011 100 101 110 111 000 001 010 011 100 101 110 111 000 001 010 011 100 101 110 111 000 001 010 011 100 101 110 111 Baud Rate Divisor (BD) 1 1 1 1 1 2 4 8 16 32 64 128 1 2 4 8 16 32 64 128 1 2 4 8 16 32 64 128 1 2 4 8 16 32 64 128 Baud Rate (ESCI Clock = 4.9152 MHz) 76,800 9600 9562.65 9525.58 8563.07 38,400 19,200 9600 4800 2400 1200 600 25,600 12,800 6400 3200 1600 800 400 200 19,200 9600 4800 2400 1200 600 300 150 5908 2954 1477 739 369 185 92 46 Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 179 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module 13.9 ESCI Arbiter The ESCI module comprises an arbiter module designed to support software for communication tasks as bus arbitration, baud rate recovery and break time detection. The arbiter module consists of an 9-bit counter with 1-bit overflow and control logic. The CPU can control operation mode via the ESCI arbiter control register (SCIACTL). 13.9.1 ESCI Arbiter Control Register Address: $0018 Bit 7 Read: Write: Reset: AM1 0 6 ALOST 0 5 AM0 0 4 ACLK 0 3 AFIN 0 2 ARUN 0 1 AROVFL 0 Bit 0 ARD8 0 Freescale Semiconductor, Inc... = Unimplemented Figure 13-19. ESCI Arbiter Control Register (SCIACTL) AM1 and AM0 -- Arbiter Mode Select Bits As shown in Table 13-12, these read/write bits select the mode of the arbiter module. Reset clears AM1 and AM0. Table 13-12. ESCI Arbiter Selectable Modes AM[1:0] 00 01 10 11 ESCI Arbiter Mode Idle / counter reset Bit time measurement Bus arbitration Reserved / do not use ALOST -- Arbitration Lost Flag This read-only bit indicates loss of arbitration. Clear ALOST by writing a 0 to AM1. Reset clears ALOST. ACLK -- Arbiter Counter Clock Select Bit This read/write bit selects the arbiter counter clock source. Reset clears ACLK. 1 = Arbiter counter is clocked with one half of the ESCI input clock generated by the ESCI prescaler. 0 = Arbiter counter is clocked with the bus clock divided by four NOTE: For ACLK=1, the Arbiter input clock is driven from the ESCI prescaler. The prescaler can be clocked by either the bus clock or CGMXCLK depending on the state of the ESCIBDSRC bit in CONFIG2. Data Sheet 180 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module ESCI Arbiter AFIN-- Arbiter Bit Time Measurement Finish Flag This read-only bit indicates bit time measurement has finished. Clear AFIN by writing any value to SCIACTL. Reset clears AFIN. 1 = Bit time measurement has finished 0 = Bit time measurement not yet finished ARUN-- Arbiter Counter Running Flag This read-only bit indicates the arbiter counter is running. Reset clears ARUN. 1 = Arbiter counter running 0 = Arbiter counter stopped AROVFL-- Arbiter Counter Overflow Bit This read-only bit indicates an arbiter counter overflow. Clear AROVFL by writing any value to SCIACTL. Writing 0s to AM1 and AM0 resets the counter keeps it in this idle state. Reset clears AROVFL. 1 = Arbiter counter overflow has occurred 0 = No arbiter counter overflow has occurred ARD8-- Arbiter Counter MSB This read-only bit is the MSB of the 9-bit arbiter counter. Clear ARD8 by writing any value to SCIACTL. Reset clears ARD8. 13.9.2 ESCI Arbiter Data Register Address: $0019 Bit 7 Read: Write: Reset: 0 0 0 0 0 0 0 0 = Unimplemented ARD7 6 ARD6 5 ARD5 4 ARD4 3 ARD3 2 ARD2 1 ARD1 Bit 0 ARD0 Freescale Semiconductor, Inc... Figure 13-20. ESCI Arbiter Data Register (SCIADAT) ARD7-ARD0 -- Arbiter Least Significant Counter Bits These read-only bits are the eight LSBs of the 9-bit arbiter counter. Clear ARD7-ARD0 by writing any value to SCIACTL. Writing 0s to AM1 and AM0 permanently resets the counter and keeps it in this idle state. Reset clears ARD7-ARD0. 13.9.3 Bit Time Measurement Two bit time measurement modes, described here, are available according to the state of ACLK. 1. ACLK = 0 -- The counter is clocked with one quarter of the bus clock. The counter is started when a falling edge on the RxD pin is detected. The counter will be stopped on the next falling edge. ARUN is set while the counter is running, AFIN is set on the second falling edge on RxD (for instance, the counter is stopped). This mode is used to recover the received baud rate. See Figure 13-21. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 181 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module 2. ACLK = 1 -- The counter is clocked with one half of the ESCI input clock generated by the ESCI prescaler. The counter is started when a logic 0 is detected on RxD (see Figure 13-22). A logic 0 on RxD on enabling the bit time measurement with ACLK = 1 leads to immediate start of the counter (see Figure 13-23). The counter will be stopped on the next rising edge of RxD. This mode is used to measure the length of a received break. MEASURED TIME RXD COUNTER STARTS, ARUN = 1 Freescale Semiconductor, Inc... Figure 13-21. Bit Time Measurement with ACLK = 0 MEASURED TIME RXD CPU WRITES SCIACTL WITH $30 COUNTER STARTS, ARUN = 1 CPU WRITES SCIACTL WITH $20 Figure 13-22. Bit Time Measurement with ACLK = 1, Scenario A MEASURED TIME RXD COUNTER STARTS, ARUN = 1 COUNTER STOPS, AFIN = 1 Figure 13-23. Bit Time Measurement with ACLK = 1, Scenario B Data Sheet 182 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com CPU WRITES SCIACTL WITH $30 CPU READS RESULT OUT OF SCIADAT COUNTER STOPS, AFIN = 1 CPU READS RESULT OUT OF SCIADAT CPU READS RESULT OUT OF SCIADAT COUNTER STOPS, AFIN = 1 Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module ESCI Arbiter 13.9.4 Arbitration Mode If AM[1:0] is set to 10, the arbiter module operates in arbitration mode. On every rising edge of SCI_TxD (output of the ESCI module, internal chip signal), the counter is started. When the counter reaches $38 (ACLK = 0) or $08 (ACLK = 1), RxD is statically sensed. If in this case, RxD is sensed low (for example, another bus is driving the bus dominant) ALOST is set. As long as ALOST is set, the TxD pin is forced to 1, resulting in a seized transmission. If SCI_TxD is sensed logic 0 without having sensed a logic 0 before on RxD, the counter will be reset, arbitration operation will be restarted after the next rising edge of SCI_TxD. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Enhanced Serial Communications Interface (ESCI) Module Data Sheet 183 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Enhanced Serial Communications Interface (ESCI) Module Freescale Semiconductor, Inc... Data Sheet 184 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Enhanced Serial Communications Interface (ESCI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Advance Information -- MC68HC908EY16 Section 14. System Integration Module (SIM) 14.1 Introduction This section describes the system integration module (SIM), which supports up to 24 external and/or internal interrupts. The SIM is a system state controller that coordinates the central processor unit (CPU) and exception timing. Together with the CPU, the SIM controls all microcontroller unit (MCU) activities. A block diagram of the SIM is shown in Figure 14-1. The SIM is responsible for: * Bus clock generation and control for CPU and peripherals: - Stop/wait/reset entry and recovery - Internal clock control Master reset control, including power-on reset (POR) and computer operating properly (COP) timeout Interrupt control: - Acknowledge timing - Arbitration control timing - Vector address generation CPU enable/disable timing Modular architecture expandable to 128 interrupt sources Freescale Semiconductor, Inc... * * * * Table 14-1 shows the internal signal names used in this section. Table 14-1. Signal Name Conventions Signal Name CGMXCLK CGMOUT IAB IDB PORRST IRST R/W Description Selected clock source from internal clock generator module (ICG) Clock output from ICG module (bus clock = CGMOUT divided by two) Internal address bus Internal data bus Signal from the power-on reset (POR) module to the SIM Internal reset signal Read/write signal MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA System Integration Module (SIM) Data Sheet 185 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) MODULE STOP MODULE WAIT STOP/WAIT CONTROL CPU STOP (FROM CPU) CPU WAIT (FROM CPU) SIMOSCEN (TO ICG) SIM COUNTER COP CLOCK CGMXCLK (FROM ICG) CGMOUT (FROM ICG) Freescale Semiconductor, Inc... /2 CLOCK CONTROL CLOCK GENERATORS INTERNAL CLOCKS FORCED MON MODE ENTRY (FROM MENRST MODULE) POR CONTROL MASTER RESET CONTROL SIM RESET STATUS REGISTER LVI (FROM LVI MODULE) ILLEGAL OPCODE (FROM CPU) ILLEGAL ADDRESS (FROM ADDRESS MAP DECODERS) COP (FROM COP MODULE) RESET INTERRUPT CONTROL AND PRIORITY DECODE INTERRUPT SOURCES CPU INTERFACE Figure 14-1. SIM Block Diagram Data Sheet 186 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 System Integration Module (SIM) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) SIM Bus Clock Control and Generation 14.2 SIM Bus Clock Control and Generation The bus clock generator provides system clock signals for the CPU and peripherals on the MCU. The system clocks are generated from an incoming clock, CGMOUT, as shown in Figure 14-2. This clock originates from either an external oscillator or from the internal clock generator. CGMXCLK ECLK CLOCK SELECT CIRCUIT SIM COUNTER /2 A CGMOUT Freescale Semiconductor, Inc... ICLK ICG GENERATOR CS B S* *WHEN S = 1, CGMOUT = B /2 BUS CLOCK GENERATORS SIM MONITOR MODE USER MODE ICG Figure 14-2. System Clock Signals 14.2.1 Bus Timing In user mode, the internal bus frequency is the internal clock generator output (CGMXCLK) divided by four. 14.2.2 Clock Startup from POR or LVI Reset When the power-on reset (POR) module or the low-voltage inhibit (LVI) module generates a reset, the clocks to the CPU and peripherals are inactive and held in an inactive phase until after 4096 CGMXCLK cycles. The MCU is held in reset by the SIM during this entire period. The bus clocks start upon completion of the timeout. 14.2.3 Clocks in Stop Mode and Wait Mode Upon exit from stop mode by an interrupt or reset, the SIM allows CGMXCLK to clock the SIM counter. The CPU and peripheral clocks do not become active until after the stop delay timeout. Stop mode recovery timing is discussed in detail in 14.6.2 Stop Mode. In wait mode, the CPU clocks are inactive. Refer to the wait mode subsection of each module to see if the module is active or inactive in wait mode. Some modules can be programmed to be active in wait mode. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA System Integration Module (SIM) Data Sheet 187 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) 14.3 Reset and System Initialization The MCU has these internal reset sources: * * * * * * Power-on reset (POR) module Computer operating properly (COP) module Low-voltage inhibit (LVI) module Illegal opcode Illegal address Forced monitor mode entry reset (MENRST) module Freescale Semiconductor, Inc... All of these resets produce the vector $FFFE-$FFFF ($FEFE-$FEFF in monitor mode) and assert the internal reset signal (IRST). IRST causes all registers to be returned to their default values and all modules to be returned to their reset states. These internal resets clear the SIM counter and set a corresponding bit in the SIM reset status register (SRSR). See 14.4 SIM Counter and 14.7.2 SIM Reset Status Register. 14.3.1 External Pin Reset The RST pin circuit includes an internal pullup device. Pulling the asynchronous RST pin low halts all processing. The PIN bit of the SIM reset status register (SRSR) is set as long as RST is held low for a minimum of 67 CGMXCLK cycles, assuming that neither the POR nor the LVI was the source of the reset. Refer to Table 14-2 for details. Figure 14-3 shows the relative timing. Table 14-2. PIN Bit Set Timing Reset Type POR/LVI All Others Number of Cycles Required to set PIN 4163 (4096 + 64 + 3) 67 (64 + 3) CGMOUT RST IAB PC VECT H VECT L Figure 14-3. External Reset Timing Data Sheet 188 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 System Integration Module (SIM) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) Reset and System Initialization 14.3.2 Active Resets from Internal Sources An internal reset can be caused by an illegal address, illegal opcode, COP timeout, LVI, POR, or MENRST as shown in Figure 14-4. NOTE: For LVI or POR resets, the SIM cycles through 4096 CGMXCLK cycles during which the SIM asserts IRST. The internal reset signal then follows with the 64-cycle phase as shown in Figure 14-5. The COP reset is asynchronous to the bus clock. ILLEGAL ADDRESS RESET ILLEGAL OPCODE RESET COP RESET LVI POR MENRST Freescale Semiconductor, Inc... INTERNAL RESET Figure 14-4. Sources of Internal Reset RST RST PULLED LOW BY MCU 32 CYCLES CGMXCLK IAB 32 CYCLES VECTOR HIGH Figure 14-5. Internal Reset Timing 14.3.2.1 Power-On Reset When power is first applied to the MCU, the power-on reset (POR) module generates a pulse to indicate that power-on has occurred. The MCU is held in reset while the SIM counter counts out 4096 CGMXCLK cycles. Another 64 CGMXCLK cycles later, the CPU and memories are released from reset to allow the reset vector sequence to occur. At power-on, these events occur: * * * * * A POR pulse is generated. The internal reset signal is asserted. The SIM enables CGMOUT. Internal clocks to the CPU and modules are held inactive for 4096 CGMXCLK cycles to allow stabilization of the internal clock generator. The POR bit of the SIM reset status register (SRSR) is set and all other bits in the register are cleared. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA System Integration Module (SIM) Data Sheet 189 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) OSC1 PORRST 4096 CYCLES 32 CYCLES CGMXCLK CGMOUT Freescale Semiconductor, Inc... RST IAB $FFFE $FFFF Figure 14-6. POR Recovery 14.3.2.2 Computer Operating Properly (COP) Reset An input to the SIM is reserved for the COP reset signal. The overflow of the COP counter causes an internal reset and sets the COP bit in the reset status register (SRSR). To prevent a COP module timeout, write any value to location $FFFF. Writing to location $FFFF clears the COP counter and stages 12-5 of the SIM counter. The SIM counter output, which occurs at least every 212-24 CGMXCLK cycles, drives the COP counter. The COP should be serviced as soon as possible out of reset to guarantee the maximum amount of time before the first timeout. The COP module is disabled if the IRQ pin is held at VTST while the MCU is in monitor mode. The COP module can be disabled only through combinational logic conditioned with the high-voltage signal on the IRQ pin. This prevents the COP from becoming disabled as a result of external noise. 14.3.2.3 Illegal Opcode Reset The SIM decodes signals from the CPU to detect illegal instructions. An illegal instruction sets the ILOP bit in the SIM reset status register (SRSR) and causes a reset. If the stop enable bit, STOP, in the configuration register (CONFIG1) is 0, the SIM treats the STOP instruction as an illegal opcode and causes an illegal opcode reset. 14.3.2.4 Illegal Address Reset An opcode fetch from an unmapped address generates an illegal address reset. The SIM verifies that the CPU is fetching an opcode prior to asserting the ILAD bit Data Sheet 190 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 System Integration Module (SIM) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) SIM Counter in the SIM reset status register (SRSR) and resetting the MCU. A data fetch from an unmapped address does not generate a reset. 14.3.2.5 Forced Monitor Mode Entry Reset (MENRST) The MENRST module is monitoring the reset vector fetches and will assert an internal reset if it detects that the reset vectors are erased ($00). When the MCU comes out of reset, it is forced into monitor mode. See 19.3 Monitor Module (MON). 14.3.2.6 Low-Voltage Inhibit (LVI) Reset Freescale Semiconductor, Inc... The low-voltage inhibit module (LVI) asserts its output to the SIM when the VDD voltage falls to the VTRIPF voltage. The LVI bit in the SIM reset status register (SRSR) is set and a chip reset is asserted if the LVIPWRD and LVIRSTD bits in the CONFIG register are at 0. The MCU is held in reset until VDD rises above VTRIPR. The MCU remains in reset until the SIM counts 4096 CGMXCLK to begin a reset recovery. Another 64 CGMXCLK cycles later, the CPU is released from reset to allow the reset vector sequence to occur. See Section 11. Low-Voltage Inhibit (LVI) Module. 14.4 SIM Counter The SIM counter is used by the power-on reset module (POR) and in stop mode recovery to allow the oscillator time to stabilize before enabling the internal bus (IBUS) clocks. The SIM counter also serves as a prescaler for the computer operating properly module (COP). The SIM counter overflow supplies the clock for the COP module. The SIM counter is 12 bits long and is clocked by the falling edge of CGMXCLK. 14.4.1 SIM Counter During Power-On Reset The power-on reset module (POR) detects power applied to the MCU. At power-on, the POR circuit asserts the signal PORRST. Once the SIM is initialized, it enables the internal clock generator to drive the bus clock state machine. 14.4.2 SIM Counter During Stop Mode Recovery The SIM counter also is used for stop mode recovery. The STOP instruction clears the SIM counter. After an interrupt or reset, the SIM senses the state of the short stop recovery bit, SSREC, in the configuration register. If the SSREC bit is a 1, then the stop recovery is reduced from the normal delay of 4096 CGMXCLK cycles down to 32 CGMXCLK cycles. 14.4.3 SIM Counter and Reset States The SIM counter is free-running after all reset states. See 14.3.2 Active Resets from Internal Sources for counter control and internal reset recovery sequences. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA System Integration Module (SIM) Data Sheet 191 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) 14.5 Program Exception Control Normal, sequential program execution can be changed in two ways: 1. Interrupts a. Maskable hardware CPU interrupts b. Non-maskable software interrupt instruction (SWI) 2. Reset 14.5.1 Interrupts Freescale Semiconductor, Inc... At the beginning of an interrupt, the CPU saves the CPU register contents on the stack and sets the interrupt mask (I bit) to prevent additional interrupts. At the end of an interrupt, the return-from-interrupt (RTI) instruction recovers the CPU register contents from the stack so that normal processing can resume. Figure 14-7 shows interrupt entry timing. Figure 14-8 shows interrupt recovery timing. MODULE INTERRUPT I BIT IAB DUMMY SP SP - 1 SP - 2 SP - 3 SP - 4 VECT H VECT L START ADDR IDB DUMMY PC - 1[7:0] PC - 1[15:8] X A CCR V DATA H V DATA L OPCODE R/W Figure 14-7. Interrupt Entry MODULE INTERRUPT I BIT IAB SP - 4 SP - 3 SP - 2 SP - 1 SP PC PC + 1 IDB CCR A X PC - 1 [7:0] PC - 1 [15:8] OPCODE OPERAND R/W Figure 14-8. Interrupt Recovery Data Sheet 192 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 System Integration Module (SIM) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) Program Exception Control Interrupts are latched, and arbitration is performed in the SIM at the start of interrupt processing. The arbitration result is a constant that the CPU uses to determine which vector to fetch. As shown in Figure 14-9, once an interrupt is latched by the SIM, no other interrupt can take precedence, regardless of priority, until the latched interrupt is serviced or the I bit is cleared. FROM RESET YES BIT SET? IIBIT SET? NO IRQ INTERRUPT ? NO YES Freescale Semiconductor, Inc... ICG CLK MON INTERRUPT ? NO YES OTHER INTERRUPTS ? NO YES STACK CPU REGISTERS SET I BIT LOAD PC WITH INTERRUPT VECTOR FETCH NEXT INSTRUCTION SWI INSTRUCTION ? NO RTI INSTRUCTION ? NO YES YES UNSTACK CPU REGISTERS EXECUTE INSTRUCTION Figure 14-9. Interrupt Processing MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA System Integration Module (SIM) Data Sheet 193 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) 14.5.1.1 Hardware Interrupts A hardware interrupt does not stop the current instruction. Processing of a hardware interrupt begins after completion of the current instruction. When the current instruction is complete, the SIM checks all pending hardware interrupts. If interrupts are not masked (I bit clear in the condition code register), and if the corresponding interrupt enable bit is set, the SIM proceeds with interrupt processing; otherwise, the next instruction is fetched and executed. If more than one interrupt is pending at the end of an instruction execution, the highest priority interrupt is serviced first. Figure 14-10 demonstrates what happens when two interrupts are pending. If an interrupt is pending upon exit from the original interrupt service routine, the pending interrupt is serviced before the load-accumulator- from-memory (LDA) instruction is executed. CLI LDA #$FF BACKGROUND ROUTINE Freescale Semiconductor, Inc... INT1 PSHH INT1 INTERRUPT SERVICE ROUTINE PULH RTI INT2 PSHH INT2 INTERRUPT SERVICE ROUTINE PULH RTI Figure 14-10. Interrupt Recognition Example The LDA opcode is prefetched by both the INT1 and INT2 RTI instructions. However, in the case of the INT1 RTI prefetch, this is a redundant operation. NOTE: To maintain compatibility with the M6805, M146805, and MC68HC05 Families the H register is not pushed on the stack during interrupt entry. If the interrupt service routine modifies the H register or uses the indexed addressing mode, software should save the H register and then restore it prior to exiting the routine. Data Sheet 194 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 System Integration Module (SIM) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) Low-Power Modes 14.5.1.2 SWI Instruction The SWI instruction is a non-maskable instruction that causes an interrupt regardless of the state of the interrupt mask (I bit) in the condition code register. NOTE: A software interrupt pushes PC onto the stack. A software interrupt does not push PC - 1, as a hardware interrupt does. 14.5.2 Reset All reset sources always have higher priority than interrupts and cannot be arbitrated. Freescale Semiconductor, Inc... 14.5.3 Break Interrupts The break module can stop normal program flow at a software-programmable break point by asserting its break interrupt output. See 19.2 Break Module (BRK). The SIM puts the CPU into the break state by forcing it to the SWI vector location. Refer to the break interrupt subsection of each module to see how each module is affected by the break state. 14.5.4 Status Flag Protection in Break Mode The SIM controls whether status flags contained in other modules can be cleared during break mode. The user can select whether flags are protected from being cleared by properly initializing the break clear flag enable bit (BCFE) in the SIM break flag control register (SBFCR). Protecting flags in break mode ensures that set flags will not be cleared while in break mode. This protection allows registers to be freely read and written during break mode without losing status flag information. Setting the BCFE bit enables the clearing mechanisms. Once cleared in break mode, a flag remains cleared even when break mode is exited. Status flags with a two-step clearing mechanism -- for example, a read of one register followed by the read or write of another -- are protected, even when the first step is accomplished prior to entering break mode. Upon leaving break mode, execution of the second step will clear the flag as normal. 14.6 Low-Power Modes Executing the WAIT or STOP instruction puts the MCU in a low powerconsumption mode for standby situations. The SIM holds the CPU in a non-clocked state. Both STOP and WAIT clear the interrupt mask (I) in the condition code register, allowing interrupts to occur. Low-power modes are exited via an interrupt or reset. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA System Integration Module (SIM) Data Sheet 195 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) 14.6.1 Wait Mode In wait mode, the CPU clocks are inactive while one set of peripheral clocks continues to run. Figure 14-11 shows the timing for wait mode entry. A module that is active during wait mode can wake up the CPU with an interrupt if the interrupt is enabled. Stacking for the interrupt begins one cycle after the WAIT instruction during which the interrupt occurred. Refer to the wait mode subsection of each module to see if the module is active or inactive in wait mode. Some modules can be programmed to be active in wait mode. Wait mode can also be exited by a reset. If the COP disable bit, COPD, in the configuration register is 0, then the computer operating properly module (COP) is enabled and remains active in wait mode. IAB WAIT ADDR WAIT ADDR + 1 SAME SAME Freescale Semiconductor, Inc... IDB PREVIOUS DATA NEXT OPCODE SAME SAME R/W Note: Previous data can be operand data or the WAIT opcode, depending on the last instruction. Figure 14-11. Wait Mode Entry Timing Figure 14-12 and Figure 14-13 show the timing for WAIT recovery. IAB $DE0B $DE0C $00FF $00FE $00FD $00FC IDB $A6 $A6 $A6 $01 $0B $DE EXITSTOPWAIT Note: EXITSTOPWAIT = CPU interrupt Figure 14-12. Wait Recovery from Interrupt 64 CYCLES IAB $DE0B RST VCT H RST VCT L IDB $A6 $A6 $A6 IRST CGMXCLK Figure 14-13. Wait Recovery from Internal Reset Data Sheet 196 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 System Integration Module (SIM) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) Low-Power Modes 14.6.2 Stop Mode In stop mode, the SIM counter is held in reset and the CPU and peripheral clocks are held inactive. If the STOPOSCEN bit in the configuration register is not enabled, the SIM also disables the internal clock generator module outputs (CGMOUT and CGMXCLK). The CPU and peripheral clocks do not become active until after the stop delay timeout. Stop mode is exited via an interrupt request from a module that is still active in stop mode or from a system reset. An interrupt request from a module that is still active in stop mode can cause an exit from stop mode. Stop recovery time is selectable using the SSREC bit in the configuration register. If SSREC is set, stop recovery is reduced from the normal delay of 4096 CGMXCLK cycles down to 32. Stacking for interrupts begins after the selected stop recovery time has elapsed. When stop mode is exited due to a reset condition, the SIM forces a long stop recovery time of 4096 CGMXCLK cycles. NOTE: Short stop recovery is ideal for applications using canned oscillators that do not require long startup times for stop mode. External crystal applications should use the full stop recovery time by clearing the SSREC bit. The SIM counter is held in reset from the execution of the STOP instruction until the beginning of stop recovery. It is then used to time the recovery period. Figure 14-14 shows stop mode entry timing. CPUSTOP Freescale Semiconductor, Inc... IAB STOP ADDR STOP ADDR + 1 SAME SAME IDB PREVIOUS DATA NEXT OPCODE SAME SAME R/W Note: Previous data can be operand data or the STOP opcode, depending on the last instruction. Figure 14-14. Stop Mode Entry Timing STOP RECOVERY PERIOD CGMXCLK INT IAB STOP +1 STOP + 2 STOP + 2 SP SP - 1 SP - 2 SP - 3 Figure 14-15. Stop Mode Recovery from Interrupt MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA System Integration Module (SIM) Data Sheet 197 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) 14.7 SIM Registers The SIM has three memory mapped registers. Table 14-3 shows the mapping of these registers. Table 14-3. SIM Registers Address $FE00 $FE01 $FE03 Register SBSR SRSR SBFCR Access Mode User User User Freescale Semiconductor, Inc... 14.7.1 SIM Break Status Register The SIM break status register (SBSR) contains a flag to indicate that a break caused an exit from stop or wait mode. Address: $FE00 Bit 7 Read: Write: Reset: R 0 R 6 R 0 = Reserved 5 R 0 4 R 0 3 R 0 2 R 0 1 SBSW Note(1) 0 Bit 0 R 0 Note: 1. Writing a 0 clears SBSW Figure 14-16. SIM Break Status Register (SBSR) SBSW -- SIM Break STOP/WAIT SBSW can be read within the break state SWI routine. The user can modify the return address on the stack by subtracting one from it. 1 = Wait mode was exited by break interrupt 0 = Wait mode was not exited by break interrupt Data Sheet 198 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 System Integration Module (SIM) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) SIM Registers 14.7.2 SIM Reset Status Register This register contains seven bits that show the source of the last reset. The status register will clear automatically after reading it. A power-on reset sets the POR bit and clears all other bits in the register. Address: Read: Write: POR: 1 0 0 0 0 0 0 0 = Unimplemented $FE01 Bit 7 POR 6 PIN 5 COP 4 ILOP 3 ILAD 2 MENRST 1 LVI Bit 0 0 Freescale Semiconductor, Inc... Figure 14-17. SIM Reset Status Register (SRSR) POR -- Power-On Reset Bit 1 = Last reset caused by POR circuit 0 = Read of SRSR PIN -- External Reset Bit 1 = Last reset caused by external reset pin RST 0 = POR or read of SPSR COP -- Computer Operating Properly Reset Bit 1 = Last reset caused by COP counter 0 = POR or read of SRSR ILOP -- Illegal Opcode Reset Bit 1 = Last reset caused by an illegal opcode 0 = POR or read of SRSR ILAD -- Illegal Address Reset Bit (opcode fetches only) 1 = Last reset caused by an opcode fetch from an illegal address 0 = POR or read of SRSR MENRST -- Forced Monitor Mode Entry Reset Bit 1 = Last reset was caused by the MENRST circuit 0 = POR or read of SRSR LVI -- Low-Voltage Inhibit Reset Bit 1 = Last reset was caused by the LVI circuit 0 = POR or read of SRSR MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA System Integration Module (SIM) Data Sheet 199 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. System Integration Module (SIM) 14.7.3 SIM Break Flag Control Register The SIM break flag control register (SBFCR) contains a bit that enables software to clear status bits while the MCU is in a break state. Address: $FE03 Bit 7 Read: Write: Reset: BCFE 0 R 6 R 0 = Reserved 5 R 0 4 R 0 3 R 0 2 R 0 1 R 0 Bit 0 R 0 Freescale Semiconductor, Inc... Figure 14-18. SIM Break Flag Control Register (SBFCR) BCFE -- Break Clear Flag Enable Bit This read/write bit enables software to clear status bits by accessing status registers while the MCU is in a break state. To clear status bits during the break state, the BCFE bit must be set. 1 = Status bits clearable during break 0 = Status bits not clearable during break Data Sheet 200 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 System Integration Module (SIM) MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 15. Serial Peripheral Interface (SPI) Module 15.1 Introduction This section describes the serial peripheral interface (SPI) module, which allows full-duplex, synchronous, serial communications with peripheral devices. Freescale Semiconductor, Inc... 15.2 Features Features of the SPI module include: * * * * * * * Full-duplex operation Master and slave modes Double-buffered operation with separate transmit and receive registers Four master mode frequencies (maximum = bus frequency / 2) Maximum slave mode frequency = bus frequency Serial clock with programmable polarity and phase Two separately enabled interrupts with CPU service: - SPRF (SPI receiver full) - SPTE (SPI transmitter empty) Mode fault error flag with CPU interrupt capability Overflow error flag with CPU interrupt capability Programmable wired-OR mode I2C (inter-integrated circuit) compatibility * * * * 15.3 Pin Name and Register Name Conventions The generic names of the SPI input/output (I/O) pins are: * * * * SS (slave select) SPSCK (SPI serial clock) MOSI (master out slave in) MISO (master in slave out) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 201 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module INTERNAL BUS M68HC08 CPU CPU REGISTERS ARITHMETIC/LOGIC UNIT (ALU) SINGLE BREAKPOINT BREAK MODULE PORT A DDRA 5-BIT KEYBOARD INTERRUPT MODULE PTA6/SS PTA5/SPSCK PTA4/KBD4 PTA3/KBD3 PTA2/KBD2 PTA1/KBD1 2-CHANNEL TIMER INTERFACE MODULE A PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PORT B DDRB PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK PTC1/MOSI PTC0/MISO PTD1/TACH1 PTD0/TACH0 PTE1/RxD PTE0/TxD PORT C PORT E PORT D CONTROL AND STATUS REGISTERS 64 BYTES USER FLASH 15,872 BYTES USER RAM 512 BYTES Freescale Semiconductor, Inc... MONITOR ROM 310 BYTES FLASH PROGRAMMING (BURN-IN) ROM 1024 BYTES USER FLASH VECTOR SPACE 36 BYTES 2-CHANNEL TIMER INTERFACE MODULE B ENHANCED SERIAL COMMUNICATION INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE OSC2 OSC1 INTERNAL CLOCK GENERATOR MODULE SERIAL PERIPHERAL INTERFACE MODULE RST 24 INTERNAL SYSTEM INTEGRATION MODULE SINGLE EXTERNAL IRQ MODULE CONFIGURATION REGISTER MODULE PERIODIC WAKEUP TIMEBASE MODULE ARBITER MODULE PRESCALER MODULE IRQ VREFH VDDA VREFL VSSA VDD VSS DDRE DDRD DDRC 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE SECURITY MODULE POWER BEMF MODULE Figure 15-1. Block Diagram Highlighting SPI Block and Pins Data Sheet 202 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module Functional Description The SPI shares four I/O pins with a parallel I/O port. The full name of an SPI pin reflects the name of the shared port pin. Table 15-1 shows the full names of the SPI I/O pins. The generic pin names appear in the text that follows. Table 15-1. Pin Name Conventions SPI Generic Pin Name Full SPI Pin Name MISO PTC0/MISO MOSI PTC1/MOSI SS PTA6/SS SPSCK PTA5/SPSCK The generic names of the SPI I/O registers are: * SPI control register (SPCR) SPI status and control register (SPSCR) SPI data register (SPDR) * * Freescale Semiconductor, Inc... Table 15-2 shows the names and the addresses of the SPI I/O registers. Table 15-2. I/O Register Addresses Register Name SPI control register (SPCR) SPI status and control register (SPSCR) SPI data register (SPDR) Address $000D $000E $000F 15.4 Functional Description Table 15-3 summarizes the SPI I/O registers and Figure 15-2 shows the structure of the SPI module. Table 15-3. SPI I/O Register Summary Addr $000D Register Name SPI Control Register (SPCR) Write: See page 220. Reset: SPI Status and Control Register Read: (SPSCR) Write: See page 221. Reset: SPI Data Register Read: (SPDR) Write: See page 224. Reset: Read: Bit 7 SPRIE 0 SPRF 0 R7 T7 R 6 R 0 ERRIE 0 R6 T6 = Reserved 5 SPMSTR 1 OVRF 0 R5 T5 4 CPOL 0 MODF 0 R4 T4 3 CPHA 1 SPTE 1 R3 T3 2 SPWOM 0 MODFEN 0 R2 T2 1 SPE 0 SPR1 0 R1 T1 Bit 0 SPTIE 0 SPR0 0 R0 T0 $000E $000F Unaffected by Reset = Unimplemented MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 203 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module INTERNAL BUS TRANSMIT DATA REGISTER BUS CLOCK 7 /2 CLOCK DIVIDER /8 / 32 / 128 CLOCK SELECT 6 SHIFT REGISTER 5 4 3 2 1 0 MISO MOSI RECEIVE DATA REGISTER PIN CONTROL LOGIC SPSCK CLOCK LOGIC M S SS Freescale Semiconductor, Inc... SPMSTR SPE SPR1 SPR0 SPMSTR CPHA CPOL TRANSMITTER CPU INTERRUPT REQUEST SPI CONTROL RECEIVER/ERROR CPU INTERRUPT REQUEST MODFEN ERRIE SPTIE SPRIE SPE SPRF SPTE OVRF MODF SPWOM Figure 15-2. SPI Module Block Diagram The SPI module allows full-duplex, synchronous, serial communication between the MCU and peripheral devices, including other MCUs. Software can poll the SPI status flags or SPI operation can be interrupt driven. All SPI interrupts can be serviced by the CPU. The following paragraphs describe the operation of the SPI module. Data Sheet 204 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module Functional Description 15.4.1 Master Mode The SPI operates in master mode when the SPI master bit, SPMSTR (SPCR $0010), is set. NOTE: Configure the SPI modules as master and slave before enabling them. Enable the master SPI before enabling the slave SPI. Disable the slave SPI before disabling the master SPI. See 15.13.1 SPI Control Register. Only a master SPI module can initiate transmissions. Software begins the transmission from a master SPI module by writing to the SPI data register. If the shift register is empty, the byte immediately transfers to the shift register, setting the SPI transmitter empty bit, SPTE (SPSCR $0011). The byte begins shifting out on the MOSI pin under the control of the serial clock. (See Table 15-4). The SPR1 and SPR0 bits control the baud rate generator and determine the speed of the shift register. (See 15.13.2 SPI Status and Control Register.) Through the SPSCK pin, the baud rate generator of the master also controls the shift register of the slave peripheral. MASTER MCU MISO MISO SLAVE MCU Freescale Semiconductor, Inc... SHIFT REGISTER MOSI MOSI SHIFT REGISTER SPSCK BAUD RATE GENERATOR SPSCK SS VDD SS Figure 15-3. Full-Duplex Master-Slave Connections As the byte shifts out on the MOSI pin of the master, another byte shifts in from the slave on the master's MISO pin. The transmission ends when the receiver full bit, SPRF (SPSCR), becomes set. At the same time that SPRF becomes set, the byte from the slave transfers to the receive data register. In normal operation, SPRF signals the end of a transmission. Software clears SPRF by reading the SPI status and control register and then reading the SPI data register. Writing to the SPI data register clears the SPTIE bit. 15.4.2 Slave Mode The SPI operates in slave mode when the SPMSTR bit (SPCR, $0010) is clear. In slave mode the SPSCK pin is the input for the serial clock from the master MCU. Before a data transmission occurs, the SS pin of the slave MCU must be at logic 0. SS must remain low until the transmission is complete. (See 15.6.2 Mode Fault Error.) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 205 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module In a slave SPI module, data enters the shift register under the control of the serial clock from the master SPI module. After a byte enters the shift register of a slave SPI, it is transferred to the receive data register, and the SPRF bit (SPSCR) is set. To prevent an overflow condition, slave software then must read the SPI data register before another byte enters the shift register. The maximum frequency of the SPSCK for an SPI configured as a slave is the bus clock speed, which is twice as fast as the fastest master SPSCK clock that can be generated. The frequency of the SPSCK for an SPI configured as a slave does not have to correspond to any SPI baud rate. The baud rate only controls the speed of the SPSCK generated by an SPI configured as a master. Therefore, the frequency of the SPSCK for an SPI configured as a slave can be any frequency less than or equal to the bus speed. When the master SPI starts a transmission, the data in the slave shift register begins shifting out on the MISO pin. The slave can load its shift register with a new byte for the next transmission by writing to its transmit data register. The slave must write to its transmit data register at least one bus cycle before the master starts the next transmission. Otherwise the byte already in the slave shift register shifts out on the MISO pin. Data written to the slave shift register during a a transmission remains in a buffer until the end of the transmission. When the clock phase bit (CPHA) is set, the first edge of SPSCK starts a transmission. When CPHA is clear, the falling edge of SS starts a transmission. (See 15.5 Transmission Formats.) If the write to the data register is late, the SPI transmits the data already in the shift register from the previous transmission. NOTE: To prevent SPSCK from appearing as a clock edge, SPSCK must be in the proper idle state before the slave is enabled. Freescale Semiconductor, Inc... 15.5 Transmission Formats During an SPI transmission, data is simultaneously transmitted (shifted out serially) and received (shifted in serially). A serial clock line synchronizes shifting and sampling on the two serial data lines. A slave select line allows individual selection of a slave SPI device; slave devices that are not selected do not interfere with SPI bus activities. On a master SPI device, the slave select line can be used optionally to indicate a multiple-master bus contention. 15.5.1 Clock Phase and Polarity Controls Software can select any of four combinations of serial clock (SCK) phase and polarity using two bits in the SPI control register (SPCR). The clock polarity is specified by the CPOL control bit, which selects an active high or low clock and has no significant effect on the transmission format. Data Sheet 206 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module Transmission Formats The clock phase (CPHA) control bit (SPCR) selects one of two fundamentally different transmission formats. The clock phase and polarity should be identical for the master SPI device and the communicating slave device. In some cases, the phase and polarity are changed between transmissions to allow a master device to communicate with peripheral slaves having different requirements. NOTE: Before writing to the CPOL bit or the CPHA bit (SPCR), disable the SPI by clearing the SPI enable bit (SPE). 15.5.2 Transmission Format When CPHA = 0 Figure 15-4 shows an SPI transmission in which CPHA (SPCR) is 0. The figure should not be used as a replacement for data sheet parametric information. Two waveforms are shown for SCK: one for CPOL = 0 and another for CPOL = 1. The diagram may be interpreted as a master or slave timing diagram since the serial clock (SCK), master in/slave out (MISO), and master out/slave in (MOSI) pins are directly connected between the master and the slave. The MISO signal is the output from the slave, and the MOSI signal is the output from the master. The SS line is the slave select input to the slave. The slave SPI drives its MISO output only when its slave select input (SS) is at logic 0, so that only the selected slave drives to the master. The SS pin of the master is not shown but is assumed to be inactive. The SS pin of the master must be high or must be reconfigured as general-purpose I/O not affecting the SPI (see 15.6.2 Mode Fault Error). When CPHA = 0, the first SPSCK edge is the MSB capture strobe. Therefore, the slave must begin driving its data before the first SPSCK edge, and a falling edge on the SS pin is used to start the transmission. The SS pin must be toggled high and then low again between each byte transmitted. SCK CYCLE # FOR REFERENCE SCK CPOL = 0 Freescale Semiconductor, Inc... 1 2 3 4 5 6 7 8 SCK CPOL = 1 MOSI FROM MASTER MISO FROM SLAVE SS TO SLAVE CAPTURE STROBE MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB Figure 15-4. Transmission Format (CPHA = 0) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 207 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module 15.5.3 Transmission Format When CPHA = 1 Figure 15-5 shows an SPI transmission in which CPHA (SPCR) is 1. The figure should not be used as a replacement for data sheet parametric information. Two waveforms are shown for SCK: one for CPOL = 0 and another for CPOL = 1. The diagram may be interpreted as a master or slave timing diagram since the serial clock (SCK), master in/slave out (MISO), and master out/slave in (MOSI) pins are directly connected between the master and the slave. The MISO signal is the output from the slave, and the MOSI signal is the output from the master. The SS line is the slave select input to the slave. The slave SPI drives its MISO output only when its slave select input (SS) is at logic 0, so that only the selected slave drives to the master. The SS pin of the master is not shown but is assumed to be inactive. The SS pin of the master must be high or must be reconfigured as general-purpose I/O not affecting the SPI. (See 15.6.2 Mode Fault Error.) When CPHA = 1, the master begins driving its MOSI pin on the first SPSCK edge. Therefore, the slave uses the first SPSCK edge as a start transmission signal. The SS pin can remain low between transmissions. This format may be preferable in systems having only one master and only one slave driving the MISO data line. Freescale Semiconductor, Inc... SCK CYCLE # FOR REFERENCE 1 2 3 4 5 6 7 8 SCK CPOL = 0 SCK CPOL =1 MOSI FROM MASTER MISO FROM SLAVE MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB SS TO SLAVE CAPTURE STROBE Figure 15-5. Transmission Format (CPHA = 1) Data Sheet 208 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module Error Conditions 15.5.4 Transmission Initiation Latency When the SPI is configured as a master (SPMSTR = 1), transmissions are started by a software write to the SPDR ($0012). CPHA has no effect on the delay to the start of the transmission, but it does affect the initial state of the SCK signal. When CPHA = 0, the SCK signal remains inactive for the first half of the first SCK cycle. When CPHA = 1, the first SCK cycle begins with an edge on the SCK line from its inactive to its active level. The SPI clock rate (selected by SPR1-SPR0) affects the delay from the write to SPDR and the start of the SPI transmission. (See Figure 15-6.) The internal SPI clock in the master is a free-running derivative of the internal MCU clock. It is only enabled when both the SPE and SPMSTR bits (SPCR) are set to conserve power. SCK edges occur half way through the low time of the internal MCU clock. Since the SPI clock is free-running, it is uncertain where the write to the SPDR will occur relative to the slower SCK. This uncertainty causes the variation in the initiation delay shown in Figure 15-6. This delay will be no longer than a single SPI bit time. That is, the maximum delay between the write to SPDR and the start of the SPI transmission is two MCU bus cycles for DIV2, eight MCU bus cycles for DIV8, 32 MCU bus cycles for DIV32, and 128 MCU bus cycles for DIV128. Freescale Semiconductor, Inc... 15.6 Error Conditions Two flags signal SPI error conditions: 1. Overflow (OVRF in SPSCR) -- Failing to read the SPI data register before the next byte enters the shift register sets the OVRF bit. The new byte does not transfer to the receive data register, and the unread byte still can be read by accessing the SPI data register. OVRF is in the SPI status and control register. 2. Mode fault error (MODF in SPSCR) -- The MODF bit indicates that the voltage on the slave select pin (SS) is inconsistent with the mode of the SPI. MODF is in the SPI status and control register. 15.6.1 Overflow Error The overflow flag (OVRF in SPSCR) becomes set if the SPI receive data register still has unread data from a previous transmission when the capture strobe of bit 1 of the next transmission occurs. (See Figure 15-4 and Figure 15-5.) If an overflow occurs, the data being received is not transferred to the receive data register so that the unread data can still be read. Therefore, an overflow error always indicates the loss of data. OVRF generates a receiver/error CPU interrupt request if the error interrupt enable bit (ERRIE in SPSCR) is also set. MODF and OVRF can generate a receiver/error CPU interrupt request. (See Figure 15-9.) It is not possible to enable only MODF or OVRF to generate a receiver/error CPU interrupt request. However, leaving MODFEN low prevents MODF from being set. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 209 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module WRITE TO SPDR BUS CLOCK MOSI SCK CPHA = 1 SCK CPHA = 0 SCK CYCLE NUMBER INITIATION DELAY MSB BIT 6 BIT 5 Freescale Semiconductor, Inc... 1 2 3 INITIATION DELAY FROM WRITE SPDR TO TRANSFER BEGIN BUS CLOCK BUS CLOCK BUS CLOCK BUS CLOCK WRITE TO SPDR EARLIEST LATEST WRITE TO SPDR EARLIEST WRITE TO SPDR EARLIEST WRITE TO SPDR EARLIEST Figure 15-6. Transmission Start Delay (Master) If an end-of-block transmission interrupt was meant to pull the MCU out of wait, having an overflow condition without overflow interrupts enabled causes the MCU to hang in wait mode. If the OVRF is enabled to generate an interrupt, it can pull the MCU out of wait mode instead. If the CPU SPRF interrupt is enabled and the OVRF interrupt is not, watch for an overflow condition. Figure 15-7 shows how it is possible to miss an overflow. SCK = INTERNAL CLOCK / 2; 2 POSSIBLE START POINTS SCK = INTERNAL CLOCK / 8; 8 POSSIBLE START POINTS LATEST SCK = INTERNAL CLOCK / 32; 32 POSSIBLE START POINTS LATEST SCK = INTERNAL CLOCK / 128; 128 POSSIBLE START POINTS LATEST Data Sheet 210 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module Error Conditions BYTE 1 1 BYTE 2 4 BYTE 3 6 BYTE 4 8 SPRF OVRF READ SPSCR READ SPDR 1 BYTE 1 SETS SPRF BIT. CPU READS SPSCR WITH SPRF BIT SET AND OVRF BIT CLEAR. CPU READS BYTE 1 IN SPDR, CLEARING SPRF BIT. BYTE 2 SETS SPRF BIT. 2 5 3 5 6 7 8 7 CPU READS SPSCRW WITH SPRF BIT SET AND OVRF BIT CLEAR. BYTE 3 SETS OVRF BIT. BYTE 3 IS LOST. CPU READS BYTE 2 IN SPDR, CLEARING SPRF BIT, BUT NOT OVRF BIT. BYTE 4 FAILS TO SET SPRF BIT BECAUSE OVRF BIT IS SET. BYTE 4 IS LOST. Freescale Semiconductor, Inc... 2 3 4 Figure 15-7. Missed Read of Overflow Condition The first part of Figure 15-7 shows how to read the SPSCR and SPDR to clear the SPRF without problems. However, as illustrated by the second transmission example, the OVRF flag can be set in between the time that SPSCR and SPDR are read. In this case, an overflow can be easily missed. Since no more SPRF interrupts can be generated until this OVRF is serviced, it will not be obvious that bytes are being lost as more transmissions are completed. To prevent this, either enable the OVRF interrupt or do another read of the SPSCR after the read of the SPDR. This ensures that the OVRF was not set before the SPRF was cleared and that future transmissions will complete with an SPRF interrupt. Figure 15-8 illustrates this process. Generally, to avoid this second SPSCR read, enable the OVRF to the CPU by setting the ERRIE bit (SPSCR). 15.6.2 Mode Fault Error For the MODF flag (in SPSCR) to be set, the mode fault error enable bit (MODFEN in SPSCR) must be set. Clearing the MODFEN bit does not clear the MODF flag but does prevent MODF from being set again after MODF is cleared. MODF generates a receiver/error CPU interrupt request if the error interrupt enable bit (ERRIE in SPSCR) is also set. The SPRF, MODF, and OVRF interrupts share the same CPU interrupt vector. MODF and OVRF can generate a receiver/error CPU interrupt request. (See Figure 15-9). It is not possible to enable only MODF or OVRF to generate a receiver/error CPU interrupt request. However, leaving MODFEN low prevents MODF from being set. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 211 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module BYTE 1 SPI RECEIVE COMPLETE SPRF 1 BYTE 2 5 BYTE 3 7 BYTE 4 11 OVRF 2 4 6 9 8 8 9 12 14 READ SPSCR READ SPDR 3 10 13 Freescale Semiconductor, Inc... 1 2 3 4 5 6 7 BYTE 1 SETS SPRF BIT. CPU READS SPSCR WITH SPRF BIT SET AND OVRF BIT CLEAR. CPU READS BYTE 1 IN SPDR, CLEARING SPRF BIT. CPU READS SPSCR AGAIN TO CHECK OVRF BIT. BYTE 2 SETS SPRF BIT. CPU READS SPSCR WITH SPRF BIT SET AND OVRF BIT CLEAR. BYTE 3 SETS OVRF BIT. BYTE 3 IS LOST. CPU READS BYTE 2 IN SPDR, CLEARING SPRF BIT. CPU READS SPSCR AGAIN TO CHECK OVRF BIT. 10 CPU READS BYTE 2 SPDR, CLEARING OVRF BIT. 11 BYTE 4 SETS SPRF BIT. 12 CPU READS SPSCR. 13 CPU READS BYTE 4 IN SPDR, CLEARING SPRF BIT. 14 CPU READS SPSCR AGAIN TO CHECK OVRF BIT. Figure 15-8. Clearing SPRF When OVRF Interrupt Is Not Enabled In a master SPI with the mode fault enable bit (MODFEN) set, the mode fault flag (MODF) is set if SS goes to logic 0. A mode fault in a master SPI causes the following events to occur: * * * * * NOTE: NOTE: If ERRIE = 1, the SPI generates an SPI receiver/error CPU interrupt request. The SPE bit is cleared. The SPTE bit is set. The SPI state counter is cleared. The data direction register of the shared I/O port regains control of port drivers. To prevent bus contention with another master SPI after a mode fault error, clear all data direction register (DDR) bits associated with the SPI shared port pins. Setting the MODF flag (SPSCR) does not clear the SPMSTR bit. Reading SPMSTR when MODF = 1 will indicate a MODE fault error occurred in either master mode or slave mode. When configured as a slave (SPMSTR = 0), the MODF flag is set if SS goes high during a transmission. When CPHA = 0, a transmission begins when SS goes low and ends once the incoming SPSCK returns to its idle level after the shift of the eighth data bit. When CPHA = 1, the transmission begins when the SPSCK leaves its idle level and SS is already low. The transmission continues until the SPSCK returns to its IDLE level after the shift of the last data bit. (See 15.5 Transmission Formats.) Data Sheet 212 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module Interrupts NOTE: When CPHA = 0, a MODF occurs if a slave is selected (SS is at logic 0) and later deselected (SS is at logic 1) even if no SPSCK is sent to that slave. This happens because SS at logic 0 indicates the start of the transmission (MISO driven out with the value of MSB) for CPHA = 0. When CPHA = 1, a slave can be selected and then later deselected with no transmission occurring. Therefore, MODF does not occur since a transmission was never begun. In a slave SPI (MSTR = 0), the MODF bit generates an SPI receiver/error CPU interrupt request if the ERRIE bit is set. The MODF bit does not clear the SPE bit or reset the SPI in any way. Software can abort the SPI transmission by toggling the SPE bit of the slave. Freescale Semiconductor, Inc... NOTE: A logic 1 voltage on the SS pin of a slave SPI puts the MISO pin in a high impedance state. Also, the slave SPI ignores all incoming SPSCK clocks, even if a transmission has begun. To clear the MODF flag, read the SPSCR and then write to the SPCR register. This entire clearing procedure must occur with no MODF condition existing or else the flag will not be cleared. 15.7 Interrupts Four SPI status flags can be enabled to generate CPU interrupt requests: Table 15-4. SPI Interrupts Flag SPTE (Transmitter Empty) SPRF (Receiver Full) OVRF (Overflow) MODF (Mode Fault) Request SPI Transmitter CPU Interrupt Request (SPTIE = 1) SPI Receiver CPU Interrupt Request (SPRIE = 1) SPI Receiver/Error Interrupt Request (SPRIE = 1, ERRIE = 1) SPI Receiver/Error Interrupt Request (SPRIE = 1, ERRIE = 1, MODFEN = 1) The SPI transmitter interrupt enable bit (SPTIE) enables the SPTE flag to generate transmitter CPU interrupt requests. The SPI receiver interrupt enable bit (SPRIE) enables the SPRF bit to generate receiver CPU interrupt, provided that the SPI is enabled (SPE = 1). The error interrupt enable bit (ERRIE) enables both the MODF and OVRF flags to generate a receiver/error CPU interrupt request. The mode fault enable bit (MODFEN) can prevent the MODF flag from being set so that only the OVRF flag is enabled to generate receiver/error CPU interrupt requests. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 213 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module SPTE SPTIE SPE SPI TRANSMITTER CPU INTERRUPT REQUEST SPRIE SPRF ERRIE MODF OVRF SPI RECEIVER/ERROR CPU INTERRUPT REQUEST Freescale Semiconductor, Inc... Figure 15-9. SPI Interrupt Request Generation Two sources in the SPI status and control register can generate CPU interrupt requests: 1. SPI receiver full bit (SPRF) -- The SPRF bit becomes set every time a byte transfers from the shift register to the receive data register. If the SPI receiver interrupt enable bit, SPRIE, is also set, SPRF can generate an SPI receiver/error CPU interrupt request. 2. SPI transmitter empty (SPTE) -- The SPTE bit becomes set every time a byte transfers from the transmit data register to the shift register. If the SPI transmit interrupt enable bit, SPTIE, is also set, SPTE can generate an SPTE CPU interrupt request. 15.8 Queuing Transmission Data The double-buffered transmit data register allows a data byte to be queued and transmitted. For an SPI configured as a master, a queued data byte is transmitted immediately after the previous transmission has completed. The SPI transmitter empty flag (SPTE in SPSCR) indicates when the transmit data buffer is ready to accept new data. Write to the SPI data register only when the SPTE bit is high. Figure 15-10 shows the timing associated with doing back-to-back transmissions with the SPI (SPSCK has CPHA:CPOL = 1:0). For a slave, the transmit data buffer allows back-to-back transmissions to occur without the slave having to time the write of its data between the transmissions. Also, if no new data is written to the data buffer, the last value contained in the shift register will be the next data word transmitted. Data Sheet 214 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module Resetting the SPI WRITE TO SPDR 1 3 8 SPTE 2 5 10 SPSCK (CPHA:CPOL = 1:0) MOSI MSB BIT BIT BIT BIT BIT BIT LSB MSB BIT BIT BIT BIT BIT BIT LSB MSB BIT BIT BIT 654321 654321 654 BYTE 1 BYTE 2 BYTE 3 4 9 SPRF Freescale Semiconductor, Inc... READ SPSCR 6 11 READ SPDR 1 2 3 4 CPU WRITES BYTE 1 TO SPDR, CLEARING SPTE BIT. BYTE 1 TRANSFERS FROM TRANSMIT DATA REGISTER TO SHIFT REGISTER, SETTING SPTE BIT. CPU WRITES BYTE 2 TO SPDR, QUEUEING BYTE 2 AND CLEARING SPTE BIT. FIRST INCOMING BYTE TRANSFERS FROM SHIFT REGISTER TO RECEIVE DATA REGISTER, SETTING SPRF BIT. BYTE 2 TRANSFERS FROM TRANSMIT DATA REGISTER TO SHIFT REGISTER, SETTING SPTE BIT. CPU READS SPSCR WITH SPRF BIT SET. 7 8 9 7 CPU READS SPDR, CLEARING SPRF BIT. CPU WRITES BYTE 3 TO SPDR, QUEUEING BYTE 3 AND CLEARING SPTE BIT. 12 SECOND INCOMING BYTE TRANSFERS FROM SHIFT REGISTER TO RECEIVE DATA REGISTER, SETTING SPRF BIT. 10 BYTE 3 TRANSFERS FROM TRANSMIT DATA REGISTER TO SHIFT REGISTER, SETTING SPTE BIT. 11 CPU READS SPSCR WITH SPRF BIT SET. 12 CPU READS SPDR, CLEARING SPRF BIT. 5 6 Figure 15-10. SPRF/SPTE CPU Interrupt Timing 15.9 Resetting the SPI Any system reset completely resets the SPI. Partial reset occurs whenever the SPI enable bit (SPE) is low. Whenever SPE is low, the following occurs: * * * * * The SPTE flag is set. Any transmission currently in progress is aborted. The shift register is cleared. The SPI state counter is cleared, making it ready for a new complete transmission. All the SPI port logic is defaulted back to being general-purpose I/O. The following additional items are reset only by a system reset: * All control bits in the SPCR register * All control bits in the SPSCR register (MODFEN, ERRIE, SPR1, and SPR0) * The status flags SPRF, OVRF, and MODF MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 215 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module By not resetting the control bits when SPE is low, the user can clear SPE between transmissions without having to reset all control bits when SPE is set back to high for the next transmission. By not resetting the SPRF, OVRF, and MODF flags, the user can still service these interrupts after the SPI has been disabled. The user can disable the SPI by writing a 0 to the SPE bit. The SPI also can be disabled by a mode fault occurring in an SPI that was configured as a master with the MODFEN bit set. 15.10 Low-Power Modes Freescale Semiconductor, Inc... The WAIT and STOP instructions put the MCU in low power- consumption standby modes. 15.10.1 Wait Mode The SPI module remains active after the execution of a WAIT instruction. In wait mode, the SPI module registers are not accessible by the CPU. Any enabled CPU interrupt request from the SPI module can bring the MCU out of wait mode. If SPI module functions are not required during wait mode, reduce power consumption by disabling the SPI module before executing the WAIT instruction. To exit wait mode when an overflow condition occurs, enable the OVRF bit to generate CPU interrupt requests by setting the error interrupt enable bit (ERRIE). (See 15.7 Interrupts.) 15.10.2 Stop Mode The SPI module is inactive after the execution of a STOP instruction. The STOP instruction does not affect register conditions. SPI operation resumes after the MCU exits stop mode. If stop mode is exited by reset, any transfer in progress is aborted and the SPI is reset. 15.11 SPI During Break Interrupts The system integration module (SIM) controls whether status bits in other modules can be cleared during the break state. The BCFE bit in the SIM break flag control register (SBFCR, $FE03) enables software to clear status bits during the break state. (See 19.2.1.1 Flag Protection During Break Interrupts.) To allow software to clear status bits during a break interrupt, write a 1 to the BCFE bit. If a status bit is cleared during the break state, it remains cleared when the MCU exits the break state. To protect status bits during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default state), software can read and write I/O registers during the break state without affecting status bits. Some status bits have a two-step read/write Data Sheet 216 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module I/O Signals clearing procedure. If software does the first step on such a bit before the break, the bit cannot change during the break state as long as BCFE is at 0. After the break, doing the second step clears the status bit. Since the SPTE bit cannot be cleared during a break with the BCFE bit cleared, a write to the data register in break mode will not initiate a transmission nor will this data be transferred into the shift register. Therefore, a write to the SPDR in break mode with the BCFE bit cleared has no effect. 15.12 I/O Signals The SPI module has four I/O pins and shares three of them with a parallel I/O port. Freescale Semiconductor, Inc... * * * * * MISO -- Data received MOSI -- Data transmitted SPSCK -- Serial clock SS -- Slave select VSS -- Clock ground The SPI has limited inter-integrated circuit (I2C) capability (requiring software support) as a master in a single-master environment. To communicate with I2C peripherals, MOSI becomes an open-drain output when the SPWOM bit in the SPI control register is set. In I2C communication, the MOSI and MISO pins are connected to a bidirectional pin from the I2C peripheral and through a pullup resistor to VDD. 15.12.1 MISO (Master In/Slave Out) MISO is one of the two SPI module pins that transmit serial data. In full duplex operation, the MISO pin of the master SPI module is connected to the MISO pin of the slave SPI module. The master SPI simultaneously receives data on its MISO pin and transmits data from its MOSI pin. Slave output data on the MISO pin is enabled only when the SPI is configured as a slave. The SPI is configured as a slave when its SPMSTR bit is 0 and its SS pin is at logic 0. To support a multiple-slave system, a logic 1 on the SS pin puts the MISO pin in a high-impedance state. When enabled, the SPI controls data direction of the MISO pin regardless of the state of the data direction register of the shared I/O port. 15.12.2 MOSI (Master Out/Slave In) MOSI is one of the two SPI module pins that transmit serial data. In full duplex operation, the MOSI pin of the master SPI module is connected to the MOSI pin of the slave SPI module. The master SPI simultaneously transmits data from its MOSI pin and receives data on its MISO pin. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 217 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module When enabled, the SPI controls data direction of the MOSI pin regardless of the state of the data direction register of the shared I/O port. 15.12.3 SPSCK (Serial Clock) The serial clock synchronizes data transmission between master and slave devices. In a master MCU, the SPSCK pin is the clock output. In a slave MCU, the SPSCK pin is the clock input. In full duplex operation, the master and slave MCUs exchange a byte of data in eight serial clock cycles. When enabled, the SPI controls data direction of the SPSCK pin regardless of the state of the data direction register of the shared I/O port. Freescale Semiconductor, Inc... 15.12.4 SS (Slave Select) The SS pin has various functions depending on the current state of the SPI. For an SPI configured as a slave, the SS is used to select a slave. For CPHA = 0, the SS is used to define the start of a transmission. (See 15.5 Transmission Formats.) Since it is used to indicate the start of a transmission, the SS must be toggled high and low between each byte transmitted for the CPHA = 0 format. However, it can remain low throughout the transmission for the CPHA = 1 format. See Figure 15-11. MISO/MOSI MASTER SS SLAVE SS CPHA = 0 SLAVE SS CPHA = 1 BYTE 1 BYTE 2 BYTE 3 Figure 15-11. CPHA/SS Timing When an SPI is configured as a slave, the SS pin is always configured as an input. It cannot be used as a general-purpose I/O regardless of the state of the MODFEN control bit. However, the MODFEN bit can still prevent the state of the SS from creating a MODF error. (See 15.13.2 SPI Status and Control Register.) NOTE: A logic 1 voltage on the SS pin of a slave SPI puts the MISO pin in a high-impedance state. The slave SPI ignores all incoming SPSCK clocks, even if a transmission already has begun. When an SPI is configured as a master, the SS input can be used in conjunction with the MODF flag to prevent multiple masters from driving MOSI and SPSCK. (See 15.6.2 Mode Fault Error.) For the state of the SS pin to set the MODF flag, the MODFEN bit in the SPSCK register must be set. If the MODFEN bit is low for an SPI master, the SS pin can be used as a general-purpose I/O under the control of the data direction register of the shared I/O port. With MODFEN high, it is an Data Sheet 218 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module I/O Registers input-only pin to the SPI regardless of the state of the data direction register of the shared I/O port. The CPU can always read the state of the SS pin by configuring the appropriate pin as an input and reading the data register. (See Table 15-5.) Table 15-5. SPI Configuration SPE 0 1 SPMSTR X 0 1 1 MODFEN X X 0 1 SPI Configuration Not Enabled Slave Master without MODF Master with MODF State of SS Logic General-Purpose I/O; SS Ignored by SPI Input-Only to SPI General-Purpose I/O; SS Ignored by SPI Input-Only to SPI Freescale Semiconductor, Inc... 1 1 X = don't care 15.12.5 VSS (Clock Ground) VSS is the ground return for the serial clock pin, SPSCK, and the ground for the port output buffers. To reduce the ground return path loop and minimize radio frequency (RF) emissions, connect the ground pin of the slave to the VSS pin. 15.13 I/O Registers Three registers control and monitor SPI operation: * * * SPI control register (SPCR $0010) SPI status and control register (SPSCR $0011) SPI data register (SPDR $0012) 15.13.1 SPI Control Register The SPI control register: * * * * * * Enables SPI module interrupt requests Selects CPU interrupt requests Configures the SPI module as master or slave Selects serial clock polarity and phase Configures the SPSCK, MOSI, and MISO pins as open-drain outputs Enables the SPI module MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 219 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module Address: Read: Write: Reset: $000D Bit 7 SPRIE 0 R 6 R 0 = Reserved 5 SPMSTR 1 4 CPOL 0 3 CPHA 1 2 SPWOM 0 1 SPE 0 Bit 0 SPTIE 0 Figure 15-12. SPI Control Register (SPCR) SPRIE -- SPI Receiver Interrupt Enable Bit This read/write bit enables CPU interrupt requests generated by the SPRF bit. The SPRF bit is set when a byte transfers from the shift register to the receive data register. Reset clears the SPRIE bit. 1 = SPRF CPU interrupt requests enabled 0 = SPRF CPU interrupt requests disabled SPMSTR -- SPI Master Bit This read/write bit selects master mode operation or slave mode operation. Reset sets the SPMSTR bit. 1 = Master mode 0 = Slave mode CPOL -- Clock Polarity Bit This read/write bit determines the logic state of the SPSCK pin between transmissions. (See Figure 15-4 and Figure 15-5.) To transmit data between SPI modules, the SPI modules must have identical CPOL bits. Reset clears the CPOL bit. CPHA -- Clock Phase Bit This read/write bit controls the timing relationship between the serial clock and SPI data. (See Figure 15-4 and Figure 15-5.) To transmit data between SPI modules, the SPI modules must have identical CPHA bits. When CPHA = 0, the SS pin of the slave SPI module must be set to logic 1 between bytes. (See Figure 15-11). Reset sets the CPHA bit. When CPHA = 0 for a slave, the falling edge of SS indicates the beginning of the transmission. This causes the SPI to leave its idle state and begin driving the MISO pin with the MSB of its data. Once the transmission begins, no new data is allowed into the shift register from the data register. Therefore, the slave data register must be loaded with the desired transmit data before the falling edge of SS. Any data written after the falling edge is stored in the data register and transferred to the shift register at the current transmission. When CPHA = 1 for a slave, the first edge of the SPSCK indicates the beginning of the transmission. The same applies when SS is high for a slave. The MISO pin is held in a high-impedance state, and the incoming SPSCK is ignored. In certain cases, it may also cause the MODF flag to be set. (See 15.6.2 Mode Fault Error). A logic 1 on the SS pin does not in any way affect the state of the SPI state machine. Freescale Semiconductor, Inc... Data Sheet 220 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module I/O Registers SPWOM -- SPI Wired-OR Mode Bit This read/write bit disables the pullup devices on pins SPSCK, MOSI, and MISO so that those pins become open-drain outputs. 1 = Wired-OR SPSCK, MOSI, and MISO pins 0 = Normal push-pull SPSCK, MOSI, and MISO pins SPE -- SPI Enable Bit This read/write bit enables the SPI module. Clearing SPE causes a partial reset of the SPI (see 15.9 Resetting the SPI). Reset clears the SPE bit. 1 = SPI module enabled 0 = SPI module disabled Freescale Semiconductor, Inc... SPTIE -- SPI Transmit Interrupt Enable Bit This read/write bit enables CPU interrupt requests generated by the SPTE bit. SPTE is set when a byte transfers from the transmit data register to the shift register. Reset clears the SPTIE bit. 1 = SPTE CPU interrupt requests enabled 0 = SPTE CPU interrupt requests disabled 15.13.2 SPI Status and Control Register The SPI status and control register contains flags to signal the following conditions: * * * * Receive data register full Failure to clear SPRF bit before next byte is received (overflow error) Inconsistent logic level on SS pin (mode fault error) Transmit data register empty The SPI status and control register also contains bits that perform these functions: * * * Enable error interrupts Enable mode fault error detection Select master SPI baud rate $000E Bit 7 Read: Write: Reset: 0 SPRF 6 ERRIE 0 5 OVRF 4 MODF 3 SPTE 2 MODFEN 0 1 SPR1 0 Bit 0 SPR0 0 Address: 0 0 1 = Unimplemented Figure 15-13. SPI Status and Control Register (SPSCR) SPRF -- SPI Receiver Full Bit This clearable, read-only flag is set each time a byte transfers from the shift register to the receive data register. SPRF generates a CPU interrupt request if the SPRIE bit in the SPI control register is set also. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 221 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module During an SPRF CPU interrupt, the CPU clears SPRF by reading the SPI status and control register with SPRF set and then reading the SPI data register. Any read of the SPI data register clears the SPRF bit. Reset clears the SPRF bit. 1 = Receive data register full 0 = Receive data register not full ERRIE -- Error Interrupt Enable Bit This read-only bit enables the MODF and OVRF flags to generate CPU interrupt requests. Reset clears the ERRIE bit. 1 = MODF and OVRF can generate CPU interrupt requests 0 = MODF and OVRF cannot generate CPU interrupt requests Freescale Semiconductor, Inc... OVRF -- Overflow Bit This clearable, read-only flag is set if software does not read the byte in the receive data register before the next byte enters the shift register. In an overflow condition, the byte already in the receive data register is unaffected, and the byte that shifted in last is lost. Clear the OVRF bit by reading the SPI status and control register with OVRF set and then reading the SPI data register. Reset clears the OVRF flag. 1 = Overflow 0 = No overflow MODF -- Mode Fault Bit This clearable, read-only flag is set in a slave SPI if the SS pin goes high during a transmission. In a master SPI, the MODF flag is set if the SS pin goes low at any time. Clear the MODF bit by reading the SPI status and control register with MODF set and then writing to the SPI data register. Reset clears the MODF bit. 1 = SS pin at inappropriate logic level 0 = SS pin at appropriate logic level SPTE -- SPI Transmitter Empty Bit This clearable, read-only flag is set each time the transmit data register transfers a byte into the shift register. SPTE generates an SPTE CPU interrupt request if the SPTIE bit in the SPI control register is set also. NOTE: Do not write to the SPI data register unless the SPTE bit is high. For an idle master or idle slave that has no data loaded into its transmit buffer, the SPTE will be set again within two bus cycles since the transmit buffer empties into the shift register. This allows the user to queue up a 16-bit value to send. For an already active slave, the load of the shift register cannot occur until the transmission is completed. This implies that a back-to-back write to the transmit data register is not possible. The SPTE indicates when the next write can occur. Reset sets the SPTE bit. 1 = Transmit data register empty 0 = Transmit data register not empty Data Sheet 222 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module I/O Registers MODFEN -- Mode Fault Enable Bit This read/write bit, when set to 1, allows the MODF flag to be set. If the MODF flag is set, clearing the MODFEN does not clear the MODF flag. If the SPI is enabled as a master and the MODFEN bit is low, then the SS pin is available as a general-purpose I/O. If the MODFEN bit is set, then this pin is not available as a general purpose I/O. When the SPI is enabled as a slave, the SS pin is not available as a general-purpose I/O regardless of the value of MODFEN. (See SS (Slave Select) on page 218). If the MODFEN bit is low, the level of the SS pin does not affect the operation of an enabled SPI configured as a master. For an enabled SPI configured as a slave, having MODFEN low only prevents the MODF flag from being set. It does not affect any other part of SPI operation. (See 15.6.2 Mode Fault Error). SPR1 and SPR0 -- SPI Baud Rate Select Bits In master mode, these read/write bits select one of four baud rates as shown in Table 15-6. SPR1 and SPR0 have no effect in slave mode. Reset clears SPR1 and SPR0. Table 15-6. SPI Master Baud Rate Selection SPR1:SPR0 00 01 10 11 Baud Rate Divisor (BD) 2 8 32 128 Freescale Semiconductor, Inc... Use this formula to calculate the SPI baud rate: CGMOUT Baud rate = ------------------------2 x BD where: CGMOUT = base clock output of the internal clock generator module (ICG), see Section 8. Internal Clock Generator (ICG) Module. BD = baud rate divisor MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Serial Peripheral Interface (SPI) Module Data Sheet 223 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Serial Peripheral Interface (SPI) Module 15.13.3 SPI Data Register The SPI data register is the read/write buffer for the receive data register and the transmit data register. Writing to the SPI data register writes data into the transmit data register. Reading the SPI data register reads data from the receive data register. The transmit data and receive data registers are separate buffers that can contain different values. See Figure 15-2 Address: Read: $000F Bit 7 R7 T7 Write: Reset: 6 R6 T6 5 R5 T5 4 R4 T4 3 R3 T3 2 R2 T2 1 R1 T1 Bit 0 R0 T0 Freescale Semiconductor, Inc... Indeterminate after Reset Figure 15-14. SPI Data Register (SPDR) R7-R0/T7-T0 -- Receive/Transmit Data Bits NOTE: Do not use read-modify-write instructions on the SPI data register since the buffer read is not the same as the buffer written. Data Sheet 224 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Serial Peripheral Interface (SPI) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 16. Timebase Module (TBM) 16.1 Introduction This section describes the timebase module (TBM). The TBM will generate periodic interrupts at user selectable rates using a counter clocked by either the internal or external clock sources. This TBM version uses 15 divider stages, eight of which are user selectable. NOTE: The TBM on this device differs from that of the MC68HC908KX8 in that it has an additional divide-by-128 at the front end of the divider chain. For further information regarding timers on M68HC08 family devices, please consult the HC08 Timer Reference Manual, Motorola order number TIM08RM/AD. Freescale Semiconductor, Inc... 16.2 Features Features of the TBM module include: * Software configurable periodic interrupts with divide-by-1024, 2048, 4096, 8192, 16384, 262144, 1048576, and 4194304 taps of the selected clock source * Configurable for operation during stop mode to allow periodic wake up from stop 16.3 Functional Description This module can generate a periodic interrupt by dividing the clock source supplied from the internal clock generator module, TBMCLK. Note that this clock source is the external clock ECLK when the ECGON bit in the ICG control register (ICGCR) is set. Otherwise, TBMCLK is driven at the internally generated clock frequency (ICLK). In other words, if the external clock is enabled it will be used as the TBMCLK, even if the MCU bus clock is based on the internal clock. The counter is initialized to all 0s when TBON bit is cleared. The counter, shown in Figure 16-1, starts counting when the TBON bit is set. When the counter overflows at the tap selected by TBR2-TBR0, the TBIF bit gets set. If the TBIE bit is set, an interrupt request is sent to the CPU. The TBIF flag is cleared by writing a 1 to the TACK bit. The first time the TBIF flag is set after enabling the timebase module, the interrupt is generated at approximately half of the overflow period. Subsequent events occur at the exact period. The timebase module may remain active after execution of the STOP instruction if the internal clock generator has been enabled to operate during stop mode through the OSCENINSTOP bit in the configuration register. The timebase module can be used in this mode to generate a periodic wakeup from stop mode. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timebase Module (TBM) Data Sheet 225 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timebase Module (TBM) TBMCLKSEL FROM CONFIG2 0 TBMCLK FROM ICG MODULE DIVIDE BY 128 PRESCALER 1 TBON Freescale Semiconductor, Inc... /2 /2 /2 /2 /2 /2 /2 TBMINT /2 /2 /2 /2 /2 /2 /2 /2 TACK TBR0 TBR2 TBR1 TBIF 000 001 010 011 100 101 110 111 SEL R TBIE Figure 16-1. Timebase Block Diagram 16.4 Interrupts The timebase module can periodically interrupt the CPU with a rate defined by the selected TBMCLK and the select bits TBR2-TBR0. When the timebase counter chain rolls over, the TBIF flag is set. If the TBIE bit is set, enabling the timebase interrupt, the counter chain overflow will generate a CPU interrupt request. Interrupts must be acknowledged by writing a 1 to the TACK bit. Data Sheet 226 Timebase Module (TBM) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timebase Module (TBM) TBM Interrupt Rate 16.5 TBM Interrupt Rate The interrupt rate is determined by the equation: Divider 1 t TBMRATE = ----------------------- = -------------------f TBMCLK f TBMRATE where: fTBMCLK =Frequency supplied from the internal clock generator (ICG) module Divider = Divider value as determined by TBR2-TBR0 settings. See Table 16-1. As an example, a clock source of 4.9152 MHz and the TBR2-TBR0 set to {011}, the divider tap is 128 and the interrupt rate calculates to 128/4.9152 x 106 = 26 s. Table 16-1. Timebase Divider Selection TBR2(1) 0 0 0 0 1 1 1 1 TBR1 0 0 1 1 0 0 1 1 (1) Freescale Semiconductor, Inc... TBR0(1) 0 0 1 0 1 0 1 0 1 32,768 8192 2048 128 64 32 16 8 Divider Tap TMBCLKSEL 1 4,194,304 1,048,576 262144 16,384 8192 4096 2048 1024 1. Do not change TBR2-TBR0 bits while the timebase is enabled (TBON = 1). 16.6 Low-Power Modes The WAIT and STOP instructions put the MCU in low power-consumption standby modes. 16.6.1 Wait Mode The timebase module remains active after execution of the WAIT instruction. In wait mode the timebase register is not accessible by the CPU. If the timebase functions are not required during wait mode, reduce the power consumption by stopping the timebase before executing the WAIT instruction. 16.6.2 Stop Mode The timebase module may remain active after execution of the STOP instruction if the internal clock generator has been enabled to operate during stop mode through the OSCENINSTOP bit in the configuration register. The timebase module can be used in this mode to generate a periodic wake up from stop mode. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timebase Module (TBM) Data Sheet 227 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timebase Module (TBM) If the internal clock generator has not been enabled to operate in stop mode, the timebase module will not be active during stop mode. In stop mode, the timebase register is not accessible by the CPU. If the timebase functions are not required during stop mode, reduce power consumption by disabling the timebase module before executing the STOP instruction. 16.7 Timebase Control Register The timebase has one register, the timebase control register (TBCR), which is used to enable the timebase interrupts and set the rate. Freescale Semiconductor, Inc... Address: $001C Bit 7 Read: Write: Reset: 0 TBIF 6 TBR2 0 5 TBR1 0 4 TBR0 0 3 0 TACK 0 R 2 TBIE 0 = Reserved 1 TBON 0 Bit 0 R 0 = Unimplemented Figure 16-2. Timebase Control Register (TBCR) TBIF -- Timebase Interrupt Flag This read-only flag bit is set when the timebase counter has rolled over. 1 = Timebase interrupt pending 0 = Timebase interrupt not pending TBR2-TBR0 -- Timebase Divider Selection Bits These read/write bits select the tap in the counter to be used for timebase interrupts as shown in Table 16-1. NOTE: Do not change TBR2-TBR0 bits while the timebase is enabled (TBON = 1). TACK-- Timebase ACKnowledge Bit The TACK bit is a write-only bit and always reads as 0. Writing a 1 to this bit clears TBIF, the timebase interrupt flag bit. Writing a 0 to this bit has no effect. 1 = Clear timebase interrupt flag 0 = No effect TBIE -- Timebase Interrupt Enabled Bit This read/write bit enables the timebase interrupt when the TBIF bit becomes set. Reset clears the TBIE bit. 1 = Timebase interrupt is enabled. 0 = Timebase interrupt is disabled. TBON -- Timebase Enabled Bit This read/write bit enables the timebase. Timebase may be turned off to reduce power consumption when its function is not necessary. The counter can be initialized by clearing and then setting this bit. Reset clears the TBON bit. 1 = Timebase is enabled. 0 = Timebase is disabled and the counter initialized to 0s. NOTE: Data Sheet 228 Timebase Module (TBM) Clearing TBON has no effect on the TBIF flag. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 17. Timer Interface A (TIMA) Module 17.1 Introduction This section describes the timer interface A module (TIMA). The TIMA is a 2-channel timer that provides a timing reference with input capture, output compare, and pulse width modulation (PWM) functions. Figure 17-2 is a block diagram of the TIMA and Figure 17-3 provides a summary of the input/output (I/O) registers. For further information regarding timers on M68HC08 family devices, please consult the HC08 Timer Reference Manual, Motorola document order number TIM08RM/AD. Freescale Semiconductor, Inc... 17.2 Features Features include: * Two input capture/output compare channels - Rising-edge, falling-edge, or any-edge input capture trigger - Set, clear, or toggle output compare action Buffered and unbuffered PWM signal generation Programmable TIMA clock input - 7-frequency internal bus clock prescaler selection Free-running or modulo up-count operation Toggle any channel pin on overflow TIMA counter stop and reset bits * * * * * 17.3 Functional Description Figure 17-2 shows the TIMA structure. The central component of the TIMA is the 16-bit TIMA counter that can operate as a free-running counter or a modulo up-counter. The TIMA counter provides the timing reference for the input capture and output compare functions. The TIMA counter modulo registers, TAMODH-TAMODL, control the modulo value of the TIMA counter. Software can read the TIMA counter value at any time without affecting the counting sequence. The two TIMA channels are programmable independently as input capture or output compare channels. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface A (TIMA) Module Data Sheet 229 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module INTERNAL BUS M68HC08 CPU CPU REGISTERS ARITHMETIC/LOGIC UNIT (ALU) SINGLE BREAKPOINT BREAK MODULE PORT A DDRA 5-BIT KEYBOARD INTERRUPT MODULE PTA6/SS PTA5/SPSCK PTA4/KBD4 PTA3/KBD3 PTA2/KBD2 PTA1/KBD1 2-CHANNEL TIMER INTERFACE MODULE A PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PORT B DDRB PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK PTC1/MOSI PTC0/MISO PTD1/TACH1 PTD0/TACH0 PTE1/RxD PTE0/TxD PORT C PORT E PORT D CONTROL AND STATUS REGISTERS 64 BYTES USER FLASH 15,872 BYTES USER RAM 512 BYTES Freescale Semiconductor, Inc... MONITOR ROM 310 BYTES FLASH PROGRAMMING (BURN-IN) ROM 1024 BYTES USER FLASH VECTOR SPACE 36 BYTES 2-CHANNEL TIMER INTERFACE MODULE B ENHANCED SERIAL COMMUNICATION INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE OSC2 OSC1 INTERNAL CLOCK GENERATOR MODULE SERIAL PERIPHERAL INTERFACE MODULE RST 24 INTERNAL SYSTEM INTEGRATION MODULE SINGLE EXTERNAL IRQ MODULE CONFIGURATION REGISTER MODULE PERIODIC WAKEUP TIMEBASE MODULE ARBITER MODULE PRESCALER MODULE IRQ VREFH VDDA VREFL VSSA VDD VSS DDRE DDRD DDRC 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE SECURITY MODULE POWER BEMF MODULE Figure 17-1. Block Diagram Highlighting TIMA Block and Pins Data Sheet 230 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface A (TIMA) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module Functional Description INTERNAL BUS CLOCK PRESCALER PRESCALER SELECT TSTOP TRST 16-BIT COUNTER PS2 PS1 PS0 TOF TOIE INTERRUPT LOGIC 16-BIT COMPARATOR TAMODH:TAMODL Freescale Semiconductor, Inc... CHANNEL 0 16-BIT COMPARATOR TACH0H:TACH0L 16-BIT LATCH ELS0B ELS0A TOV0 CH0MAX CH0F PTD0 LOGIC INTERRUPT LOGIC PTD0/TACH0 MS0A CHANNEL 1 16-BIT COMPARATOR TACH1H:TACH1L 16-BIT LATCH MS1A ELS1B ELS1A MS0B CH0IE TOV1 CH1MAX PTD1 LOGIC INTERRUPT LOGIC PTD1/TACH1 CH1F CH1IE Figure 17-2. TIMA Block Diagram Addr. $0020 Register Name TIMA Status and Control Read: Register (TASC) Write: See page 239. Reset: TIMA Counter Register High Read: (TACNTH) Write: See page 241. Reset: TIMA Counter Register Low Read: (TACNTL) Write: See page 241. Reset: TIMA Counter Modulo Read: Register High (TAMODH) Write: See page 242. Reset: TIMA Counter Modulo Read: Register Low (TAMODL) Write: See page 242. Reset: Bit 7 TOF 0 0 BIT 15 0 BIT 7 0 BIT 15 1 BIT 7 1 R 6 TOIE 0 BIT 14 0 BIT 6 0 BIT 14 1 BIT 6 1 = Reserved 5 TSTOP 1 BIT 13 0 BIT 5 0 BIT 13 1 BIT 5 1 4 0 TRST 0 BIT 12 0 BIT 4 0 BIT 12 1 BIT 4 1 3 R 0 BIT 11 0 BIT 3 0 BIT 11 1 BIT 3 1 = Unimplemented 2 PS2 0 BIT 10 0 BIT 2 0 BIT 10 1 BIT 2 1 1 PS1 0 BIT 9 0 BIT 1 0 BIT 9 1 BIT 1 1 Bit 0 PS0 0 BIT 8 0 BIT 0 0 BIT 8 1 BIT 0 1 $0021 $0022 $0023 $0024 Figure 17-3. TIMA I/O Register Summary MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface A (TIMA) Module Data Sheet 231 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module Addr. $0025 Register Name TIMA Channel 0 Status and Read: Control Register (TASC0) Write: See page 243. Reset: TIMA Channel 0 Register Read: High (TACH0H) Write: See page 246. Reset: TIMA Channel 0 Register Read: Low (TACH0L) Write: See page 246. Reset: TIMA Channel 1 Status and Read: Control Register (TASC1) Write: See page 243. Reset: TIMA Channel 1 Register Read: High (TACH1H) Write: See page 246. Reset: TIMA Channel 1 Register Read: Low (TACH1L) Write: See page 246. Reset: Bit 7 CH0F 0 0 BIT 15 6 CH0IE 0 BIT 14 5 MS0B 0 BIT 13 4 MS0A 0 BIT 12 3 ELS0B 0 BIT 11 2 ELS0A 0 BIT 10 1 TOV0 0 BIT 9 Bit 0 CH0MAX 0 BIT 8 $0026 Indeterminate after reset BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 $0027 Indeterminate after reset CH1F 0 0 BIT 15 CH1IE 0 BIT 14 0 R 0 BIT 13 MS1A 0 BIT 12 ELS1B 0 BIT 11 ELS1A 0 BIT 10 TOV1 0 BIT 9 CH1MAX 0 BIT 8 Freescale Semiconductor, Inc... $0028 $0029 Indeterminate after reset BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 $002A Indeterminate after reset R = Reserved = Unimplemented Figure 17-3. TIMA I/O Register Summary (Continued) 17.3.1 TIMA Counter Prescaler The TIMA clock source can be one of the seven prescaler outputs. The prescaler generates seven clock rates from the internal bus clock. The prescaler select bits, PS[2:0], in the TIMA status and control register select the TIMA clock source. 17.3.2 Input Capture An input capture function has three basic parts: edge select logic, an input capture latch, and a 16-bit counter. Two 8-bit registers, which make up the 16-bit input capture register, are used to latch the value of the free-running counter after the corresponding input capture edge detector senses a defined transition. The polarity of the active edge is programmable. The level transition which triggers the counter transfer is defined by the corresponding input edge bits (ELSxB and ELSxA in TASC0 through TASC1 control registers with x referring to the active channel number). When an active edge occurs on the pin of an input capture channel, the TIMA latches the contents of the TIMA counter into the TIMA channel registers, TACHxH-TACHxL. Input captures can generate TIMA central processor unit (CPU) interrupt requests. Software can determine that an input capture event has occurred by enabling input capture interrupts or by polling the status flag bit. Data Sheet 232 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface A (TIMA) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module Functional Description The free-running counter contents are transferred to the TIMA channel status and control register (TACHxH-TACHxL, see 17.8.5 TIMA Channel Registers) on each proper signal transition regardless of whether the TIMA channel flag (CH0F-CH1F in TASC0-TASC1 registers) is set or clear. When the status flag is set, a CPU interrupt is generated if enabled. The value of the count latched or "captured" is the time of the event. Because this value is stored in the input capture register 2 bus cycles after the actual event occurs, user software can respond to this event at a later time and determine the actual time of the event. However, this must be done prior to another input capture on the same pin; otherwise, the previous time value will be lost. Freescale Semiconductor, Inc... By recording the times for successive edges on an incoming signal, software can determine the period and/or pulse width of the signal. To measure a period, two successive edges of the same polarity are captured. To measure a pulse width, two alternate polarity edges are captured. Software should track the overflows at the 16-bit module counter to extend its range. Another use for the input capture function is to establish a time reference. In this case, an input capture function is used in conjunction with an output compare function. For example, to activate an output signal a specified number of clock cycles after detecting an input event (edge), use the input capture function to record the time at which the edge occurred. A number corresponding to the desired delay is added to this captured value and stored to an output compare register (see 17.8.5 TIMA Channel Registers). Because both input captures and output compares are referenced to the same 16-bit modulo counter, the delay can be controlled to the resolution of the counter independent of software latencies. Reset does not affect the contents of the input capture channel register (TACHxH-TACHxL). 17.3.3 Output Compare With the output compare function, the TIMA can generate a periodic pulse with a programmable polarity, duration, and frequency. When the counter reaches the value in the registers of an output compare channel, the TIMA can set, clear, or toggle the channel pin. Output compares can generate TIMA CPU interrupt requests. 17.3.3.1 Unbuffered Output Compare Any output compare channel can generate unbuffered output compare pulses as described in 17.3.3 Output Compare. The pulses are unbuffered because changing the output compare value requires writing the new value over the old value currently in the TIMA channel registers. An unsynchronized write to the TIMA channel registers to change an output compare value could cause incorrect operation for up to two counter overflow periods. For example, writing a new value before the counter reaches the old value MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface A (TIMA) Module Data Sheet 233 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module but after the counter reaches the new value prevents any compare during that counter overflow period. Also, using a TIMA overflow interrupt routine to write a new, smaller output compare value may cause the compare to be missed. The TIMA may pass the new value before it is written. Use these methods to synchronize unbuffered changes in the output compare value on channel x: * When changing to a smaller value, enable channel x output compare interrupts and write the new value in the output compare interrupt routine. The output compare interrupt occurs at the end of the current output compare pulse. The interrupt routine has until the end of the counter overflow period to write the new value. When changing to a larger output compare value, enable TIMA overflow interrupts and write the new value in the TIMA overflow interrupt routine. The TIMA overflow interrupt occurs at the end of the current counter overflow period. Writing a larger value in an output compare interrupt routine (at the end of the current pulse) could cause two output compares to occur in the same counter overflow period. Freescale Semiconductor, Inc... * 17.3.3.2 Buffered Output Compare Channels 0 and 1 can be linked to form a buffered output compare channel whose output appears on the PTD0/TACH0 pin. The TIMA channel registers of the linked pair alternately control the output. Setting the MS0B bit in TIMA channel 0 status and control register (TASC0) links channel 0 and channel 1. The output compare value in the TIMA channel 0 registers initially controls the output on the PTD0/TACH0 pin. Writing to the TIMA channel 1 registers enables the TIMA channel 1 registers to synchronously control the output after the TIMA overflows. At each subsequent overflow, the TIMA channel registers (0 or 1) that control the output are the ones written to last. TSC0 controls and monitors the buffered output compare function, and TIMA channel 1 status and control register (TASC1) is unused. While the MS0B bit is set, the channel 1 pin, PTD1/TACH1, is available as a general-purpose I/O pin. NOTE: In buffered output compare operation, do not write new output compare values to the currently active channel registers. User software should track the currently active channel to prevent writing a new value to the active channel. Writing to the active channel registers is the same as generating unbuffered output compares. 17.3.4 Pulse Width Modulation (PWM) By using the toggle-on-overflow feature with an output compare channel, the TIMA can generate a PWM signal. The value in the TIMA counter modulo registers determines the period of the PWM signal. The channel pin toggles when the counter reaches the value in the TIMA counter modulo registers. The time between overflows is the period of the PWM signal. Data Sheet 234 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface A (TIMA) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module Functional Description As Figure 17-4 shows, the output compare value in the TIMA channel registers determines the pulse width of the PWM signal. The time between overflow and output compare is the pulse width. Program the TIMA to clear the channel pin on output compare if the state of the PWM pulse is logic 1. Program the TIMA to set the pin if the state of the PWM pulse is logic 0. OVERFLOW PERIOD OVERFLOW OVERFLOW Freescale Semiconductor, Inc... PULSE WIDTH PTEx/TCHx OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE Figure 17-4. PWM Period and Pulse Width The value in the TIMA counter modulo registers and the selected prescaler output determines the frequency of the PWM output. The frequency of an 8-bit PWM signal is variable in 256 increments. Writing $00FF (255) to the TIMA counter modulo registers produces a PWM period of 256 times the internal bus clock period if the prescaler select value is $000 (see 17.8.1 TIMA Status and Control Register). The value in the TIMA channel registers determines the pulse width of the PWM output. The pulse width of an 8-bit PWM signal is variable in 256 increments. Writing $0080 (128) to the TIMA channel registers produces a duty cycle of 128/256 or 50%. 17.3.4.1 Unbuffered PWM Signal Generation Any output compare channel can generate unbuffered PWM pulses as described in 17.3.4 Pulse Width Modulation (PWM). The pulses are unbuffered because changing the pulse width requires writing the new pulse width value over the value currently in the TIMA channel registers. An unsynchronized write to the TIMA channel registers to change a pulse width value could cause incorrect operation for up to two PWM periods. For example, writing a new value before the counter reaches the old value but after the counter reaches the new value prevents any compare during that PWM period. Also, using a TIMA overflow interrupt routine to write a new, smaller pulse width value may cause the compare to be missed. The TIMA may pass the new value before it is written to the TIMA channel registers. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface A (TIMA) Module Data Sheet 235 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module Use these methods to synchronize unbuffered changes in the PWM pulse width on channel x: * When changing to a shorter pulse width, enable channel x output compare interrupts and write the new value in the output compare interrupt routine. The output compare interrupt occurs at the end of the current pulse. The interrupt routine has until the end of the PWM period to write the new value. When changing to a longer pulse width, enable TIMA overflow interrupts and write the new value in the TIMA overflow interrupt routine. The TIMA overflow interrupt occurs at the end of the current PWM period. Writing a larger value in an output compare interrupt routine (at the end of the current pulse) could cause two output compares to occur in the same PWM period. * Freescale Semiconductor, Inc... NOTE: In PWM signal generation, do not program the PWM channel to toggle on output compare. Toggling on output compare prevents reliable 0% duty cycle generation and removes the ability of the channel to self-correct in the event of software error or noise. Toggling on output compare also can cause incorrect PWM signal generation when changing the PWM pulse width to a new, much larger value. 17.3.4.2 Buffered PWM Signal Generation Channels 0 and 1 can be linked to form a buffered PWM channel whose output appears on the PTD0/TACH0 pin. The TIMA channel registers of the linked pair alternately control the pulse width of the output. Setting the MS0B bit in TIMA channel 0 status and control register (TASC0) links channel 0 and channel 1. The TIMA channel 0 registers initially control the pulse width on the PTD0/TACH0 pin. Writing to the TIMA channel 1 registers enables the TIMA channel 1 registers to synchronously control the pulse width at the beginning of the next PWM period. At each subsequent overflow, the TIMA channel registers (0 or 1) that control the pulse width are the ones written to last. TASC0 controls and monitors the buffered PWM function, and TIMA channel 1 status and control register (TASC1) is unused. While the MS0B bit is set, the channel 1 pin, PTD1/TACH1, is available as a general-purpose I/O pin. NOTE: In buffered PWM signal generation, do not write new pulse width values to the currently active channel registers. User software should track the currently active channel to prevent writing a new value to the active channel. Writing to the active channel registers is the same as generating unbuffered PWM signals. Data Sheet 236 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface A (TIMA) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module Functional Description 17.3.4.3 PWM Initialization To ensure correct operation when generating unbuffered or buffered PWM signals, use this initialization procedure: 1. In the TIMA status and control register (TASC): a. Stop the TIMA counter by setting the TIMA stop bit, TSTOP. b. Reset the TIMA counter prescaler by setting the TIMA reset bit, TRST. 2. In the TIMA counter modulo registers (TAMODH-TAMODL), write the value for the required PWM period. 3. In the TIMA channel x registers (TACHxH-TACHxL), write the value for the required pulse width. 4. In TIMA channel x status and control register (TASCx): a. Write 0:1 (for unbuffered output compare or PWM signals) or 1:0 (for buffered output compare or PWM signals) to the mode select bits, MSxB-MSxA. See Table 17-2. b. Write 1 to the toggle-on-overflow bit, TOVx. c. Write 1:0 (to clear output on compare) or 1:1 (to set output on compare) to the edge/level select bits, ELSxB-ELSxA. The output action on compare must force the output to the complement of the pulse width level. See Table 17-2. NOTE: In PWM signal generation, do not program the PWM channel to toggle on output compare. Toggling on output compare prevents reliable 0% duty cycle generation and removes the ability of the channel to self-correct in the event of software error or noise. Toggling on output compare can also cause incorrect PWM signal generation when changing the PWM pulse width to a new, much larger value. 5. In the TIMA status control register (TASC), clear the TIMA stop bit, TSTOP. Setting MS0B links channels 0 and 1 and configures them for buffered PWM operation. The TIMA channel 0 registers (TACH0H-TACH0L) initially control the buffered PWM output. TIMA status control register 0 (TASC0) controls and monitors the PWM signal from the linked channels. MS0B takes priority over MS0A. Clearing the toggle-on-overflow bit, TOVx, inhibits output toggles on TIMA overflows. Subsequent output compares try to force the output to a state it is already in and have no effect. The result is a 0% duty cycle output. Setting the channel x maximum duty cycle bit (CHxMAX) and setting the TOVx bit generates a 100% duty cycle output. See 17.8.4 TIMA Channel Status and Control Registers. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface A (TIMA) Module Data Sheet 237 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module 17.4 Interrupts These TIMA sources can generate interrupt requests: * TIMA overflow flag (TOF) -- The TOF bit is set when the TIM counter reaches the modulo value programmed in the TIMA counter modulo registers. The TIMA overflow interrupt enable bit, TOIE, enables TIMA overflow CPU interrupt requests. TOF and TOIE are in the TIMA status and control register. TIMA channel flags (CH1F-CH0F) -- The CHxF bit is set when an input capture or output compare occurs on channel x. Channel x TIMA CPU interrupt requests are controlled by the channel x interrupt enable bit, CHxIE. * Freescale Semiconductor, Inc... 17.5 Low-Power Modes The WAIT and STOP instructions put the microcontroller unit (MCU) in low power-consumption standby modes. 17.5.1 Wait Mode The TIMA remains active after the execution of a WAIT instruction. In wait mode, the TIMA registers are not accessible by the CPU. Any enabled CPU interrupt request from the TIMA can bring the MCU out of wait mode. If TIMA functions are not required during wait mode, reduce power consumption by stopping the TIMA before executing the WAIT instruction. 17.5.2 Stop Mode The TIMA is inactive after the execution of a STOP instruction. The STOP instruction does not affect register conditions or the state of the TIMA counter. TIMA operation resumes when the MCU exits stop mode. 17.6 TIMA During Break Interrupts A break interrupt stops the TIMA counter and inhibits input captures. The system integration module (SIM) controls whether status bits in other modules can be cleared during the break state. The BCFE bit in the SIM break flag control register (SBFCR) enables software to clear status bits during the break state. To allow software to clear status bits during a break interrupt, write a 1 to the BCFE bit. If a status bit is cleared during the break state, it remains cleared when the MCU exits the break state. To protect status bits during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default state), software can read and write I/O registers during the break state without affecting status bits. Some status bits have a 2-step read/write Data Sheet 238 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface A (TIMA) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module I/O Signals clearing procedure. If software does the first step on such a bit before the break, the bit cannot change during the break state as long as BCFE is at 0. After the break, doing the second step clears the status bit. 17.7 I/O Signals Port D shares two of its pins with the TIMA. There is no external clock input to the TIMA prescaler. The two TIMA channel I/O pins are PTD0/TACH0 and PTD1/TACH1. Each channel I/O pin is programmable independently as an input capture pin or an output compare pin. PTD0/TACH0 and PTD1/TACH1 can be configured as buffered output compare or buffered PWM pins. Freescale Semiconductor, Inc... 17.8 I/O Registers These I/O registers control and monitor TIMA operation: * * * * * TIMA status and control register, TASC TIMA control registers, TACNTH-TACNTL TIMA counter modulo registers, TAMODH-TAMODL TIMA channel status and control registers, TASC0 and TASC1 TIMA channel registers, TACH0H-TACH0L and TACH1H-TACH1L 17.8.1 TIMA Status and Control Register The TIMA status and control register (TASC): * * * * * Enables TIMA overflow interrupts Flags TIMA overflows Stops the TIMA counter Resets the TIMA counter Prescales the TIMA counter clock $$0020 Bit 7 Read: Write: Reset: TOF 0 0 R 6 TOIE 0 = Reserved 5 TSTOP 1 4 0 TRST 0 3 R 0 2 PS2 0 1 PS1 0 Bit 0 PS0 0 Address: Figure 17-5. TIMA Status and Control Register (TASC) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface A (TIMA) Module Data Sheet 239 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module TOF -- TIMA Overflow Flag Bit This read/write flag is set when the TIMA counter reaches the modulo value programmed in the TIMA counter modulo registers. Clear TOF by reading the TIMA status and control register when TOF is set and then writing a 0 to TOF. If another TIMA overflow occurs before the clearing sequence is complete, then writing 0 to TOF has no effect. Therefore, a TOF interrupt request cannot be lost due to inadvertent clearing of TOF. Reset clears the TOF bit. Writing a 1 to TOF has no effect. 1 = TIMA counter has reached modulo value 0 = TIMA counter has not reached modulo value Freescale Semiconductor, Inc... TOIE -- TIMA Overflow Interrupt Enable Bit This read/write bit enables TIMA overflow interrupts when the TOF bit becomes set. Reset clears the TOIE bit. 1 = TIMA overflow interrupts enabled 0 = TIMA overflow interrupts disabled TSTOP -- TIMA Stop Bit This read/write bit stops the TIMA counter. Counting resumes when TSTOP is cleared. Reset sets the TSTOP bit, stopping the TIMA counter until software clears the TSTOP bit. 1 = TIMA counter stopped 0 = TIMA counter active NOTE: Do not set the TSTOP bit before entering wait mode if the TIMA is required to exit wait mode. Also, when the TSTOP bit is set and the timer is configured for input capture operation, input captures are inhibited until TSTOP is cleared. TRST -- TIMA Reset Bit Setting this write-only bit resets the TIMA counter and the TIMA prescaler. Setting TRST has no effect on any other registers. Counting resumes from $0000. TRST is cleared automatically after the TIMA counter is reset and always reads as 0. Reset clears the TRST bit. 1 = Prescaler and TIMA counter cleared 0 = No effect NOTE: Setting the TSTOP and TRST bits simultaneously stops the TIMA counter at a value of $0000. PS[2:0] -- Prescaler Select Bits These read/write bits select one of the seven prescaler outputs as the input to the TIMA counter as Table 17-1 shows. Reset clears the PS[2:0] bits. Data Sheet 240 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface A (TIMA) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module I/O Registers Table 17-1. Prescaler Selection PS[2:0] 000 001 010 011 100 101 110 111 TIMA Clock Source Internal bus clock / 1 Internal bus clock / 2 Internal bus clock / 4 Internal bus clock / 8 Internal bus clock / 16 Internal bus clock / 32 Internal bus clock / 64 Unused Freescale Semiconductor, Inc... 17.8.2 TIMA Counter Registers The two read-only TIMA counter registers contain the high and low bytes of the value in the TIMA counter. Reading the high byte (TACNTH) latches the contents of the low byte (TACNTL) into a buffer. Subsequent reads of TACNTH do not affect the latched TACNTL value until TACNTL is read. Reset clears the TIMA counter registers. Setting the TIMA reset bit (TRST) also clears the TIMA counter registers. NOTE: If TACNTH is read during a break interrupt, be sure to unlatch TACNTL by reading TACNTL before exiting the break interrupt. Otherwise, TACNTL retains the value latched during the break. Register Name and Address Bit 7 Read: Write: Reset: BIT 15 R 0 6 BIT 14 R 0 TACNTH -- $0021 5 BIT 13 R 0 4 BIT 12 R 0 3 BIT 11 R 0 2 BIT 10 R 0 1 BIT 9 R 0 Bit 0 BIT 8 R 0 Register Name and Address Bit 7 Read: Write: Reset: BIT 7 R 0 R 6 BIT 6 R 0 = Reserved TACNTL -- $0022 5 BIT 5 R 0 4 BIT 4 R 0 3 BIT 3 R 0 2 BIT 2 R 0 1 BIT 1 R 0 Bit 0 BIT 0 R 0 Figure 17-6. TIMA Counter Registers (TACNTH and TACNTL) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface A (TIMA) Module Data Sheet 241 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module 17.8.3 TIMA Counter Modulo Registers The read/write TIMA modulo registers contain the modulo value for the TIMA counter. When the TIMA counter reaches the modulo value, the overflow flag (TOF) becomes set, and the TIMA counter resumes counting from $0000 at the next timer clock. Writing to the high byte (TMODH) inhibits the TOF bit and overflow interrupts until the low byte (TMODL) is written. Reset sets the TIMA counter modulo registers. Register Name and Address Bit 7 6 BIT 14 1 Read: Write: Reset: TAMODH -- $0023 5 BIT 13 1 4 BIT 12 1 3 BIT 11 1 2 BIT 10 1 1 BIT 9 1 Bit 0 BIT 8 1 Freescale Semiconductor, Inc... BIT 15 1 Register Name and Address Bit 7 Read: Write: Reset: BIT 7 1 6 BIT 6 1 TAMODL -- $0024 5 BIT 5 1 4 BIT 4 1 3 BIT 3 1 2 BIT 2 1 1 BIT 1 1 Bit 0 BIT 0 1 Figure 17-7. TIMA Counter Modulo Registers (TMODH and TMODL) NOTE: Reset the TIMA counter before writing to the TIMA counter modulo registers. 17.8.4 TIMA Channel Status and Control Registers Each of the TIMA channel status and control registers: * * * * * * * * Flags input captures and output compares Enables input capture and output compare interrupts Selects input capture, output compare, or PWM operation Selects high, low, or toggling output on output compare Selects rising edge, falling edge, or any edge as the active input capture trigger Selects output toggling on TIMA overflow Selects 0% and 100% PWM duty cycle Selects buffered or unbuffered output compare/PWM operation Data Sheet 242 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface A (TIMA) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module I/O Registers Register Name and Address Bit 7 Read: Write: Reset: CH0F 0 0 6 CH0IE 0 TASC0 -- $0025 5 MS0B 0 TASC1 -- $0028 6 CH1IE 0 5 0 R 0 4 MS1A 0 3 ELS1B 0 2 ELS1A 0 1 TOV1 0 Bit 0 CH1MAX 0 4 MS0A 0 3 ELS0B 0 2 ELS0A 0 1 TOV0 0 Bit 0 CH0MAX 0 Register Name and Address Bit 7 Read: Write: CH1F 0 0 R Freescale Semiconductor, Inc... Reset: R = Reserved Figure 17-8. TIMA Channel Status and Control Register (TASC0-TASC1) CHxF -- Channel x Flag Bit When channel x is an input capture channel, this read/write bit is set when an active edge occurs on the channel x pin. When channel x is an output compare channel, CHxF is set when the value in the TIMA counter registers matches the value in the TIMA channel x registers. When CHxIE = 1, clear CHxF by reading TIMA channel x status and control register with CHxF set, and then writing a 0 to CHxF. If another interrupt request occurs before the clearing sequence is complete, then writing 0 to CHxF has no effect. Therefore, an interrupt request cannot be lost due to inadvertent clearing of CHxF. Reset clears the CHxF bit. Writing a 1 to CHxF has no effect. 1 = Input capture or output compare on channel x 0 = No input capture or output compare on channel x CHxIE -- Channel x Interrupt Enable Bit This read/write bit enables TIMA CPU interrupts on channel x. Reset clears the CHxIE bit. 1 = Channel x CPU interrupt requests enabled 0 = Channel x CPU interrupt requests disabled MSxB -- Mode Select Bit B This read/write bit selects buffered output compare/PWM operation. MSxB exists only in the TIMA channel 0. Setting MS0B disables the channel 1 status and control register and reverts TACH1 to general-purpose I/O. Reset clears the MSxB bit. 1 = Buffered output compare/PWM operation enabled 0 = Buffered output compare/PWM operation disabled MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface A (TIMA) Module Data Sheet 243 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module MSxA -- Mode Select Bit A When ELSxB:A 00, this read/write bit selects either input capture operation or unbuffered output compare/PWM operation. See Table 17-2. 1 = Unbuffered output compare/PWM operation 0 = Input capture operation When ELSxB:A = 00, this read/write bit selects the initial output level of the TCHx pin once PWM, input capture, or output compare operation is enabled (see Table 17-2). Reset clears the MSxA bit. 1 = Initial output level low 0 = Initial output level high Freescale Semiconductor, Inc... Table 17-2. Mode, Edge, and Level Selection MSxB X X 0 0 0 0 0 0 0 1 1 1 MSxA 0 1 0 0 0 1 1 1 1 X X X ELSxB 0 0 0 1 1 0 0 1 1 0 1 1 ELSxA 0 Output preset 0 1 0 1 0 1 0 1 1 0 1 Buffered output compare or buffered PWM Output compare or PWM Input capture Mode Configuration Pin under port control; initial output level high Pin under port control; initial output level low Capture on rising edge only Capture on falling edge only Capture on rising or falling edge Software compare only Toggle output on compare Clear output on compare Set output on compare Toggle output on compare Clear output on compare Set output on compare NOTE: Before changing a channel function by writing to the MSxB or MSxA bit, set the TSTOP and TRST bits in the TIMA status and control register (TASC). ELSxB and ELSxA -- Edge/Level Select Bits When channel x is an input capture channel, these read/write bits control the active edge-sensing logic on channel x. When channel x is an output compare channel, ELSxB and ELSxA control the channel x output behavior when an output compare occurs. When ELSxB and ELSxA are both clear, channel x is not connected to port D, and pin PTD0/TACH0 or pin PTD1/TACH1 is available as a general-purpose I/O pin. However, channel x is at a state determined by these bits and becomes transparent to the respective pin when PWM, input capture, or output compare mode is enabled. Table 17-2 shows how ELSxB and ELSxA work. Reset clears the ELSxB and ELSxA bits. Data Sheet 244 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface A (TIMA) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module I/O Registers NOTE: Before enabling a TIMA channel register for input capture operation, make sure that the PTDx/TACHx pin is stable for at least two bus clocks. TOVx -- Toggle-On-Overflow Bit When channel x is an output compare channel, this read/write bit controls the behavior of the channel x output when the TIMA counter overflows. When channel x is an input capture channel, TOVx has no effect. Reset clears the TOVx bit. 1 = Channel x pin toggles on TIMA counter overflow. 0 = Channel x pin does not toggle on TIMA counter overflow. NOTE: Freescale Semiconductor, Inc... When TOVx is set, a TIMA counter overflow takes precedence over a channel x output compare if both occur at the same time. CHxMAX -- Channel x Maximum Duty Cycle Bit When the TOVx bit is at 1 and clear output on compare is selected, setting the CHxMAX bit forces the duty cycle of buffered and unbuffered PWM signals to 100 percent. As Figure 17-9 shows, the CHxMAX bit takes effect in the cycle after it is set or cleared. The output stays at 100 percent duty cycle level until the cycle after CHxMAX is cleared. NOTE: The PWM 100 percent duty cycle is defined as output high all of the time. To generate the 100 percent duty cycle, use the CHxMAX bit in the TSCx register. The PWM 0 percent duty cycle is defined as output low all of the time. To generate the 0 percent duty cycle, select clear output on compare and then clear the TOVx bit (CHxMAX = 0). OVERFLOW OVERFLOW OVERFLOW OVERFLOW OVERFLOW PERIOD PTEx/TCHx TOV = 1 OUTPUT COMPARE CHxMAX OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE TOV = 0 Figure 17-9. CHxMAX Latency MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface A (TIMA) Module Data Sheet 245 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface A (TIMA) Module 17.8.5 TIMA Channel Registers These read/write registers contain the captured TIMA counter value of the input capture function or the output compare value of the output compare function. The state of the TIMA channel registers after reset is unknown. In input capture mode (MSxB-MSxA = 0:0), reading the high byte of the TIMA channel x registers (TACHxH) inhibits input captures until the low byte (TACHxL) is read. In output compare mode (MSxB-MSxA 0:0), writing to the high byte of the TIMA channel x registers (TACHxH) inhibits output compares and the CHxF bit until the low byte (TACHxL) is written. Register Name and Address Bit 7 Read: Write: Reset: Register Name and Address Bit 7 Read: Write: Reset: Register Name and Address Bit 7 Read: Write: Reset: Register Name and Address Bit 7 Read: Write: Reset: BIT 7 6 BIT 6 BIT 15 6 BIT 14 BIT 7 6 BIT 6 BIT 15 6 BIT 14 TACH0H -- $0026 5 BIT 13 4 BIT 12 3 BIT 11 2 BIT 10 1 BIT 9 Bit 0 BIT 8 Freescale Semiconductor, Inc... Indeterminate after reset TACH0L -- $0027 5 BIT 5 4 BIT 4 3 BIT 3 2 BIT 2 1 BIT 1 Bit 0 BIT 0 Indeterminate after reset TACH1H -- $0029 5 BIT 13 4 BIT 12 3 BIT 11 2 BIT 10 1 BIT 9 Bit 0 BIT 8 Indeterminate after reset TACH1L -- $002A 5 BIT 5 4 BIT 4 3 BIT 3 2 BIT 2 1 BIT 1 Bit 0 BIT 0 Indeterminate after reset Figure 17-10. TIMA Channel Registers (TACH0H/L-TACH1H/L) Data Sheet 246 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface A (TIMA) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 18. Timer Interface B (TIMB) Module 18.1 Introduction This section describes the timer interface B module (TIMB). The TIMB is a 2-channel timer that provides a timing reference with input capture, output compare, and pulse width modulation (PWM) functions. Figure 18-2 is a block diagram of the TIMB and Figure 18-3 provides a summary of the input/output (I/O) registers. For further information regarding timers on M68HC08 family devices, please consult the HC08 Timer Reference Manual, Motorola document order number TIM08RM/AD. Freescale Semiconductor, Inc... 18.2 Features Features include: * Two input capture/output compare channels - Rising-edge, falling-edge, or any-edge input capture trigger - Set, clear, or toggle output compare action Buffered and unbuffered PWM signal generation Programmable TIMB clock input - 7-frequency internal bus clock prescaler selection Free-running or modulo up-count operation Toggle any channel pin on overflow TIMB counter stop and reset bits * * * * * MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface B (TIMB) Module Data Sheet 247 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module INTERNAL BUS M68HC08 CPU CPU REGISTERS ARITHMETIC/LOGIC UNIT (ALU) SINGLE BREAKPOINT BREAK MODULE PORT A DDRA 5-BIT KEYBOARD INTERRUPT MODULE PTA6/SS PTA5/SPSCK PTA4/KBD4 PTA3/KBD3 PTA2/KBD2 PTA1/KBD1 2-CHANNEL TIMER INTERFACE MODULE A PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PORT B DDRB PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK PTC1/MOSI PTC0/MISO PTD1/TACH1 PTD0/TACH0 PTE1/RxD PTE0/TxD PORT C PORT E PORT D CONTROL AND STATUS REGISTERS 64 BYTES USER FLASH 15,872 BYTES USER RAM 512 BYTES Freescale Semiconductor, Inc... MONITOR ROM 310 BYTES FLASH PROGRAMMING (BURN-IN) ROM 1024 BYTES USER FLASH VECTOR SPACE 36 BYTES 2-CHANNEL TIMER INTERFACE MODULE B ENHANCED SERIAL COMMUNICATION INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE OSC2 OSC1 INTERNAL CLOCK GENERATOR MODULE SERIAL PERIPHERAL INTERFACE MODULE RST 24 INTERNAL SYSTEM INTEGRATION MODULE SINGLE EXTERNAL IRQ MODULE CONFIGURATION REGISTER MODULE PERIODIC WAKEUP TIMEBASE MODULE ARBITER MODULE PRESCALER MODULE IRQ VREFH VDDA VREFL VSSA VDD VSS DDRE DDRD DDRC 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE SECURITY MODULE POWER BEMF MODULE Figure 18-1. Block Diagram Highlighting TIMB Block and Pins Data Sheet 248 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface B (TIMB) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module Features INTERNAL BUS CLOCK PRESCALER PRESCALER SELECT TSTOP TRST 16-BIT COUNTER PS2 PS1 PS0 TOF TOIE INTERRUPT LOGIC 16-BIT COMPARATOR TBMODH:TBMODL Freescale Semiconductor, Inc... CHANNEL 0 16-BIT COMPARATOR TBCH0H:TBCH0L 16-BIT LATCH ELS0B ELS0A TOV0 CH0MAX CH0F PTB6 LOGIC INTERRUPT LOGIC PTB6/TBCH0 MS0A CHANNEL 1 16-BIT COMPARATOR TBCH1H:TBCH1L 16-BIT LATCH MS1A ELS1B ELS1A MS0B CH0IE TOV1 CH1MAX PTB7 LOGIC INTERRUPT LOGIC PTB7/TBCH1 CH1F CH1IE Figure 18-2. TIMB Block Diagram Addr. $002B Register Name TIMB Status and Control Register (TBSC) Write: See page 257. Reset: Read: Bit 7 TOF 0 0 BIT 15 0 BIT 7 0 BIT 15 1 BIT 7 1 R 6 TOIE 0 BIT 14 0 BIT 6 0 BIT 14 1 BIT 6 1 = Reserved 5 TSTOP 1 BIT 13 0 BIT 5 0 BIT 13 1 BIT 5 1 4 0 TRST 0 BIT 12 0 BIT 4 0 BIT 12 1 BIT 4 1 3 0 R 0 BIT 11 0 BIT 3 0 BIT 11 1 BIT 3 1 = Unimplemented 2 PS2 0 BIT 10 0 BIT 2 0 BIT 10 1 BIT 2 1 1 PS1 0 BIT 9 0 BIT 1 0 BIT 9 1 BIT 1 1 Bit 0 PS0 0 BIT 8 0 BIT 0 0 BIT 8 1 BIT 0 1 $002C TIMB Counter Register High Read: (TBCNTH) Write: See page 259. Reset: TIMB Counter Register Low Read: (TBCNTL) Write: See page 259. Reset: TIMB Counter Modulo Read: Register High (TBMODH) Write: See page 260. Reset: TIMB Counter Modulo Register Low (TBMODL) Write: See page 260. Reset: Read: $002D $002E $002F Figure 18-3. TIMB I/O Register Summary MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface B (TIMB) Module Data Sheet 249 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module Addr. $0030 Register Name TIMB Channel 0 Status and Read: Control Register (TBSC0) Write: See page 261. Reset: TIMB Channel 0 Register Read: High (TBCH0H) Write: See page 264. Reset: TIMB Channel 0 Register Read: Low (TBCH0L) Write: See page 264. Reset: TIMB Channel 1 Status and Read: Control Register (TBSC1) Write: See page 261. Reset: TIMB Channel 1 Register High (TBCH1H) Write: See page 264. Reset: Read: Bit 7 CH0F 0 0 BIT 15 6 CH0IE 0 BIT 14 5 MS0B 0 BIT 13 4 MS0A 0 BIT 12 3 ELS0B 0 BIT 11 2 ELS0A 0 BIT 10 1 TOV0 0 BIT 9 Bit 0 CH0MAX 0 BIT 8 $0031 Indeterminate after reset BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 $0032 Indeterminate after reset CH1F 0 0 BIT 15 CH1IE 0 BIT 14 0 R 0 BIT 13 MS1A 0 BIT 12 ELS1B 0 BIT 11 ELS1A 0 BIT 10 TOV1 0 BIT 9 CH1MAX 0 BIT 8 Freescale Semiconductor, Inc... $0033 $0034 Indeterminate after reset BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 $0035 TIMB Channel 1 Register Read: Low (TBCH1L) Write: See page 264. Reset: Indeterminate after reset R = Reserved = Unimplemented Figure 18-3. TIMB I/O Register Summary (Continued) 18.3 Functional Description Figure 18-2 shows the TIMB structure. The central component of the TIMB is the 16-bit TIMB counter that can operate as a free-running counter or a modulo up-counter. The TIMB counter provides the timing reference for the input capture and output compare functions. The TIMB counter modulo registers, TBMODH-TBMODL, control the modulo value of the TIMB counter. Software can read the TIMB counter value at any time without affecting the counting sequence. The two TIMB channels are programmable independently as input capture or output compare channels. 18.3.1 TIMB Counter Prescaler The TIMB clock source can be one of the seven prescaler outputs. The prescaler generates seven clock rates from the internal bus clock. The prescaler select bits, PS[2:0], in the TIMB status and control register select the TIMB clock source. 18.3.2 Input Capture An input capture function has three basic parts: edge select logic, an input capture latch, and a 16-bit counter. Two 8-bit registers, which make up the 16-bit input Data Sheet 250 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface B (TIMB) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module Functional Description capture register, are used to latch the value of the free-running counter after the corresponding input capture edge detector senses a defined transition. The polarity of the active edge is programmable. The level transition which triggers the counter transfer is defined by the corresponding input edge bits (ELSxB and ELSxA in TBSC0 through TBSC1 control registers with x referring to the active channel number). When an active edge occurs on the pin of an input capture channel, the TIMB latches the contents of the TIMB counter into the TIMB channel registers, TCHxH-TCHxL. Input captures can generate TIMB CPU interrupt requests. Software can determine that an input capture event has occurred by enabling input capture interrupts or by polling the status flag bit. Freescale Semiconductor, Inc... The free-running counter contents are transferred to the TIMB channel status and control register (TBCHxH-TBCHxL, see 18.8.5 TIMB Channel Registers) on each proper signal transition regardless of whether the TIMB channel flag (CH0F-CH1F in TBSC0-TBSC1 registers) is set or clear. When the status flag is set, a CPU interrupt is generated if enabled. The value of the count latched or "captured" is the time of the event. Because this value is stored in the input capture register 2 bus cycles after the actual event occurs, user software can respond to this event at a later time and determine the actual time of the event. However, this must be done prior to another input capture on the same pin; otherwise, the previous time value will be lost. By recording the times for successive edges on an incoming signal, software can determine the period and/or pulse width of the signal. To measure a period, two successive edges of the same polarity are captured. To measure a pulse width, two alternate polarity edges are captured. Software should track the overflows at the 16-bit module counter to extend its range. Another use for the input capture function is to establish a time reference. In this case, an input capture function is used in conjunction with an output compare function. For example, to activate an output signal a specified number of clock cycles after detecting an input event (edge), use the input capture function to record the time at which the edge occurred. A number corresponding to the desired delay is added to this captured value and stored to an output compare register (see 18.8.5 TIMB Channel Registers). Because both input captures and output compares are referenced to the same 16-bit modulo counter, the delay can be controlled to the resolution of the counter independent of software latencies. Reset does not affect the contents of the input capture channel register (TBCHxH-TBCHxL). 18.3.3 Output Compare With the output compare function, the TIMB can generate a periodic pulse with a programmable polarity, duration, and frequency. When the counter reaches the value in the registers of an output compare channel, the TIMB can set, clear, or toggle the channel pin. Output compares can generate TIMB CPU interrupt requests. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface B (TIMB) Module Data Sheet 251 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module 18.3.3.1 Unbuffered Output Compare Any output compare channel can generate unbuffered output compare pulses as described in 18.3.3 Output Compare. The pulses are unbuffered because changing the output compare value requires writing the new value over the old value currently in the TIMB channel registers. An unsynchronized write to the TIMB channel registers to change an output compare value could cause incorrect operation for up to two counter overflow periods. For example, writing a new value before the counter reaches the old value but after the counter reaches the new value prevents any compare during that counter overflow period. Also, using a TIMB overflow interrupt routine to write a new, smaller output compare value may cause the compare to be missed. The TIMB may pass the new value before it is written. Use these methods to synchronize unbuffered changes in the output compare value on channel x: * When changing to a smaller value, enable channel x output compare interrupts and write the new value in the output compare interrupt routine. The output compare interrupt occurs at the end of the current output compare pulse. The interrupt routine has until the end of the counter overflow period to write the new value. When changing to a larger output compare value, enable TIMB overflow interrupts and write the new value in the TIMB overflow interrupt routine. The TIMB overflow interrupt occurs at the end of the current counter overflow period. Writing a larger value in an output compare interrupt routine (at the end of the current pulse) could cause two output compares to occur in the same counter overflow period. Freescale Semiconductor, Inc... * 18.3.3.2 Buffered Output Compare Channels 0 and 1 can be linked to form a buffered output compare channel whose output appears on the PTB6/TBCH0 pin. The TIMB channel registers of the linked pair alternately control the output. Setting the MS0B bit in TIMB channel 0 status and control register (TBSC0) links channel 0 and channel 1. The output compare value in the TIMB channel 0 registers initially controls the output on the PTB6/TBCH0 pin. Writing to the TIMB channel 1 registers enables the TIMB channel 1 registers to synchronously control the output after the TIMB overflows. At each subsequent overflow, the TIMB channel registers (0 or 1) that control the output are the ones written to last. TSC0 controls and monitors the buffered output compare function, and TIMB channel 1 status and control register (TBSC1) is unused. While the MS0B bit is set, the channel 1 pin, PTB7/TBCH1, is available as a general-purpose I/O pin. NOTE: In buffered output compare operation, do not write new output compare values to the currently active channel registers. User software should track the currently Data Sheet 252 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface B (TIMB) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module Functional Description active channel to prevent writing a new value to the active channel. Writing to the active channel registers is the same as generating unbuffered output compares. 18.3.4 Pulse Width Modulation (PWM) By using the toggle-on-overflow feature with an output compare channel, the TIMB can generate a PWM signal. The value in the TIMB counter modulo registers determines the period of the PWM signal. The channel pin toggles when the counter reaches the value in the TIMB counter modulo registers. The time between overflows is the period of the PWM signal. Freescale Semiconductor, Inc... As Figure 18-4 shows, the output compare value in the TIMB channel registers determines the pulse width of the PWM signal. The time between overflow and output compare is the pulse width. Program the TIMB to clear the channel pin on output compare if the state of the PWM pulse is logic 1. Program the TIMB to set the pin if the state of the PWM pulse is logic 0. OVERFLOW PERIOD PULSE WIDTH PTEx/TCHx OVERFLOW OVERFLOW OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE Figure 18-4. PWM Period and Pulse Width The value in the TIMB counter modulo registers and the selected prescaler output determines the frequency of the PWM output. The frequency of an 8-bit PWM signal is variable in 256 increments. Writing $00FF (255) to the TIMB counter modulo registers produces a PWM period of 256 times the internal bus clock period if the prescaler select value is $000 (see 18.8.1 TIMB Status and Control Register). The value in the TIMB channel registers determines the pulse width of the PWM output. The pulse width of an 8-bit PWM signal is variable in 256 increments. Writing $0080 (128) to the TIMB channel registers produces a duty cycle of 128/256 or 50%. 18.3.4.1 Unbuffered PWM Signal Generation Any output compare channel can generate unbuffered PWM pulses as described in 18.3.4 Pulse Width Modulation (PWM). The pulses are unbuffered because changing the pulse width requires writing the new pulse width value over the value currently in the TIMB channel registers. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface B (TIMB) Module Data Sheet 253 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module An unsynchronized write to the TIMB channel registers to change a pulse width value could cause incorrect operation for up to two PWM periods. For example, writing a new value before the counter reaches the old value but after the counter reaches the new value prevents any compare during that PWM period. Also, using a TIMB overflow interrupt routine to write a new, smaller pulse width value may cause the compare to be missed. The TIMB may pass the new value before it is written to the TIMB channel registers. Use these methods to synchronize unbuffered changes in the PWM pulse width on channel x: * When changing to a shorter pulse width, enable channel x output compare interrupts and write the new value in the output compare interrupt routine. The output compare interrupt occurs at the end of the current pulse. The interrupt routine has until the end of the PWM period to write the new value. When changing to a longer pulse width, enable TIMB overflow interrupts and write the new value in the TIMB overflow interrupt routine. The TIMB overflow interrupt occurs at the end of the current PWM period. Writing a larger value in an output compare interrupt routine (at the end of the current pulse) could cause two output compares to occur in the same PWM period. Freescale Semiconductor, Inc... * NOTE: In PWM signal generation, do not program the PWM channel to toggle on output compare. Toggling on output compare prevents reliable 0% duty cycle generation and removes the ability of the channel to self-correct in the event of software error or noise. Toggling on output compare also can cause incorrect PWM signal generation when changing the PWM pulse width to a new, much larger value. 18.3.4.2 Buffered PWM Signal Generation Channels 0 and 1 can be linked to form a buffered PWM channel whose output appears on the PTB6/TBCH0 pin. The TIMB channel registers of the linked pair alternately control the pulse width of the output. Setting the MS0B bit in TIMB channel 0 status and control register (TBSC0) links channel 0 and channel 1. The TIMB channel 0 registers initially control the pulse width on the PTB6/TBCH0 pin. Writing to the TIMB channel 1 registers enables the TIMB channel 1 registers to synchronously control the pulse width at the beginning of the next PWM period. At each subsequent overflow, the TIMB channel registers (0 or 1) that control the pulse width are the ones written to last. TBSC0 controls and monitors the buffered PWM function, and TIMB channel 1 status and control register (TBSC1) is unused. While the MS0B bit is set, the channel 1 pin, PTB7/TBCH1, is available as a general-purpose I/O pin. NOTE: In buffered PWM signal generation, do not write new pulse width values to the currently active channel registers. User software should track the currently active channel to prevent writing a new value to the active channel. Writing to the active channel registers is the same as generating unbuffered PWM signals. Data Sheet 254 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface B (TIMB) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module Functional Description 18.3.4.3 PWM Initialization To ensure correct operation when generating unbuffered or buffered PWM signals, use this initialization procedure: 1. In the TIMB status and control register (TBSC): a. Stop the TIMB counter by setting the TIMB stop bit, TSTOP. b. Reset the TIMB counter prescaler by setting the TIMB reset bit, TRST. 2. In the TIMB counter modulo registers (TBMODH-TBMODL), write the value for the required PWM period. 3. In the TIMB channel x registers (TBCHxH-TBCHxL), write the value for the required pulse width. 4. In TIMB channel x status and control register (TBSCx): a. Write 0:1 (for unbuffered output compare or PWM signals) or 1:0 (for buffered output compare or PWM signals) to the mode select bits, MSxB-MSxA. See Table 18-2. b. Write 1 to the toggle-on-overflow bit, TOVx. c. Write 1:0 (to clear output on compare) or 1:1 (to set output on compare) to the edge/level select bits, ELSxB-ELSxA. The output action on compare must force the output to the complement of the pulse width level. See Table 18-2. NOTE: In PWM signal generation, do not program the PWM channel to toggle on output compare. Toggling on output compare prevents reliable 0% duty cycle generation and removes the ability of the channel to self-correct in the event of software error or noise. Toggling on output compare can also cause incorrect PWM signal generation when changing the PWM pulse width to a new, much larger value. 5. In the TIMB status control register (TBSC), clear the TIMB stop bit, TSTOP. Setting MS0B links channels 0 and 1 and configures them for buffered PWM operation. The TIMB channel 0 registers (TBCH0H-TBCH0L) initially control the buffered PWM output. TIMB status control register 0 (TBSC0) controls and monitors the PWM signal from the linked channels. MS0B takes priority over MS0A. Clearing the toggle-on-overflow bit, TOVx, inhibits output toggles on TIMB overflows. Subsequent output compares try to force the output to a state it is already in and have no effect. The result is a 0% duty cycle output. Setting the channel x maximum duty cycle bit (CHxMAX) and setting the TOVx bit generates a 100% duty cycle output. See 18.8.4 TIMB Channel Status and Control Registers. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface B (TIMB) Module Data Sheet 255 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module 18.4 Interrupts These TIMB sources can generate interrupt requests: * TIMB overflow flag (TOF) -- The TOF bit is set when the TIMB counter reaches the modulo value programmed in the TIMB counter modulo registers. The TIMB overflow interrupt enable bit, TOIE, enables TIMB overflow CPU interrupt requests. TOF and TOIE are in the TIMB status and control register. TIMB channel flags (CH1F-CH0F) -- The CHxF bit is set when an input capture or output compare occurs on channel x. Channel x TIMB CPU interrupt requests are controlled by the channel x interrupt enable bit, CHxIE. * Freescale Semiconductor, Inc... 18.5 Low-Power Modes The WAIT and STOP instructions put the microcontroller unit (MCU) in low powerconsumption standby modes. 18.5.1 Wait Mode The TIMB remains active after the execution of a WAIT instruction. In wait mode, the TIMB registers are not accessible by the central processor unit (CPU). Any enabled CPU interrupt request from the TIMB can bring the MCU out of wait mode. If TIMB functions are not required during wait mode, reduce power consumption by stopping the TIMB before executing the WAIT instruction. 18.5.2 Stop Mode The TIMB is inactive after the execution of a STOP instruction. The STOP instruction does not affect register conditions or the state of the TIMB counter. TIMB operation resumes when the MCU exits stop mode. 18.6 TIMB During Break Interrupts A break interrupt stops the TIMB counter and inhibits input captures. The system integration module (SIM) controls whether status bits in other modules can be cleared during the break state. The BCFE bit in the SIM break flag control register (SBFCR) enables software to clear status bits during the break state. To allow software to clear status bits during a break interrupt, write a 1 to the BCFE bit. If a status bit is cleared during the break state, it remains cleared when the MCU exits the break state. To protect status bits during the break state, write a 0 to the BCFE bit. With BCFE at 0 (its default state), software can read and write I/O registers during the break state without affecting status bits. Some status bits have a 2-step read/write Data Sheet 256 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface B (TIMB) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module I/O Signals clearing procedure. If software does the first step on such a bit before the break, the bit cannot change during the break state as long as BCFE is at 0. After the break, doing the second step clears the status bit. 18.7 I/O Signals Port B shares two of its pins with the TIMB. There is no external clock input to the TIMB prescaler. The two TIMB channel I/O pins are PTB6/TBCH0 and PTB7/TBCH1. See Section 12. Input/Output (I/O) Ports (PORTS). 18.7.1 TIMB Channel I/O Pins (PTB7/TBCH1-PTB6/TBCH0) Freescale Semiconductor, Inc... Each channel I/O pin is programmable independently as an input capture pin or an output compare pin. PTB6/TBCH0 and PTB7/TBCH1 can be configured as buffered output compare or buffered PWM pins. 18.8 I/O Registers These I/O registers control and monitor TIMB operation: * * * * * TIMB status and control register, TBSC TIMB control registers, TBCNTH-TBCNTL TIMB counter modulo registers, TBMODH-TBMODL TIMB channel status and control registers, TBSC0 and TBSC1 TIMB channel registers, TBCH0H-TBCH0L and TBCH1H-TBCH1L 18.8.1 TIMB Status and Control Register The TIMB status and control register: * * * * * Enables TIMB overflow interrupts Flags TIMB overflows Stops the TIMB counter Resets the TIMB counter Prescales the TIMB counter clock $002B Bit 7 Read: Write: Reset: TOF 0 0 R 6 TOIE 0 = Reserved 5 TSTOP 1 4 0 TRST 0 3 R 0 2 PS2 0 1 PS1 0 Bit 0 PS0 0 Address: Figure 18-5. TIMB Status and Control Register (TBSC) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface B (TIMB) Module Data Sheet 257 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module TOF -- TIMB Overflow Flag Bit This read/write flag is set when the TIMB counter reaches the modulo value programmed in the TIMB counter modulo registers. Clear TOF by reading the TIMB status and control register when TOF is set and then writing a 0 to TOF. If another TIMB overflow occurs before the clearing sequence is complete, then writing 0 to TOF has no effect. Therefore, a TOF interrupt request cannot be lost due to inadvertent clearing of TOF. Reset clears the TOF bit. Writing a 1 to TOF has no effect. 1 = TIMB counter has reached modulo value 0 = TIMB counter has not reached modulo value Freescale Semiconductor, Inc... TOIE -- TIMB Overflow Interrupt Enable Bit This read/write bit enables TIMB overflow interrupts when the TOF bit becomes set. Reset clears the TOIE bit. 1 = TIMB overflow interrupts enabled 0 = TIMB overflow interrupts disabled TSTOP -- TIMB Stop Bit This read/write bit stops the TIMB counter. Counting resumes when TSTOP is cleared. Reset sets the TSTOP bit, stopping the TIMB counter until software clears the TSTOP bit. 1 = TIMB counter stopped 0 = TIMB counter active NOTE: Do not set the TSTOP bit before entering wait mode if the TIMB is required to exit wait mode. Also, when the TSTOP bit is set and the timer is configured for input capture operation, input captures are inhibited until TSTOP is cleared. TRST -- TIMB Reset Bit Setting this write-only bit resets the TIMB counter and the TIMB prescaler. Setting TRST has no effect on any other registers. Counting resumes from $0000. TRST is cleared automatically after the TIMB counter is reset and always reads as 0. Reset clears the TRST bit. 1 = Prescaler and TIMB counter cleared 0 = No effect NOTE: Setting the TSTOP and TRST bits simultaneously stops the TIMB counter at a value of $0000. PS[2:0] -- Prescaler Select Bits These read/write bits select one of the seven prescaler outputs as the input to the TIMB counter as Table 18-1 shows. Reset clears the PS[2:0] bits. Data Sheet 258 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface B (TIMB) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module I/O Registers Table 18-1. Prescaler Selection PS[2:0] 000 001 010 011 100 101 110 111 TIMB Clock Source Internal bus clock / 1 Internal bus clock / 2 Internal bus clock / 4 Internal bus clock / 8 Internal bus clock / 16 Internal bus clock / 32 Internal bus clock / 64 Unused Freescale Semiconductor, Inc... 18.8.2 TIMB Counter Registers The two read-only TIMB counter registers contain the high and low bytes of the value in the TIMB counter. Reading the high byte (TBCNTH) latches the contents of the low byte (TBCNTL) into a buffer. Subsequent reads of TBCNTH do not affect the latched TBCNTL value until TBCNTL is read. Reset clears the TIMB counter registers. Setting the TIMB reset bit (TRST) also clears the TIMB counter registers. NOTE: If TBCNTH is read during a break interrupt, be sure to unlatch TBCNTL by reading TBCNTL before exiting the break interrupt. Otherwise, TBCNTL retains the value latched during the break. Register Name and Address Bit 7 Read: Write: Reset: BIT 15 R 0 6 BIT 14 R 0 TBCNTH -- $002C 5 BIT 13 R 0 4 BIT 12 R 0 3 BIT 11 R 0 2 BIT 10 R 0 1 BIT 9 R 0 Bit 0 BIT 8 R 0 Register Name and Address Bit 7 Read: Write: Reset: BIT 7 R 0 R 6 BIT 6 R 0 = Reserved TBCNTL -- $002D 5 BIT 5 R 0 4 BIT 4 R 0 3 BIT 3 R 0 2 BIT 2 R 0 1 BIT 1 R 0 Bit 0 BIT 0 R 0 Figure 18-6. TIMB Counter Registers (TBCNTH and TBCNTL) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface B (TIMB) Module Data Sheet 259 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module 18.8.3 TIMB Counter Modulo Registers The read/write TIMB modulo registers contain the modulo value for the TIMB counter. When the TIMB counter reaches the modulo value, the overflow flag (TOF) becomes set, and the TIMB counter resumes counting from $0000 at the next timer clock. Writing to the high byte (TMODH) inhibits the TOF bit and overflow interrupts until the low byte (TMODL) is written. Reset sets the TIMB counter modulo registers. Register Name and Address Bit 7 6 BIT 14 1 Read: Write: Reset: TBMODH -- $002E 5 BIT 13 1 4 BIT 12 1 3 BIT 11 1 2 BIT 10 1 1 BIT 9 1 Bit 0 BIT 8 1 Freescale Semiconductor, Inc... BIT 15 1 Register Name and Address Bit 7 Read: Write: Reset: BIT 7 1 6 BIT 6 1 TBMODL -- $002F 5 BIT 5 1 4 BIT 4 1 3 BIT 3 1 2 BIT 2 1 1 BIT 1 1 Bit 0 BIT 0 1 Figure 18-7. TIMB Counter Modulo Registers (TMODH and TMODL) NOTE: Reset the TIMB counter before writing to the TIMB counter modulo registers. 18.8.4 TIMB Channel Status and Control Registers Each of the TIMB channel status and control registers: * * * * * * * * Flags input captures and output compares Enables input capture and output compare interrupts Selects input capture, output compare, or PWM operation Selects high, low, or toggling output on output compare Selects rising edge, falling edge, or any edge as the active input capture trigger Selects output toggling on TIMB overflow Selects 0% and 100% PWM duty cycle Selects buffered or unbuffered output compare/PWM operation Data Sheet 260 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface B (TIMB) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module I/O Registers Register Name and Address Bit 7 Read: Write: Reset: CH0F 0 0 6 CH0IE 0 TBSC0 -- $0030 5 MS0B 0 TBSC1 -- $0033 6 CH1IE 0 5 0 R 0 4 MS1A 0 3 ELS1B 0 2 ELS1A 0 1 TOV1 0 Bit 0 CH1MAX 0 4 MS0A 0 3 ELS0B 0 2 ELS0A 0 1 TOV0 0 Bit 0 CH0MAX 0 Register Name and Address Bit 7 Read: Write: CH1F 0 0 R Freescale Semiconductor, Inc... Reset: = Reserved Figure 18-8. TIMB Channel Status and Control Registers (TBSC0-TBSC1) CHxF -- Channel x Flag Bit When channel x is an input capture channel, this read/write bit is set when an active edge occurs on the channel x pin. When channel x is an output compare channel, CHxF is set when the value in the TIMB counter registers matches the value in the TIMB channel x registers. When CHxIE = 1, clear CHxF by reading TIMB channel x status and control register with CHxF set, and then writing a 0 to CHxF. If another interrupt request occurs before the clearing sequence is complete, then writing 0 to CHxF has no effect. Therefore, an interrupt request cannot be lost due to inadvertent clearing of CHxF. Reset clears the CHxF bit. Writing a 1 to CHxF has no effect. 1 = Input capture or output compare on channel x 0 = No input capture or output compare on channel x CHxIE -- Channel x Interrupt Enable Bit This read/write bit enables TIMB CPU interrupts on channel x. Reset clears the CHxIE bit. 1 = Channel x CPU interrupt requests enabled 0 = Channel x CPU interrupt requests disabled MSxB -- Mode Select Bit B This read/write bit selects buffered output compare/PWM operation. MSxB exists only in the TIMB channel 0. Setting MS0B disables the channel 1 status and control register and reverts TBCH1 to general-purpose I/O. Reset clears the MSxB bit. 1 = Buffered output compare/PWM operation enabled 0 = Buffered output compare/PWM operation disabled MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface B (TIMB) Module Data Sheet 261 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module MSxA -- Mode Select Bit A When ELSxB:A 00, this read/write bit selects either input capture operation or unbuffered output compare/PWM operation. See Table 18-2. 1 = Unbuffered output compare/PWM operation 0 = Input capture operation When ELSxB:A = 00, this read/write bit selects the initial output level of the TCHx pin once PWM, input capture, or output compare operation is enabled. See Table 18-2. Reset clears the MSxA bit. 1 = Initial output level low 0 = Initial output level high Freescale Semiconductor, Inc... NOTE: Before changing a channel function by writing to the MSxB or MSxA bit, set the TSTOP and TRST bits in the TIMB status and control register (TBSC). ELSxB and ELSxA -- Edge/Level Select Bits When channel x is an input capture channel, these read/write bits control the active edge-sensing logic on channel x. When channel x is an output compare channel, ELSxB and ELSxA control the channel x output behavior when an output compare occurs. When ELSxB and ELSxA are both clear, channel x is not connected to port B, and pin PTBx/TBCHx is available as a general-purpose I/O pin. However, channel x is at a state determined by these bits and becomes transparent to the respective pin when PWM, input capture, or output compare mode is enabled. Table 18-2 shows how ELSxB and ELSxA work. Reset clears the ELSxB and ELSxA bits. Table 18-2. Mode, Edge, and Level Selection MSxB:MSxA X0 ELSxB:ELSxA 00 Output Preset X1 00 00 00 01 01 01 1X 1X 1X 00 01 10 11 01 10 11 01 10 11 Mode Configuration Pin under Port Control; Initialize Timer Output Level High Pin under Port Control; Initialize Timer Output Level Low Capture on Rising Edge Only Capture on Falling Edge Only Capture on Rising or Falling Edge Toggle Output on Compare Clear Output on Compare Set Output on Compare Toggle Output on Compare Clear Output on Compare Set Output on Compare Input Capture Output Compare or PWM Buffered Output Compare or Buffered PWM NOTE: Before enabling a TIMB channel register for input capture operation, make sure that the PTBx/TBCHx pin is stable for at least two bus clocks. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface B (TIMB) Module MOTOROLA Data Sheet 262 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module I/O Registers TOVx -- Toggle-On-Overflow Bit When channel x is an output compare channel, this read/write bit controls the behavior of the channel x output when the TIMB counter overflows. When channel x is an input capture channel, TOVx has no effect. Reset clears the TOVx bit. 1 = Channel x pin toggles on TIMB counter overflow. 0 = Channel x pin does not toggle on TIMB counter overflow. NOTE: When TOVx is set, a TIMB counter overflow takes precedence over a channel x output compare if both occur at the same time. CHxMAX -- Channel x Maximum Duty Cycle Bit When the TOVx bit is at 1 and clear output on compare is selected, setting the CHxMAX bit forces the duty cycle of buffered and unbuffered PWM signals to 100 percent. As Figure 18-9 shows, the CHxMAX bit takes effect in the cycle after it is set or cleared. The output stays at 100 percent duty cycle level until the cycle after CHxMAX is cleared. NOTE: The PWM 100 percent duty cycle is defined as output high all of the time. To generate the 100 percent duty cycle, use the CHxMAX bit in the TSCx register. The PWM 0 percent duty cycle is defined as output low all of the time. To generate the 0 percent duty cycle, select clear output on compare and then clear the TOVx bit (CHxMAX = 0). OVERFLOW OVERFLOW OVERFLOW OVERFLOW OVERFLOW Freescale Semiconductor, Inc... PERIOD PTEx/TCHx TOV = 1 OUTPUT COMPARE CHxMAX OUTPUT COMPARE OUTPUT COMPARE OUTPUT COMPARE TOV = 0 Figure 18-9. CHxMAX Latency MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Timer Interface B (TIMB) Module Data Sheet 263 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Timer Interface B (TIMB) Module 18.8.5 TIMB Channel Registers These read/write registers contain the captured TIMB counter value of the input capture function or the output compare value of the output compare function. The state of the TIMB channel registers after reset is unknown. In input capture mode (MSxB-MSxA = 0:0), reading the high byte of the TIMB channel x registers (TBCHxH) inhibits input captures until the low byte (TBCHxL) is read. In output compare mode (MSxB-MSxA 0:0), writing to the high byte of the TIMB channel x registers (TBCHxH) inhibits output compares and the CHxF bit until the low byte (TBCHxL) is written. Register Name and Address Bit 7 Read: Write: Reset: Register Name and Address Bit 7 Read: Write: Reset: Register Name and Address Bit 7 Read: Write: Reset: Register Name and Address Bit 7 Read: Write: Reset: BIT 7 6 BIT 6 5 BIT 5 BIT 15 6 BIT 14 5 BIT 13 BIT 7 6 BIT 6 5 BIT 5 BIT 15 6 BIT 14 TBCH0H -- $0031 5 BIT 13 4 BIT 12 3 BIT 11 2 BIT 10 1 BIT 9 Bit 0 BIT 8 Freescale Semiconductor, Inc... Indeterminate after reset TBCH0L -- $0032 4 BIT 4 3 BIT 3 2 BIT 2 1 BIT 1 Bit 0 BIT 0 Indeterminate after reset TBCH1H -- $0034 4 BIT 12 3 BIT 11 2 BIT 10 1 BIT 9 Bit 0 BIT 8 Indeterminate after reset TBCH1L -- $0035 4 BIT 4 3 BIT 3 2 BIT 2 1 BIT 1 Bit 0 BIT 0 Indeterminate after reset Figure 18-10. TIMB Channel Registers (TBCH0H/L-TBCH1H/L) Data Sheet 264 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Timer Interface B (TIMB) Module MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 19. Development Support 19.1 Introduction This section describes the break module, the monitor module (MON), and the monitor mode entry methods. Freescale Semiconductor, Inc... 19.2 Break Module (BRK) The break module can generate a break interrupt that stops normal program flow at a defined address to enter a background program. Features of the break module include: * * * * Accessible input/output (I/O) registers during the break Interrupt Central processor unit (CPU) generated break interrupts Software-generated break interrupts Computer operating properly (COP) disabling during break interrupts 19.2.1 Functional Description When the internal address bus matches the value written in the break address registers, the break module issues a breakpoint signal (BKPT) to the system integration module (SIM). The SIM then causes the CPU to load the instruction register with a software interrupt instruction (SWI). The program counter vectors to $FFFC and $FFFD ($FEFC and $FEFD in monitor mode). The following events can cause a break interrupt to occur: * * A CPU generated address (the address in the program counter) matches the contents of the break address registers. Software writes a 1 to the BRKA bit in the break status and control register. When a CPU generated address matches the contents of the break address registers, the break interrupt is generated. A return-from-interrupt instruction (RTI) in the break routine ends the break interrupt and returns the microcontroller unit (MCU) to normal operation. Figure 19-2 shows the structure of the break module. Figure 19-3 provides a summary of the I/O registers. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Development Support Data Sheet 265 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support INTERNAL BUS M68HC08 CPU CPU REGISTERS ARITHMETIC/LOGIC UNIT (ALU) SINGLE BREAKPOINT BREAK MODULE PORT A DDRA 5-BIT KEYBOARD INTERRUPT MODULE PTA6/SS PTA5/SPSCK PTA4/KBD4 PTA3/KBD3 PTA2/KBD2 PTA1/KBD1 2-CHANNEL TIMER INTERFACE MODULE A PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PORT B DDRB PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK PTC1/MOSI PTC0/MISO PTD1/TACH1 PTD0/TACH0 PTE1/RxD PTE0/TxD PORT C PORT E PORT D CONTROL AND STATUS REGISTERS 64 BYTES USER FLASH 15,872 BYTES USER RAM 512 BYTES Freescale Semiconductor, Inc... MONITOR ROM 310 BYTES FLASH PROGRAMMING (BURN-IN) ROM 1024 BYTES USER FLASH VECTOR SPACE 36 BYTES 2-CHANNEL TIMER INTERFACE MODULE B ENHANCED SERIAL COMMUNICATION INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE OSC2 OSC1 INTERNAL CLOCK GENERATOR MODULE SERIAL PERIPHERAL INTERFACE MODULE RST 24 INTERNAL SYSTEM INTEGRATION MODULE SINGLE EXTERNAL IRQ MODULE CONFIGURATION REGISTER MODULE PERIODIC WAKEUP TIMEBASE MODULE ARBITER MODULE PRESCALER MODULE IRQ VREFH VDDA VREFL VSSA VDD VSS DDRE DDRD DDRC 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE SECURITY MODULE POWER BEMF MODULE Figure 19-1. Block Diagram Highlighting BRK and MON Blocks Data Sheet 266 Development Support MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support Break Module (BRK) ADDRESS BUS[15:8] BREAK ADDRESS REGISTER HIGH 8-BIT COMPARATOR ADDRESS BUS[15:0] CONTROL 8-BIT COMPARATOR BREAK ADDRESS REGISTER LOW BKPT (TO SIM) Freescale Semiconductor, Inc... ADDRESS BUS[7:0] Figure 19-2. Break Module Block Diagram L Addr. $FE00 Register Name Break Status Register Read: (SBSR) Write: See page 270. Reset: Break Flag Control Read: Register (SBFCR) Write: See page 271. Reset: Break Address High Read: Register (BRKH) Write: See page 270. Reset: Break Address Low Read: Register (BRKL) Write: See page 270. Reset: Break Status and Control Read: Register (BSCR) Write: See page 269. Reset: Bit 7 R 6 R 5 R 4 R 3 R 2 R 1 SBSW Note(1) 0 BCFE 0 Bit 15 0 Bit 7 0 BRKE 0 Bit 14 0 Bit 6 0 BRKA 0 = Unimplemented Bit 13 0 Bit 5 0 0 0 Bit 12 0 Bit 4 0 0 0 R Bit 11 0 Bit 3 0 0 0 = Reserved Bit 10 0 Bit 2 0 0 0 Bit 9 0 Bit 1 0 0 0 Bit 8 0 Bit 0 0 0 0 R R R R R R R Bit 0 R $FE03 $FE09 $FE0A $FE0B 1. Writing a 0 clears SBSW. Figure 19-3. Break I/O Register Summary MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Development Support Data Sheet 267 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support When the internal address bus matches the value written in the break address registers or when software writes a 1 to the BRKA bit in the break status and control register, the CPU starts a break interrupt by: * * Loading the instruction register with the SWI instruction Loading the program counter with $FFFC and $FFFD ($FEFC and $FEFD in monitor mode) The break interrupt timing is: * When a break address is placed at the address of the instruction opcode, the instruction is not executed until after completion of the break interrupt routine. When a break address is placed at an address of an instruction operand, the instruction is executed before the break interrupt. When software writes a 1 to the BRKA bit, the break interrupt occurs just before the next instruction is executed. Freescale Semiconductor, Inc... * * By updating a break address and clearing the BRKA bit in a break interrupt routine, a break interrupt can be generated continuously. CAUTION: A break address should be placed at the address of the instruction opcode. When software does not change the break address and clears the BRKA bit in the first break interrupt routine, the next break interrupt will not be generated after exiting the interrupt routine even when the internal address bus matches the value written in the break address registers. 19.2.1.1 Flag Protection During Break Interrupts The system integration module (SIM) controls whether or not module status bits can be cleared during the break state. The BCFE bit in the break flag control register (SBFCR) enables software to clear status bits during the break state. See 14.7.3 SIM Break Flag Control Register and the Break Interrupts subsection for each module. 19.2.1.2 TIM During Break Interrupts A break interrupt stops the timer counter. 19.2.1.3 COP During Break Interrupts The COP is disabled during a break interrupt when VTST is present on the RST pin. Data Sheet 268 Development Support MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support Break Module (BRK) 19.2.2 Break Module Registers These registers control and monitor operation of the break module: * * * * * Break status and control register (BSCR) Break address register high (BRKH) Break address register low (BRKL) Break status register (SBSR) Break flag control register (SBFCR) 19.2.2.1 Break Status and Control Register Freescale Semiconductor, Inc... The break status and control register (BSCR) contains break module enable and status bits. Address: $FE0B Bit 7 Read: Write: Reset: BRKE 0 6 BRKA 0 5 0 0 4 0 0 3 0 0 2 0 0 1 0 0 Bit 0 0 0 = Unimplemented Figure 19-4. Break Status and Control Register (BSCR) BRKE -- Break Enable Bit This read/write bit enables breaks on break address register matches. Clear BRKE by writing a 0 to bit 7. Reset clears the BRKE bit. 1 = Breaks enabled on 16-bit address match 0 = Breaks disabled BRKA -- Break Active Bit This read/write status and control bit is set when a break address match occurs. Writing a 1 to BRKA generates a break interrupt. Clear BRKA by writing a 0 to it before exiting the break routine. Reset clears the BRKA bit. 1 = Break address match 0 = No break address match MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Development Support Data Sheet 269 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support 19.2.2.2 Break Address Registers The break address registers (BRKH and BRKL) contain the high and low bytes of the desired breakpoint address. Reset clears the break address registers. Address: $FE09 Bit 7 Read: Write: Reset: Bit 15 0 6 Bit 14 0 5 Bit 13 0 4 Bit 12 0 3 Bit 11 0 2 Bit 10 0 1 Bit 9 0 Bit 0 Bit 8 0 Figure 19-5. Break Address Register High (BRKH) Freescale Semiconductor, Inc... Address: $FE0A Bit 7 Read: Write: Reset: Bit 7 0 6 Bit 6 0 5 Bit 5 0 4 Bit 4 0 3 Bit 3 0 2 Bit 2 0 1 Bit 1 0 Bit 0 Bit 0 0 Figure 19-6. Break Address Register Low (BRKL) 19.2.2.3 Break Status Register The break status register (SBSR) contains a flag to indicate that a break caused an exit from wait mode. This register is only used in emulation mode. Address: $FE00 Bit 7 Read: Write: Reset: R = Reserved 1. Writing a 0 clears SBSW. R 6 R 5 R 4 R 3 R 2 R 1 SBSW Note(1) 0 Bit 0 R Figure 19-7. Break Status Register (SBSR) SBSW -- SIM Break Stop/Wait SBSW can be read within the break state SWI routine. The user can modify the return address on the stack by subtracting one from it. 1 = Wait mode was exited by break interrupt 0 = Wait mode was not exited by break interrupt Data Sheet 270 Development Support MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support Monitor Module (MON) 19.2.2.4 Break Flag Control Register The break control register (SBFCR) contains a bit that enables software to clear status bits while the MCU is in a break state. Address: $FE03 Bit 7 Read: Write: Reset: BCFE 0 R = Reserved 6 R 5 R 4 R 3 R 2 R 1 R Bit 0 R Freescale Semiconductor, Inc... Figure 19-8. Break Flag Control Register (SBFCR) BCFE -- Break Clear Flag Enable Bit This read/write bit enables software to clear status bits by accessing status registers while the MCU is in a break state. To clear status bits during the break state, the BCFE bit must be set. 1 = Status bits clearable during break 0 = Status bits not clearable during break 19.2.3 Low-Power Modes The WAIT and STOP instructions put the MCU in low power- consumption standby modes. If enabled, the break module will remain enabled in wait and stop modes. However, since the internal address bus does not increment in these modes, a break interrupt will never be triggered. 19.3 Monitor Module (MON) The monitor module allows debugging and programming of the microcontroller unit (MCU) through a single-wire interface with a host computer. Monitor mode entry can be achieved without use of the higher test voltage, VTST, as long as vector addresses $FFFE and $FFFF are blank, thus reducing the hardware requirements for in-circuit programming. Features of the monitor module include: * * * * * Normal user-mode pin functionality One pin dedicated to serial communication between MCU and host computer Standard non-return-to-zero (NRZ) communication with host computer Standard communication baud rate (9600 @ 2.4576-MHz bus frequency) Execution of code in random-access memory (RAM) or FLASH MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Development Support Data Sheet 271 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support * * * * FLASH memory security feature(1) FLASH memory programming interface Monitor mode entry without high voltage, VTST, if reset vector is blank ($FFFE and $FFFF contain $FF) Normal monitor mode entry if VTST is applied to IRQ 19.3.1 Functional Description Figure 19-9 shows a simplified diagram of the monitor mode. Freescale Semiconductor, Inc... The monitor module receives and executes commands from a host computer. Figure 19-10 and Figure 19-11 show example circuits used to enter monitor mode and communicate with a host computer via a standard RS-232 interface. Simple monitor commands can access any memory address. In monitor mode, the MCU can execute code downloaded into RAM by a host computer while most MCU pins retain normal operating mode functions. All communication between the host computer and the MCU is through the PTA0 pin. A level-shifting and multiplexing interface is required between PTA0 and the host computer. PTA0 is used in a wired-OR configuration and requires a pullup resistor. Table 19-1 shows the pin conditions for entering monitor mode. As specified in the table, monitor mode may be entered after a power-on reset (POR) and will allow communication at 9600 baud provided one of the following sets of conditions is met: * If $FFFE and $FFFF does not contain $FF (programmed state): - The external clock is 4.9152 MHz (9600 baud) - PTB5 = low - IRQ = VTST If $FFFE and $FFFF do not contain $FF (programmed state): - The external clock is 9.8304 MHz (9600 baud) - PTB5 = high - IRQ = VTST If $FFFE and $FFFF contain $FF (erased state): - The external clock is 9.8304 MHz (9600 baud) - IRQ = VDD (this can be implemented through the internal IRQ pullup) If $FFFE and $FFFF contain $FF (erased state): - The ICG clock is nominal 1.6 MHz (nominal 6300 baud) - IRQ = VSS * * * 1. No security feature is absolutely secure. However, Motorola's strategy is to make reading or copying the FLASH difficult for unauthorized users. Data Sheet 272 Development Support MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support Monitor Module (MON) POR RESET NO IRQ = VTST? YES CONDITIONS FROM Table 19-1 PTA0 = 1, PTA1 = 0, RESET VECTOR BLANK? YES NO PTA0 = 1, PTA1 = 0, PTB4 = 1, AND PTB3 = 0? YES NORMAL USER MODE NORMAL MONITOR MODE NO Freescale Semiconductor, Inc... FORCED MONITOR MODE INVALID USER MODE HOST SENDS 8 SECURITY BYTES IS RESET POR? NO YES YES ARE ALL SECURITY BYTES CORRECT? NO ENABLE FLASH DISABLE FLASH MONITOR MODE ENTRY DEBUGGING AND FLASH PROGRAMMING (IF FLASH IS ENABLED) EXECUTE MONITOR CODE YES DOES RESET OCCUR? NO Figure 19-9. Simplified Monitor Mode Entry Flowchart MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Development Support Data Sheet 273 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support MC68HC908EY16 N.C. RST VDD VDDA MAX232 1 1 F + 3 4 C1+ VCC 16 + C1- C2+ GND 15 V+ 2 V- 6 + DB9 2 3 5 7 8 10 9 74HC125 3 2 1 1 F 74HC125 5 6 4 10 k PTA0 VSSA VSS PTA1 VDD 9.1 V PTB3 1 F 1 F + 1 k IRQ PTB4 VDD 9.8304-MHz CLOCK OSC1 VDD 0.1 F VDD 10 k 10 k PTB5 10 k 10 k Freescale Semiconductor, Inc... 1 F + 5 C2- Figure 19-10. Normal Monitor Mode Circuit MC68HC908EY16 N.C. RST VDD VDDA MAX232 1 1 F + 3 4 1 F + 5 C2- DB9 2 3 5 7 8 10 9 74HC125 3 2 1 C1+ VCC 16 + C1- C2+ GND 15 V+ 2 V- 6 + 1 F 74HC125 5 6 4 10 k PTA0 VSSA VSS PTA1 VDD 1 F 1 F + N.C. IRQ PTB4 PTB5 PTB3 10 k N.C. N.C. N.C. 9.8304-MHz CLOCK VDD OSC1 0.1 F VDD Figure 19-11. Forced Monitor Mode (IRQ = VDD) Data Sheet 274 Development Support MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support Monitor Module (MON) Table 19-1. Monitor Mode Signal Requirements and Options Serial Reset Communication RST Vector PTA0 PTA1 VDD or VTST VDD or VTST VDD $FF (blank) VSS VDD or VSS VDD VDD or VTST Not $FF 1 0 X X X ON Disabled Mode Selection PTB4 PTB3 Divider ICG PTB5 COP External Bus Clock Frequency 4.9152 MHz 2.4576 MHz Baud Rate Communication Speed Mode IRQ VTST Normal Monitor VTST X 1 0 1 0 0 OFF Disabled 9600 X 1 0 1 0 1 OFF Disabled Freescale Semiconductor, Inc... 9.8304 MHz 9.8304 MHz -- 2.4576 MHz 2.4576 MHz Nominal 1.6 MHz Nominal 1.6 MHz 9600 VDD Forced Monitor 1 0 X X X OFF Disabled 9600 Nominal 6300 User X X X X X CN Enabled -- X MON08 VTST RST Function [4] [6] [Pin No.] -- COM [8] SSEL [10] MOD0 MOD1 [12] [14] DIV4 [16] -- -- OSC1 [13] -- -- 1. PTA0 must have a pullup resistor to VDD in monitor mode. 2. Communication speed in the table is an example to obtain a baud rate of 9600 except the forced monitor IRQ = VSS case. Baud rate using external oscillator is bus frequency / 256. 3. External clock is a 4.9152 MHz or 9.8304 MHz canned oscillator on OSC1. 4. X = don't care 5. MON08 pin refers to P&E Microcomputer Systems' MON08-Cyclone 2 by 8-pin connector. NC NC NC NC NC NC OSC1 VDD 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 GND RST IRQ PTA0 PTA1 PTB3 PTB4 PTB5 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Development Support Data Sheet 275 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support Enter monitor mode with pin configuration shown in Table 19-1 by pulling RST low and then high. The rising edge of RST latches monitor mode. Once monitor mode is latched, the levels on the port pins except PTA0 can change. Once out of reset, the MCU waits for the host to send eight security bytes (see 19.3.2 Security). After the security bytes, the MCU sends a break signal (10 consecutive 0s) to the host, indicating that it is ready to receive a command. 19.3.1.1 Normal Monitor Mode If VTST is applied to IRQ and PTB5 is low upon monitor mode entry, the bus frequency is a divide-by-two of the input clock. If PTB5 is high with VTST applied to IRQ upon monitor mode entry, the bus frequency will be a divide-by-four of the input clock. Holding the PTB5 pin low when entering monitor mode causes a bypass of a divide-by-two stage at the oscillator only if VTST is applied to IRQ. In this event, the CGMOUT frequency is equal to the CGMXCLK frequency, and the OSC1 input directly generates internal bus clocks. In this case, the OSC1 signal must have a 50% duty cycle at maximum bus frequency. When monitor mode was entered with VTST on IRQ, the computer operating properly (COP) is disabled as long as VTST is applied to either IRQ or RST. This condition states that as long as VTST is maintained on the IRQ pin after entering monitor mode, or if VTST is applied to RST after the initial reset to get into monitor mode (when VTST was applied to IRQ), then the COP will be disabled. In the latter situation, after VTST is applied to the RST pin, VTST can be removed from the IRQ pin in the interest of freeing the IRQ for normal functionality in monitor mode. 19.3.1.2 Forced Monitor Mode If entering monitor mode without high voltage on IRQ, then all port B pin requirements and conditions, including the PTB5 frequency divisor selection, are not in effect. This is to reduce circuit requirements when performing in-circuit programming. NOTE: If the reset vector is blank and monitor mode is entered, the chip will see an additional reset cycle after the initial power-on reset (POR). Once the reset vector has been programmed, the traditional method of applying a voltage, VTST, to IRQ must be used to enter monitor mode. With VDD on IRQ, an external oscillator of 9.8034 MHz is required for a baud rate of 9600, as the internal bus frequency is automatically set to the external frequency divided by four. With VSS on IRQ at the monitor entry, the ICG is on. In this case, the bus frequency is a nominal 1.6 MHz and the baud rate is a nominal 6300. When the forced monitor mode is entered the COP is always disabled regardless of the state of IRQ or RST. Data Sheet 276 Development Support MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Freescale Semiconductor, Inc... For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support Monitor Module (MON) 19.3.1.3 Monitor Vectors In monitor mode, the MCU uses different vectors for reset, SWI (software interrupt), and break interrupt than those for user mode. The alternate vectors are in the $FE page instead of the $FF page and allow code execution from the internal monitor firmware instead of user code. Table 19-2 summarizes the differences between user mode and monitor mode. Table 19-2. Mode Differences Functions Modes Freescale Semiconductor, Inc... Reset Vector High $FFFE $FEFE Reset Vector Low $FFFF $FEFF Break Vector High $FFFC $FEFC Break Vector Low $FFFD $FEFD SWI Vector High $FFFC $FEFC SWI Vector Low $FFFD $FEFD User Monitor 19.3.1.4 Data Format Communication with the monitor ROM is in standard non-return-to-zero (NRZ) mark/space data format. Transmit and receive baud rates must be identical. NEXT START BIT START BIT BIT 0 BIT 1 BIT 2 BIT 3 BIT 4 BIT 5 BIT 6 BIT 7 STOP BIT Figure 19-12. Monitor Data Format 19.3.1.5 Break Signal A start bit (0) followed by nine 0 bits is a break signal. When the monitor receives a break signal, it drives the PTA0 pin high for the duration of approximately two bits and then echoes back the break signal. MISSING STOP BIT APPROXIMATELY 2 BITS DELAY BEFORE ZERO ECHO 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 Figure 19-13. Break Transaction MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Development Support Data Sheet 277 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support 19.3.1.6 Baud Rate The communication baud rate is controlled by the crystal frequency or external clock and the state of the PTB5 pin (when IRQ is set to VTST) upon entry into monitor mode. If monitor mode was entered with VDD on IRQ and the reset vector blank, then the baud rate is independent of PTB5. Table 19-1 also lists external frequencies required to achieve a standard baud rate of 7200 bps. The effective baud rate is the bus frequency divided by 278. If using a crystal as the clock source, be aware of the upper frequency limit that the internal clock module can handle. See 20.6 Control Timing for this limit. Freescale Semiconductor, Inc... 19.3.1.7 Commands The monitor ROM firmware uses these commands: * * * * * * READ (read memory) WRITE (write memory) IREAD (indexed read) IWRITE (indexed write) READSP (read stack pointer) RUN (run user program) The monitor ROM firmware echoes each received byte back to the PTA0 pin for error checking. An 11-bit delay at the end of each command allows the host to send a break character to cancel the command. A delay of two bit times occurs before each echo and before READ, IREAD, or READSP data is returned. The data returned by a read command appears after the echo of the last byte of the command. NOTE: Wait one bit time after each echo before sending the next byte. FROM HOST READ READ ADDRESS HIGH ADDRESS HIGH ADDRESS LOW ADDRESS LOW DATA 4 ECHO 1 4 1 4 1 3, 2 4 RETURN Notes: 1 = Echo delay, approximately 2 bit times 2 = Data return delay, approximately 2 bit times 3 = Cancel command delay, 11 bit times 4 = Wait 1 bit time before sending next byte. Figure 19-14. Read Transaction Data Sheet 278 Development Support MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support Monitor Module (MON) FROM HOST WRITE 3 ECHO 1 WRITE 3 ADDRESS HIGH ADDRESS HIGH ADDRESS LOW ADDRESS LOW DATA DATA 1 3 1 3 1 2, 3 Notes: 1 = Echo delay, approximately 2 bit times 2 = Cancel command delay, 11 bit times 3 = Wait 1 bit time before sending next byte. Figure 19-15. Write Transaction Freescale Semiconductor, Inc... A brief description of each monitor mode command is given in Table 19-3 through Table 19-8. Table 19-3. READ (Read Memory) Command Description Operand Data Returned Opcode Read byte from memory 2-byte address in high-byte:low-byte order Returns contents of specified address $4A Command Sequence SENT TO MONITOR READ READ ADDRESS HIGH ADDRESS HIGH ADDRESS LOW ADDRESS LOW DATA ECHO RETURN Table 19-4. WRITE (Write Memory) Command Description Operand Data Returned Opcode FROM HOST Write byte to memory 2-byte address in high-byte:low-byte order; low byte followed by data byte None $49 Command Sequence WRITE WRITE ADDRESS HIGH ADDRESS HIGH ADDRESS LOW ADDRESS LOW DATA DATA ECHO MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Development Support Data Sheet 279 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support Table 19-5. IREAD (Indexed Read) Command Description Operand Data Returned Opcode Read next 2 bytes in memory from last address accessed None Returns contents of next two addresses $1A Command Sequence FROM HOST IREAD IREAD DATA DATA Freescale Semiconductor, Inc... ECHO RETURN Table 19-6. IWRITE (Indexed Write) Command Description Operand Data Returned Opcode Write to last address accessed + 1 Single data byte None $19 Command Sequence FROM HOST IWRITE IWRITE DATA DATA ECHO A sequence of IREAD or IWRITE commands can access a block of memory sequentially over the full 64-Kbyte memory map. Table 19-7. READSP (Read Stack Pointer) Command Description Operand Data Returned Opcode Reads stack pointer None Returns incremented stack pointer value (SP + 1) in high-byte:low-byte order $0C Command Sequence FROM HOST READSP READSP SP HIGH SP LOW ECHO RETURN Data Sheet 280 Development Support MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support Monitor Module (MON) Table 19-8. RUN (Run User Program) Command Description Operand Data Returned Opcode Executes PULH and RTI instructions None None $28 Command Sequence FROM HOST RUN RUN Freescale Semiconductor, Inc... ECHO The MCU executes the SWI and PSHH instructions when it enters monitor mode. The RUN command tells the MCU to execute the PULH and RTI instructions. Before sending the RUN command, the host can modify the stacked CPU registers to prepare to run the host program. The READSP command returns the incremented stack pointer value, SP + 1. The high and low bytes of the program counter are at addresses SP + 5 and SP + 6. SP HIGH BYTE OF INDEX REGISTER CONDITION CODE REGISTER ACCUMULATOR LOW BYTE OF INDEX REGISTER HIGH BYTE OF PROGRAM COUNTER LOW BYTE OF PROGRAM COUNTER SP + 1 SP + 2 SP + 3 SP + 4 SP + 5 SP + 6 SP + 7 Figure 19-16. Stack Pointer at Monitor Mode Entry 19.3.2 Security A security feature discourages unauthorized reading of FLASH locations while in monitor mode. The host can bypass the security feature at monitor mode entry by sending eight security bytes that match the bytes at locations $FFF6-$FFFD. Locations $FFF6-$FFFD contain user-defined data. NOTE: Do not leave locations $FFF6-$FFFD blank. For security reasons, program locations $FFF6-$FFFD even if they are not used for vectors. During monitor mode entry, the MCU waits after the power-on reset for the host to send the eight security bytes on pin PTA0. If the received bytes match those at locations $FFF6-$FFFD, the host bypasses the security feature and can read all FLASH locations and execute code from FLASH. Security remains bypassed until MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Development Support Data Sheet 281 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Development Support a power-on reset occurs. If the reset was not a power-on reset, security remains bypassed and security code entry is not required. See Figure 19-17. Upon power-on reset, if the received bytes of the security code do not match the data at locations $FFF6-$FFFD, the host fails to bypass the security feature. The MCU remains in monitor mode, but reading a FLASH location returns an invalid value and trying to execute code from FLASH causes an illegal address reset. After receiving the eight security bytes from the host, the MCU transmits a break character, signifying that it is ready to receive a command. NOTE: The MCU does not transmit a break character until after the host sends the eight security bytes. Freescale Semiconductor, Inc... VDD 4096 + 32 CGMXCLK CYCLES RST COMMAND 1 BYTE 2 ECHO BYTE 8 ECHO 2 BREAK 4 1 COMMAND ECHO BYTE 1 BYTE 2 FROM HOST PA0 5 FROM MCU 1 BYTE 1 ECHO 4 1 Notes: 1 = Echo delay, approximately 2 bit times 2 = Data return delay, approximately 2 bit times 4 = Wait 1 bit time before sending next byte 5 = Wait until the monitor ROM runs Figure 19-17. Monitor Mode Entry Timing To determine whether the security code entered is correct, check to see if bit 6 of RAM address $40 is set. If it is, then the correct security code has been entered and FLASH can be accessed. If the security sequence fails, the device should be reset by a power-on reset and brought up in monitor mode to attempt another entry. After failing the security sequence, the FLASH module can also be mass erased by executing an erase routine that was downloaded into internal RAM. The mass erase operation clears the security code locations so that all eight security bytes become $FF (blank). Data Sheet 282 Development Support MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com BYTE 8 Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 20. Electrical Specifications 20.1 Introduction This section contains preliminary electrical and timing specifications. 20.2 Absolute Maximum Ratings Freescale Semiconductor, Inc... Maximum ratings are the extreme limits to which the microcontroller unit (MCU) can be exposed without permanently damaging it. NOTE: This device is not guaranteed to operate properly at the maximum ratings. Refer to 20.5 DC Electrical Characteristics for guaranteed operating conditions. Characteristic(1) Supply voltage Input voltage Maximum current per pin excluding VDD, VSS, and PTA0-PTA6 and PTC0-PTC1 Maximum current for pins PTA0-PTA6 and PTC0-PTC1 Maximum current out of VSS Maximum current into VDD Storage temperature 1. Voltages referenced to VSS Symbol VDD VIn I IPTA0-IPTA6, IPTC0-IPTC1 IMVSS IMVDD TSTG Value -0.3 to +6.0 VSS -0.3 to VDD +0.3 15 Unit V V mA 25 100 100 -55 to +150 mA mA mA C NOTE: This device contains circuitry to protect the inputs against damage due to high static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum-rated voltages to this high-impedance circuit. For proper operation, it is recommended that VIn and VOut be constrained to the range VSS (VIn or VOut) VDD. Reliability of operation is enhanced if unused inputs are connected to an appropriate logic voltage level (for example, either VSS or VDD). MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Electrical Specifications Data Sheet 283 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Electrical Specifications 20.3 Functional Operating Range Characteristic Operating temperature range Operating voltage range Symbol TA VDD Value -40 to 135 5.0 10% Unit C V 20.4 Thermal Characteristics Characteristic Symbol JA PI/O PD Value 100 User determined PD = (IDD x VDD) + PI/O = K/(TJ + 273C) PD x (TA + 273C) + PD2 x JA TA + (PD x JA) Unit C/W W W Freescale Semiconductor, Inc... Thermal resistance QFP (32 pins) I/O pin power dissipation Power dissipation(1) Constant(2) Average junction temperature K TJ W/C C 1. Power dissipation is a function of temperature. 2. K is a constant unique to the device. K can be determined for a known TA and measured PD. With this value of K, PD and TJ can be determined for any value of TA. 20.5 DC Electrical Characteristics Characteristic(1) Output high voltage ILoad = -2.0 mA, all I/O pins ILoad = -5.0 mA, all I/O pins ILoad = -10.0 mA, all I/O pins ILoad = -15.0 mA, PTA0-PTA6/SS and PTC0-PTC1 only Output low voltage ILoad = 1.6 mA, all I/O pins ILoad = 5.0 mA, all I/O pins ILoad = 10.0 mA, all I/O pins ILoad = 15.0 mA, PTA0-PTA6/SS and PTC0-PTC1 only Input high voltage -- all ports, IRQ, RST Input low voltage -- all ports, IRQ, RST DC injection current, all ports(3) Total DC current injection (sum of all I/O) Symbol Min VDD -0.7 VDD -1.1 VDD -1.7 VDD -1.5 Typ(2) VDD -0.54 VDD -0.91 VDD -1.51 VDD -0.81 Max Unit VOH -- -- -- -- V VOL -- -- -- -- 0.7 x VDD VSS - 2.0 - 25 0.31 0.56 0.99 1.44 -- -- -- 0.4 1 1.5 1.8 VDD + 0.3 0.3 x VDD + 2.0 + 25 V VIH VIL IINJ IINJTOT V V mA mA -- Continued on next page Data Sheet 284 Electrical Specifications MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Electrical Specifications DC Electrical Characteristics Characteristic(1) VDD + VDDA supply current Run(4),(5) Wait(5), (6) Stop (LVI off) @ 25C(7) Stop (LVI on) @ 25C Stop (LVI off), -40C to 135C Stop (LVI on), -40C to 135C I/O ports Hi-Z leakage current(8) Input current - RST, OSC1 Symbol Min Typ(2) Max Unit IDD -- -- -- -- -- -- -10 -1 -- -- 0 0 0.035 VDD+ 3.5 3.90 4.00 -- 24 18 5.2 0.83 0.19 3.0 0.19 -- -- -- -- -- 700 -- 25 7.0 2.00 0.24 30 0.30 +10 +1 12 8 100 800 -- VDD+ 4.5 mA mA A mA A mA A A pF mV mV V/ms V V V V k IIL IIn COut CIn VPOR VPOR RPOR VTST VTRIPF VTRIPR VHYS RPU Freescale Semiconductor, Inc... Capacitance Ports (as input or output) POR rearm voltage(9) POR reset voltage(10) POR rise time ramp rate Monitor mode entry voltage Low-voltage inhibit reset, trip falling voltage(11) Low-voltage inhibit reset, trip rising voltage(12) Low-voltage inhibit reset/recover hysteresis(13) Pullup resistor -- PTA0-PTA6/SS(14), IRQ, RST 4.30 4.40 0.09 -- 4.50 4.60 -- 48 1. VDD = 5.5 Vdc to 4.5 Vdc, VSS = 0 Vdc, TA = -40C to +135C, unless otherwise noted 2. Typical values reflect average measurements at midpoint of voltage range, 25C only. 3. Some disturbance of the ADC accuracy is possible during any injection event and is dependent on board layout and power supply decoupling. 4. Run (operating) IDD measured using internal oscillator at its 32-MHz rate. VDD = 5.5 Vdc. All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. All ports configured as inputs. Measured with all modules enabled. 5. All measurements taken with LVI enabled. 6. Wait IDD measured using internal oscillator at its 1-MHz rate. All inputs 0.2 V from rail; no dc loads; less than 100 pF on all outputs. All ports configured as inputs. 7. Stop IDD is measured with no port pin sourcing current; all modules are disabled. OSCSTOPEN option is not selected. 8. Pullups and pulldowns are disabled. 9. Maximum is highest voltage that power-on reset (POR) is guaranteed. 10. Maximum is highest voltage that POR is possible. 11. These values assume the LVI is operating in 5-V mode (i.e. LVI5OR3 bit is set to 1). For 3-V mode (LVI5OR3 = 0), values become Min: 2.45, Typ: 2.60, Max: 2.80 12. These values assume the LVI is operating in 5-V mode (i.e. LVI5OR3 bit is set to 1). For 3-V mode (LVI5OR3 = 0), values become Min: 2.55, Typ: 2.66, Max: 2.80 13. These values assume the LVI is operating in 5-V mode (i.e. LVI5OR3 bit is set to 1). For 3-V mode (LVI5OR3 = 0), values become Typ: 60 14. PTA0-PTA4 pullup resistors are for interrupts only and are only enabled when the keyboard is in use. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Electrical Specifications Data Sheet 285 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Electrical Specifications 20.6 Control Timing Characteristic(1) Frequency of operation(2) Crystal option (EXTSLOW = 1) Crystal option (EXTSLOW = 0) External clock option(3) Internal operating frequency Internal clock period (1/fOP) Symbol Min Max Unit fosc 32 1 dc(4) -- 125 50 50 Note 8 100 8 32 8 -- -- -- -- -- -- kHz MHz MHz MHz ns ns ns tcyc ns tcyc fop tcyc tIRL tILIH tILIL tTH,tTL tTLTL Freescale Semiconductor, Inc... RESET input pulse width low(5) IRQ interrupt pulse width low(6) (edge-triggered) IRQ interrupt pulse period 16-bit timer(7) Input capture pulse width Input capture period Note 8 1. VSS = 0 Vdc; timing shown with respect to 20% VDD and 70% VSS unless otherwise noted. 2. See Section 8. Internal Clock Generator (ICG) Module for more information. 3. No more than 10% duty cycle deviation from 50% 4. Some modules may require a minimum frequency greater than dc for proper operation. See appropriate table for this information. 5. Minimum pulse width reset is guaranteed to be recognized. It is possible for a smaller pulse width to cause a reset. 6. Minimum pulse width is for guaranteed interrupt. It is possible for a smaller pulse width to be recognized. 7. Minimum pulse width is for guaranteed interrupt. It is possible for a smaller pulse width to be recognized. 8. The minimum period, tILIL or tTLTL, should not be less than the number of cycles it takes to execute the interrupt service routine plus tcyc. Data Sheet 286 Electrical Specifications MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Electrical Specifications Internal Oscillator Characteristics 20.7 Internal Oscillator Characteristics Characteristic(1) Internal oscillator base frequency(2), (3) Internal oscillator tolerance Internal oscillator multiplier(4) Symbol fINTOSC fOSC_TOL N Min 230.4 -25 1 Typ 307.2 -- -- Max 384 +25 127 Unit kHz % -- Freescale Semiconductor, Inc... 1. VDD = 4.5 to 5.5 Vdc, VSS = 0 Vdc, TA = -40C to +135C, unless otherwise noted 2. Internal oscillator is selectable through software for a maximum frequency. Actual frequency will be multiplier (N) x base frequency. 3. fBus = (fINTOSC / 4) x N when internal clock source selected 4. Multiplier must be chosen to limit the maximum bus frequency of 8 MHz for 4.5-V operation. 20.8 External Oscillator Characteristics Characteristic(1) External clock option(2)(3) With ICG clock disabled With ICG clock enabled EXTSLOW = 1(4) EXTSLOW = 0(4) External crystal options(7)(8) EXTSLOW = 1(4) EXTSLOW = 0(4) Crystal load capacitance(9) Crystal fixed capacitance(9) Crystal tuning capacitance(9) Feedback bias resistor(9) Series resistor (9)(10) Symbol Min Typ Max 32 M(6) Hz 60 307.2 k -- -- 307.2 k 32 M(6) Unit dc(5) fEXTOSC -- fEXTOSC CL C1 C2 RB RS 30 k 1M -- -- -- -- -- -- -- -- 2 x CL 2 x CL 10 -- 100 k 8M -- -- -- -- -- Hz pF pF pF M M 1. VDD = 4.5 to 5.5 Vdc, VSS = 0 Vdc, TA = -40C to +135C, unless otherwise noted 2. Setting EXTCLKEN configuration option enables OSC1 pin for external clock square-wave input. 3. No more than 10% duty cycle deviation from 50% 4. EXTSLOW configuration option configures external oscillator for a slow speed crystal and sets the clock monitor circuits of the ICG module to expect an external clock frequency that is higher/lower than the internal oscillator base frequency, fINTOSC. 5. Some modules may require a minimum frequency greater than dc for proper operation. See appropriate table for this information. 6. MCU speed derates from 32 MHz at VDD = 4.5 Vdc 7. Setting EXTCLKEN and EXTXTALEN configuration options enables OSC1 and OSC2 pins for external crystal option. 8. fBus = (fEXTOSC / 4) when external clock source is selected. 9. Consult crystal vendor data sheet, see Figure 8-3. Internal Clock Generator Block Diagram. 10. Not required for high-frequency crystals MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Electrical Specifications Data Sheet 287 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Electrical Specifications 20.9 Trimmed Accuracy of the Internal Clock Generator The unadjusted frequency of the low-frequency base clock (IBASE), when the comparators in the frequency comparator indicate zero error, can vary as much as 25% due to process, temperature, and voltage. The trimming capability exists to compensate for process affects. The remaining variation in frequency is due to temperature, voltage, and change in target frequency (multiply register setting). These affects are designed to be minimal, however variation does occur. Better performance is seen with lower settings of N. 20.9.1 Trimmed Internal Clock Generator Characteristics Freescale Semiconductor, Inc... Characteristic(1) Symbol Min -- -- -- -- -- -- Typ 2.0 2.5 0.05 1.0 1.0 1.0 Max 3.5 5.0 0.08 2.0 2.0 2.0 Unit % %/C Absolute trimmed internal oscillator tolerance(2),(3) Fabs_tol -40C to 85C -40C to 135C Variation over temperature(3), (4) Variation over voltage(3), (5) 25C -40C to 85C -40C to 135C Var_temp Var_volt %/V 1. These specifications concern long-term frequency variation. Each measurement is taken over a 1-ms period. 2. Absolute value of variation in ICG output frequency, trimmed at nominal VDD and temperature, as temperature and VDD are allowed to vary for a single given setting of N. 3. Specification is characterized but not tested. 4. Variation in ICG output frequency for a fixed N and voltage 5. Variation in ICG output frequency for a fixed N Data Sheet 288 Electrical Specifications MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Electrical Specifications Analog-to-Digital Converter (ADC) Characteristics 20.10 Analog-to-Digital Converter (ADC) Characteristics Characteristic Supply voltage Input voltages Resolution Absolute accuracy ADC internal clock Symbol VDDA VADIN BAD AAD fADIC RAD tADPU tADC tADS MAD ZADI FADI CADI IVREF AAD ZADI FADI -- 000 3FC -- -- -1 00 FE -- -- -- -- 1.6 -- -- -- -- 003 3FF 30 -- +1 01 FF +7/8 -1/8 Min 4.5 0 10 -4 500 k VSSA 16 16 5 Typ -- -- -- -- -- -- -- -- -- Max 5.5 VDDA 10 +4 1.048 M VDDA -- 17 -- Unit V V Bits LSB Hz V tAIC cycles tAIC cycles tAIC cycles Guaranteed Hex Hex pF mA LSB Hex Hex LSB Includes quantization Not tested Includes quantization tAIC = 1/fADIC Notes VDDA should be tied to the same potential as VDD via separate traces VADIN <= VDDA Freescale Semiconductor, Inc... Conversion range Power-up time Conversion time Sample time Monotonicity Zero input reading Full-scale reading Input capacitance VREFH/VREFL current Absolute accuracy (8-bit truncated mode) Zero input reading (8-bit truncated mode) Full-scale reading (8-bit truncated mode) Quantization error (8-bit truncated mode) MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Electrical Specifications Data Sheet 289 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Electrical Specifications 20.11 SPI Characteristics Diagram Number(1) Characteristic(2) Operating frequency Master Slave Cycle time Master Slave Enable lead time Enable lag time Clock (SPSCK) high time Master Slave Clock (SPSCK) low time Master Slave Data setup time (inputs) Master Slave Data hold time (inputs) Master Slave Access time, slave(3) CPHA = 0 CPHA = 1 Disable time, slave(4) Data valid time, after enable edge Master Slave(5) Data hold time, outputs, after enable edge Master Slave Symbol Min Max Unit fOP(M) fOP(S) tCYC(M) tCYC(S) tLead(S) tLag(S) tSCKH(M) tSCKH(S) tSCKL(M) tSCKL(S) tSU(M) tSU(S) tH(M) tH(S) tA(CP0) tA(CP1) tDIS(S) tV(M) tV(S) tHO(M) tHO(S) fOP/128 DC 2 1 1 1 tcyc -25 1/2 tcyc -25 tcyc -25 1/2 tcyc -25 30 30 fOP/2 fOP 128 -- -- -- 64 tcyc -- 64 tcyc -- -- -- MHz MHz tcyc tcyc tcyc tcyc ns ns 1 2 Freescale Semiconductor, Inc... 3 4 5 ns ns 6 ns ns 7 30 30 -- -- ns ns 8 0 0 -- 40 40 40 ns ns ns 9 10 -- -- 50 50 ns ns 11 0 0 -- -- ns ns 1. Numbers refer to dimensions in Figure 20-1 and Figure 20-2. 2. All timing is shown with respect to 20% VDD and 70% VDD, unless noted; 100 pF load on all SPI pins. 3. Time to data active from high-impedance state 4. Hold time to high-impedance state 5. With 100 pF on all SPI pins Data Sheet 290 Electrical Specifications MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Electrical Specifications SPI Characteristics SS INPUT SS PIN OF MASTER HELD HIGH 1 SPSCK OUTPUT CPOL = 0 NOTE 5 4 SPSCK OUTPUT CPOL = 1 NOTE 5 4 6 7 LSB IN 10 BITS 6-1 11 MASTER LSB OUT MISO INPUT MSB IN 11 BITS 6-1 Freescale Semiconductor, Inc... MOSI OUTPUT MASTER MSB OUT Note: This first clock edge is generated internally, but is not seen at the SPSCK pin. a) SPI Master Timing (CPHA = 0) SS INPUT SS PIN OF MASTER HELD HIGH 1 SPSCK OUTPUT CPOL = 0 5 4 NOTE SPSCK OUTPUT CPOL = 1 5 4 6 7 LSB IN 10 BITS 6-1 MASTER LSB OUT NOTE MISO INPUT 10 MOSI OUTPUT MSB IN 11 MASTER MSB OUT BITS 6-1 Note: This last clock edge is generated internally, but is not seen at the SPSCK pin. b) SPI Master Timing (CPHA = 1) Figure 20-1. SPI Master Timing MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Electrical Specifications Data Sheet 291 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Electrical Specifications SS INPUT 1 SPSCK INPUT CPOL = 0 2 SPSCK INPUT CPOL = 1 8 MISO INPUT SLAVE 6 MOSI OUTPUT MSB IN MSB OUT 7 10 BITS 6-1 BITS 6-1 11 LSB IN SLAVE LSB OUT 11 5 4 9 NOTE 5 4 3 Freescale Semiconductor, Inc... Note: Not defined but normally MSB of character just received a) SPI Slave Timing (CPHA = 0) SS INPUT 1 SPSCK INPUT CPOL = 0 2 SPSCK INPUT CPOL = 1 8 MISO OUTPUT 5 4 10 NOTE SLAVE 6 MOSI INPUT MSB IN MSB OUT 7 10 BITS 6-1 BITS 6-1 11 LSB IN 9 SLAVE LSB OUT 5 4 3 Note: Not defined but normally LSB of character previously transmitted b) SPI Slave Timing (CPHA = 1) Figure 20-2. SPI Slave Timing Data Sheet 292 Electrical Specifications MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Electrical Specifications Memory Characteristics 20.12 Memory Characteristics Characteristic RAM data retention voltage FLASH program bus clock frequency FLASH read bus clock frequency FLASH page erase time <1 K cycles >1 K cycles Symbol VRDR -- fRead(1) tErase tMErase tNVS tNVH tNVHL tPGS tPROG tRCV(2) tHV(3) -- -- Min 1.3 1 0 0.9 3.6 4 10 5 100 5 30 1 -- 10 k 15 Typ -- -- -- 1 4 -- -- -- -- -- -- -- -- 100 k 100 Max -- -- 8M 1.1 5.5 -- -- -- -- -- 40 -- 4 -- -- Unit V MHz Hz ms ms s s s s s s ms Cycles Years Freescale Semiconductor, Inc... FLASH mass erase time FLASH PGM/ERASE to HVEN setup time FLASH high-voltage hold time FLASH high-voltage hold time (mass erase) FLASH program hold time FLASH program time FLASH return to read time FLASH cumulative program hv period FLASH endurance(4) FLASH data retention time(5) 1. fRead is defined as the frequency range for which the FLASH memory can be read. 2. tRCV is defined as the time it needs before the FLASH can be read after turning off the high voltage charge pump, by clearing HVEN to 0. 3. tHV is defined as the cumulative high voltage programming time to the same row before next erase. tHV must satisfy this condition: tNVS + tNVH + tPGS + (tPROG x 64) tHV maximum. 4. Typical endurance was evaluated for this product family. For additional information on how Motorola defines Typical Endurance, please refer to Engineering Bulletin EB619. 5. Typical data retention values are based on intrinsic capability of the technology measured at high temperature and de-rated to 25C using the Arrhenius equation. For additional information on how Motorola defines Typical Data Retention, please refer to Engineering Bulletin EB618. 6. In the 125C to 135C temperature range, the FLASH is guaranteed as read only. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Electrical Specifications Data Sheet 293 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Electrical Specifications Freescale Semiconductor, Inc... Data Sheet 294 Electrical Specifications MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Section 21. Ordering Information and Mechanical Specifications 21.1 Introduction This section contains ordering numbers for MC68HC908EY16. An example of the device numbering system is given in Figure 21-1. In addition, this section gives the package dimensions for the 32-pin quad flat pack (QFP). Freescale Semiconductor, Inc... 21.2 MC Order Numbers Table 21-1. MC Order Numbers MC Order Number(1) MC68HC908EY16KFA MC68HC908EY16MFA MC68HC908EY16VFA MC68HC908EY16CFA 1. FA = Quad flat pack Operating Temperature Range -40C to +135C -40C to +125C -40C to +105C -40C to +85C MC68HC908EY16XXX FAMILY PACKAGE DESIGNATOR TEMPERATURE RANGE Figure 21-1. Device Numbering System MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Ordering Information and Mechanical Specifications Data Sheet 295 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Ordering Information and Mechanical Specifications 21.3 32-Pin QFP (Case Number 873) L 24 25 17 S S 16 D S C A-B -A- L -B- B 0.05 (0.002) A-B V M 0.20 (0.008) Freescale Semiconductor, Inc... 0.20 (0.008) M H A-B S D B B P DETAIL A 32 1 8 9 -A-, -B-, -D- -D- A 0.20 (0.008) M DETAIL A C A-B S D S 0.05 (0.002) A-B S 0.20 (0.008) M H A-B S D S BASE METAL F M DETAIL C J N D 0.20 (0.008) M CE -C- SEATING PLANE -H- H M DATUM PLANE 0.01 (0.004) C A-B S D S G SECTION B-B VIEW ROTATED 90 _CLOCKWISE U T -H- DATUM PLANE R K X DETAIL C Q NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DATUM PLANE -H- IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4. DATUMS -A-, -B- AND -D- TO BE DETERMINED AT DATUM PLANE -H-. 5. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE -C-. 6. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 (0.010) PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE -H-. 7. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. DIM A B C D E F G H J K L M N P Q R S T U V X MILLIMETERS MIN MAX 6.95 7.10 6.95 7.10 1.40 1.60 0.273 0.373 1.30 1.50 0.273 --- 0.80 BSC --- 0.20 0.119 0.197 0.33 0.57 5.6 REF 6_ 8_ 0.119 0.135 0.40 BSC 5_ 10_ 0.15 0.25 8.85 9.15 0.15 0.25 5_ 11_ 8.85 9.15 1.00 REF INCHES MIN MAX 0.274 0.280 0.274 0.280 0.055 0.063 0.010 0.015 0.051 0.059 0.010 --- 0.031 BSC --- 0.008 0.005 0.008 0.013 0.022 0.220 REF 6_ 8_ 0.005 0.005 0.016 BSC 5_ 10_ 0.006 0.010 0.348 0.360 0.006 0.010 5_ 11_ 0.348 0.360 0.039 REF Data Sheet 296 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 Ordering Information and Mechanical Specifications MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Appendix A. MC68HC908EY8 A.1 Introduction The MC68HC908EY8 is a member of the low-cost, high-performance M68HC08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced M68HC08 central processor unit (CPU08) and are available with a variety of modules, memory sizes and types, and package types. The information contained in this document pertains to the MC68HC908EY8 with the exceptions shown in this appendix. Freescale Semiconductor, Inc... A.2 Block Diagram See Figure A-1. A.3 Memory The memory map, shown in Figure A-2, includes: * 8 Kbytes of FLASH memory, 7680 bytes of user space * 512 bytes of random-access memory (RAM) * 36 bytes of user-defined vectors * 310 bytes of monitor routines in read-only memory (ROM) * 1024 bytes of integrated FLASH burn-in routines in ROM The FLASH memory is an array of 7680 bytes with an additional 36 bytes of user vectors and one byte used for block protection. The FLASH is organized internally as an 8192-word by 8-bit complementary metal-oxide semiconductor (CMOS) page erase, byte (8-bit) program embedded FLASH memory. Each page consists of 64 bytes. The page erase operation erases all words within a page. A page is composed of two adjacent rows. A security feature prevents viewing of the FLASH contents.(1) 1. No security feature is absolutely secure. However, Motorola's strategy is to make reading or copying the FLASH difficult for unauthorized users. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA MC68HC908EY8 Data Sheet 297 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. MC68HC908EY8 INTERNAL BUS M68HC08 CPU CPU REGISTERS ARITHMETIC/LOGIC UNIT (ALU) SINGLE BREAKPOINT BREAK MODULE PORT A DDRA 5-BIT KEYBOARD INTERRUPT MODULE PTA6/SS PTA5/SPSCK PTA4/KBD4 PTA3/KBD3 PTA2/KBD2 PTA1/KBD1 2-CHANNEL TIMER INTERFACE MODULE A PTA0/KBD0 PTB7/AD7/TBCH1 PTB6/AD6/TBCH0 PORT B DDRB PTB5/AD5 PTB4/AD4 PTB3/AD3 PTB2/AD2 PTB1/AD1 PTB0/AD0 PTC4/OSC1 PTC3/OSC2 PTC2/MCLK PTC1/MOSI PTC0/MISO PTD1/TACH1 PTD0/TACH0 PTE1/RxD PTE0/TxD PORT C PORT E PORT D CONTROL AND STATUS REGISTERS 64 BYTES USER FLASH 7680 BYTES USER RAM 384 BYTES MONITOR ROM 310 BYTES FLASH PROGRAMMING (BURN-IN) ROM 1024 BYTES USER FLASH VECTOR SPACE 36 BYTES Freescale Semiconductor, Inc... 2-CHANNEL TIMER INTERFACE MODULE B ENHANCED SERIAL COMMUNICATION INTERFACE MODULE COMPUTER OPERATING PROPERLY MODULE OSC2 OSC1 INTERNAL CLOCK GENERATOR MODULE SERIAL PERIPHERAL INTERFACE MODULE RST 24 INTERNAL SYSTEM INTEGRATION MODULE SINGLE EXTERNAL IRQ MODULE CONFIGURATION REGISTER MODULE PERIODIC WAKEUP TIMEBASE MODULE ARBITER MODULE PRESCALER MODULE IRQ VREFH VDDA VREFL VSSA VDD VSS DDRE DDRD DDRC 10-BIT ANALOG-TO-DIGITAL CONVERTER MODULE POWER-ON RESET MODULE SECURITY MODULE POWER BEMF MODULE Figure A-1. MC68HC908EY8 Block Diagram Data Sheet 298 MC68HC908EY8 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. MC68HC908EY8 $0000 $003F $0040 $01BF $01C00 Unimplemented 3648 Bytes RAM 384 Bytes I/O Registers 64 Bytes $FE08 $FE09 $FE0A $FE0B $FE0C $FE0D $FE0F $FE10 Reserved for Integrated FLASH Burn-in Routines 1024 Bytes $FE1F $FE20 Unimplemented 53,334 Bytes FF55 FF56 FLASH Memory 7680 Bytes SIM Break Status Register (SBSR) SIM Reset Status Register (SRSR) Reserved SIM Break Flag Control Register (SBFCR) RESERVED RESERVED RESERVED Reserved for FLASH Test Control Register (FLTCR) FF7D $FF7E $FF7F $FFDB $FFDC $FFFF FLASH Control Register (FLCR) Break Address Register High (BRKH) Break Address Register Low (BRKL) Break Status and Control Register (BRKSCR) LVI Status Register (LVISR) Reserved 3 Bytes Reserved 16 Bytes Reserved for Compatibility with Monitor Code for A-Family Parts Freescale Semiconductor, Inc... $0FFF $1000 $13FF $1400 $DFFF $E000 $FDFF $FE00 $FE01 $FE02 $FE03 $FE04 $FE05 $FE06 $FE07 Monitor ROM 310 Bytes Unimplemented 40 Bytes FLASH Block Protect Register (FLBPR) Unimplemented 93 Bytes FLASH Vectors 36 Bytes Note: Locations $FFF6-$FFFD are reserved for eight security bytes. Figure A-2. MC68HC908EY8 Memory Map MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA MC68HC908EY8 Data Sheet 299 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. MC68HC908EY8 A.4 MC Order Numbers Table A-1. MC Order Numbers MC Order Number(1) MC68HC908EY8KFA MC68HC908EY8MFA MC68HC908EY8VFA MC68HC908EY8CFA Operating Temperature Range -40C to +135C -40C to +125C -40C to +105C -40C to +85C Freescale Semiconductor, Inc... 1. FA = Quad flat pack MC68HC908EY8 XXX FAMILY PACKAGE DESIGNATOR TEMPERATURE RANGE Figure A-3. Device Numbering System Data Sheet 300 MC68HC908EY8 MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Glossary A -- See "accumulator (A)." accumulator (A) -- An 8-bit general-purpose register in the CPU08. The CPU08 uses the accumulator to hold operands and results of arithmetic and logic operations. Freescale Semiconductor, Inc... acquisition mode -- A mode of PLL operation during startup before the PLL locks on a frequency. Also see "tracking mode." address bus -- The set of wires that the CPU or DMA uses to read and write memory locations. addressing mode -- The way that the CPU determines the operand address for an instruction. The M68HC08 CPU has 16 addressing modes. ALU -- See "arithmetic logic unit (ALU)." arithmetic logic unit (ALU) -- The portion of the CPU that contains the logic circuitry to perform arithmetic, logic, and manipulation operations on operands. asynchronous -- Refers to logic circuits and operations that are not synchronized by a common reference signal. baud rate -- The total number of bits transmitted per unit of time. BCD -- See "binary-coded decimal (BCD)." binary -- Relating to the base 2 number system. binary number system -- The base 2 number system, having two digits, 0 and 1. Binary arithmetic is convenient in digital circuit design because digital circuits have two permissible voltage levels, low and high. The binary digits 0 and 1 can be interpreted to correspond to the two digital voltage levels. binary-coded decimal (BCD) -- A notation that uses 4-bit binary numbers to represent the 10 decimal digits and that retains the same positional structure of a decimal number. For example, 234 (decimal) = 0010 0011 0100 (BCD) bit -- A binary digit. A bit has a value of either 0 or 1. branch instruction -- An instruction that causes the CPU to continue processing at a memory location other than the next sequential address. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Glossary Data Sheet 301 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Glossary break module -- A module in the M68HC08 Family. The break module allows software to halt program execution at a programmable point in order to enter a background routine. breakpoint -- A number written into the break address registers of the break module. When a number appears on the internal address bus that is the same as the number in the break address registers, the CPU executes the software interrupt instruction (SWI). break interrupt -- A software interrupt caused by the appearance on the internal address bus of the same value that is written in the break address registers. Freescale Semiconductor, Inc... bus -- A set of wires that transfers logic signals. bus clock -- The bus clock is derived from the CGMOUT output from the CGM. The bus clock frequency, fop, is equal to the frequency of the oscillator output, CGMXCLK, divided by four. byte -- A set of eight bits. C -- The carry/borrow bit in the condition code register. The CPU08 sets the carry/borrow bit when an addition operation produces a carry out of bit 7 of the accumulator or when a subtraction operation requires a borrow. Some logical operations and data manipulation instructions also clear or set the carry/borrow bit (as in bit test and branch instructions and shifts and rotates). CCR -- See "condition code register." central processor unit (CPU) -- The primary functioning unit of any computer system. The CPU controls the execution of instructions. CGM -- See "clock generator module (CGM)." clear -- To change a bit from 1 to 0; the opposite of set. clock -- A square wave signal used to synchronize events in a computer. clock generator module (CGM) -- A module in the M68HC08 Family. The CGM generates a base clock signal from which the system clocks are derived. The CGM may include a crystal oscillator circuit and or phase-locked loop (PLL) circuit. comparator -- A device that compares the magnitude of two inputs. A digital comparator defines the equality or relative differences between two binary numbers. computer operating properly module (COP) -- A counter module in the M68HC08 Family that resets the MCU if allowed to overflow. Data Sheet 302 Glossary MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Glossary condition code register (CCR) -- An 8-bit register in the CPU08 that contains the interrupt mask bit and five bits that indicate the results of the instruction just executed. control bit -- One bit of a register manipulated by software to control the operation of the module. control unit -- One of two major units of the CPU. The control unit contains logic functions that synchronize the machine and direct various operations. The control unit decodes instructions and generates the internal control signals that perform the requested operations. The outputs of the control unit drive the execution unit, which contains the arithmetic logic unit (ALU), CPU registers, and bus interface. COP -- See "computer operating properly module (COP)." counter clock -- The input clock to the TIM counter. This clock is the output of the TIM prescaler. CPU -- See "central processor unit (CPU)." CPU08 -- The central processor unit of the M68HC08 Family. CPU clock -- The CPU clock is derived from the CGMOUT output from the CGM. The CPU clock frequency is equal to the frequency of the oscillator output, CGMXCLK, divided by four. CPU cycles -- A CPU cycle is one period of the internal bus clock, normally derived by dividing a crystal oscillator source by two or more so the high and low times will be equal. The length of time required to execute an instruction is measured in CPU clock cycles. CPU registers -- Memory locations that are wired directly into the CPU logic instead of being part of the addressable memory map. The CPU always has direct access to the information in these registers. The CPU registers in an M68HC08 are: * A (8-bit accumulator) * H:X (16-bit index register) * SP (16-bit stack pointer) * PC (16-bit program counter) * CCR (condition code register containing the V, H, I, N, Z, and C bits) CSIC -- customer-specified integrated circuit cycle time -- The period of the operating frequency: tCYC = 1/fOP. decimal number system -- Base 10 numbering system that uses the digits zero through nine. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Glossary Data Sheet 303 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Glossary direct memory access module (DMA) -- A M68HC08 Family module that can perform data transfers between any two CPU-addressable locations without CPU intervention. For transmitting or receiving blocks of data to or from peripherals, DMA transfers are faster and more code-efficient than CPU interrupts. DMA -- See "direct memory access module (DMA)." DMA service request -- A signal from a peripheral to the DMA module that enables the DMA module to transfer data. duty cycle -- A ratio of the amount of time the signal is on versus the time it is off. Duty cycle is usually represented by a percentage. EEPROM -- Electrically erasable, programmable, read-only memory. A nonvolatile type of memory that can be electrically reprogrammed. EPROM -- Erasable, programmable, read-only memory. A nonvolatile type of memory that can be erased by exposure to an ultraviolet light source and then reprogrammed. exception -- An event such as an interrupt or a reset that stops the sequential execution of the instructions in the main program. external interrupt module (IRQ) -- A module in the M68HC08 Family with both dedicated external interrupt pins and port pins that can be enabled as interrupt pins. fetch -- To copy data from a memory location into the accumulator. firmware -- Instructions and data programmed into nonvolatile memory. free-running counter -- A device that counts from zero to a predetermined number, then rolls over to zero and begins counting again. full-duplex transmission -- Communication on a channel in which data can be sent and received simultaneously. H -- The upper byte of the 16-bit index register (H:X) in the CPU08. H -- The half-carry bit in the condition code register of the CPU08. This bit indicates a carry from the low-order four bits of the accumulator value to the high-order four bits. The half-carry bit is required for binary-coded decimal arithmetic operations. The decimal adjust accumulator (DAA) instruction uses the state of the H and C bits to determine the appropriate correction factor. hexadecimal -- Base 16 numbering system that uses the digits 0 through 9 and the letters A through F. high byte -- The most significant eight bits of a word. illegal address -- An address not within the memory map Data Sheet 304 Glossary MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Freescale Semiconductor, Inc... For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Glossary illegal opcode -- A nonexistent opcode. I -- The interrupt mask bit in the condition code register of the CPU08. When I is set, all interrupts are disabled. index register (H:X) -- A 16-bit register in the CPU08. The upper byte of H:X is called H. The lower byte is called X. In the indexed addressing modes, the CPU uses the contents of H:X to determine the effective address of the operand. H:X can also serve as a temporary data storage location. input/output (I/O) -- Input/output interfaces between a computer system and the external world. A CPU reads an input to sense the level of an external signal and writes to an output to change the level on an external signal. instructions -- Operations that a CPU can perform. Instructions are expressed by programmers as assembly language mnemonics. A CPU interprets an opcode and its associated operand(s) and instruction. interrupt -- A temporary break in the sequential execution of a program to respond to signals from peripheral devices by executing a subroutine. interrupt request -- A signal from a peripheral to the CPU intended to cause the CPU to execute a subroutine. I/O -- See "input/output (I/0)." IRQ -- See "external interrupt module (IRQ)." jitter -- Short-term signal instability. latch -- A circuit that retains the voltage level (logic 1 or logic 0) written to it for as long as power is applied to the circuit. latency -- The time lag between instruction completion and data movement. least significant bit (LSB) -- The rightmost digit of a binary number. logic 1 -- A voltage level approximately equal to the input power voltage (VDD). logic 0 -- A voltage level approximately equal to the ground voltage (VSS). low byte -- The least significant eight bits of a word. low voltage inhibit module (LVI) -- A module in the M68HC08 Family that monitors power supply voltage. LVI -- See "low voltage inhibit module (LVI)." M68HC08 -- A Motorola family of 8-bit MCUs. mark/space -- The logic 1/logic 0 convention used in formatting data in serial communication. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Glossary Data Sheet 305 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Glossary mask -- 1. A logic circuit that forces a bit or group of bits to a desired state. 2. A photomask used in integrated circuit fabrication to transfer an image onto silicon. mask option -- A optional microcontroller feature that the customer chooses to enable or disable. mask option register (MOR) -- An EPROM location containing bits that enable or disable certain MCU features. MCU -- Microcontroller unit. See "microcontroller." Freescale Semiconductor, Inc... memory location -- Each M68HC08 memory location holds one byte of data and has a unique address. To store information in a memory location, the CPU places the address of the location on the address bus, the data information on the data bus, and asserts the write signal. To read information from a memory location, the CPU places the address of the location on the address bus and asserts the read signal. In response to the read signal, the selected memory location places its data onto the data bus. memory map -- A pictorial representation of all memory locations in a computer system. microcontroller -- Microcontroller unit (MCU). A complete computer system, including a CPU, memory, a clock oscillator, and input/output (I/O) on a single integrated circuit. modulo counter -- A counter that can be programmed to count to any number from zero to its maximum possible modulus. monitor ROM -- A section of ROM that can execute commands from a host computer for testing purposes. MOR -- See "mask option register (MOR)." most significant bit (MSB) -- The leftmost digit of a binary number. multiplexer -- A device that can select one of a number of inputs and pass the logic level of that input on to the output. N -- The negative bit in the condition code register of the CPU08. The CPU sets the negative bit when an arithmetic operation, logical operation, or data manipulation produces a negative result. nibble -- A set of four bits (half of a byte). object code -- The output from an assembler or compiler that is itself executable machine code, or is suitable for processing to produce executable machine code. opcode -- A binary code that instructs the CPU to perform an operation. Data Sheet 306 Glossary MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Glossary open-drain -- An output that has no pullup transistor. An external pullup device can be connected to the power supply to provide the logic 1 output voltage. operand -- Data on which an operation is performed. Usually a statement consists of an operator and an operand. For example, the operator may be an add instruction, and the operand may be the quantity to be added. oscillator -- A circuit that produces a constant frequency square wave that is used by the computer as a timing and sequencing reference. OTPROM -- One-time programmable read-only memory. A nonvolatile type of memory that cannot be reprogrammed. Freescale Semiconductor, Inc... overflow -- A quantity that is too large to be contained in one byte or one word. page zero -- The first 256 bytes of memory (addresses $0000-$00FF). parity -- An error-checking scheme that counts the number of logic 1s in each byte transmitted. In a system that uses odd parity, every byte is expected to have an odd number of logic 1s. In an even parity system, every byte should have an even number of logic 1s. In the transmitter, a parity generator appends an extra bit to each byte to make the number of logic 1s odd for odd parity or even for even parity. A parity checker in the receiver counts the number of logic 1s in each byte. The parity checker generates an error signal if it finds a byte with an incorrect number of logic 1s. PC -- See "program counter (PC)." peripheral -- A circuit not under direct CPU control. phase-locked loop (PLL) -- A oscillator circuit in which the frequency of the oscillator is synchronized to a reference signal. PLL -- See "phase-locked loop (PLL)." pointer -- Pointer register. An index register is sometimes called a pointer register because its contents are used in the calculation of the address of an operand, and therefore points to the operand. polarity -- The two opposite logic levels, logic 1 and logic 0, which correspond to two different voltage levels, VDD and VSS. polling -- Periodically reading a status bit to monitor the condition of a peripheral device. port -- A set of wires for communicating with off-chip devices. prescaler -- A circuit that generates an output signal related to the input signal by a fractional scale factor such as 1/2, 1/8, 1/10 etc. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Glossary Data Sheet 307 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Glossary program -- A set of computer instructions that cause a computer to perform a desired operation or operations. program counter (PC) -- A 16-bit register in the CPU08. The PC register holds the address of the next instruction or operand that the CPU will use. pull -- An instruction that copies into the accumulator the contents of a stack RAM location. The stack RAM address is in the stack pointer. pullup -- A transistor in the output of a logic gate that connects the output to the logic 1 voltage of the power supply. Freescale Semiconductor, Inc... pulse-width -- The amount of time a signal is on as opposed to being in its off state. pulse-width modulation (PWM) -- Controlled variation (modulation) of the pulse width of a signal with a constant frequency. push -- An instruction that copies the contents of the accumulator to the stack RAM. The stack RAM address is in the stack pointer. PWM period -- The time required for one complete cycle of a PWM waveform. RAM -- Random access memory. All RAM locations can be read or written by the CPU. The contents of a RAM memory location remain valid until the CPU writes a different value or until power is turned off. RC circuit -- A circuit consisting of capacitors and resistors having a defined time constant. read -- To copy the contents of a memory location to the accumulator. register -- A circuit that stores a group of bits. reserved memory location -- A memory location that is used only in special factory test modes. Writing to a reserved location has no effect. Reading a reserved location returns an unpredictable value. reset -- To force a device to a known condition. ROM -- Read-only memory. A type of memory that can be read but cannot be changed (written). The contents of ROM must be specified before manufacturing the MCU. SCI -- See "serial communication interface module (SCI)." serial -- Pertaining to sequential transmission over a single line. serial communications interface module (SCI) -- A module in the M68HC08 Family that supports asynchronous communication. Data Sheet 308 Glossary MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Glossary serial peripheral interface module (SPI) -- A module in the M68HC08 Family that supports synchronous communication. set -- To change a bit from logic 0 to logic 1; opposite of clear. shift register -- A chain of circuits that can retain the logic levels (logic 1 or logic 0) written to them and that can shift the logic levels to the right or left through adjacent circuits in the chain. signed -- A binary number notation that accommodates both positive and negative numbers. The most significant bit is used to indicate whether the number is positive or negative, normally logic 0 for positive and logic 1 for negative. The other seven bits indicate the magnitude of the number. software -- Instructions and data that control the operation of a microcontroller. software interrupt (SWI) -- An instruction that causes an interrupt and its associated vector fetch. SPI -- See "serial peripheral interface module (SPI)." stack -- A portion of RAM reserved for storage of CPU register contents and subroutine return addresses. stack pointer (SP) -- A 16-bit register in the CPU08 containing the address of the next available storage location on the stack. start bit -- A bit that signals the beginning of an asynchronous serial transmission. status bit -- A register bit that indicates the condition of a device. stop bit -- A bit that signals the end of an asynchronous serial transmission. subroutine -- A sequence of instructions to be used more than once in the course of a program. The last instruction in a subroutine is a return from subroutine (RTS) instruction. At each place in the main program where the subroutine instructions are needed, a jump or branch to subroutine (JSR or BSR) instruction is used to call the subroutine. The CPU leaves the flow of the main program to execute the instructions in the subroutine. When the RTS instruction is executed, the CPU returns to the main program where it left off. synchronous -- Refers to logic circuits and operations that are synchronized by a common reference signal. TIM -- See "timer interface module (TIM)." timer interface module (TIM) -- A module used to relate events in a system to a point in time. timer -- A module used to relate events in a system to a point in time. Freescale Semiconductor, Inc... MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Glossary Data Sheet 309 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Glossary toggle -- To change the state of an output from a logic 0 to a logic 1 or from a logic 1 to a logic 0. tracking mode -- Mode of low-jitter PLL operation during which the PLL is locked on a frequency. Also see "acquisition mode." two's complement -- A means of performing binary subtraction using addition techniques. The most significant bit of a two's complement number indicates the sign of the number (1 indicates negative). The two's complement negative of a number is obtained by inverting each bit in the number and then adding 1 to the result. Freescale Semiconductor, Inc... unbuffered -- Utilizes only one register for data; new data overwrites current data. unimplemented memory location -- A memory location that is not used. Writing to an unimplemented location has no effect. Reading an unimplemented location returns an unpredictable value. Executing an opcode at an unimplemented location causes an illegal address reset. V --The overflow bit in the condition code register of the CPU08. The CPU08 sets the V bit when a two's complement overflow occurs. The signed branch instructions BGT, BGE, BLE, and BLT use the overflow bit. variable -- A value that changes during the course of program execution. VCO -- See "voltage-controlled oscillator." vector -- A memory location that contains the address of the beginning of a subroutine written to service an interrupt or reset. voltage-controlled oscillator (VCO) -- A circuit that produces an oscillating output signal of a frequency that is controlled by a dc voltage applied to a control input. waveform -- A graphical representation in which the amplitude of a wave is plotted against time. wired-OR -- Connection of circuit outputs so that if any output is high, the connection point is high. word -- A set of two bytes (16 bits). write -- The transfer of a byte of data from the CPU to a memory location. X -- The lower byte of the index register (H:X) in the CPU08. Z -- The zero bit in the condition code register of the CPU08. The CPU08 sets the zero bit when an arithmetic operation, logical operation, or data manipulation produces a result of $00. Data Sheet 310 Glossary MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Data Sheet -- MC68HC908EY16 Revision History Changes from Rev 6.0 published in January 2004 to Rev 7.0 published in May 2004 Section General Description Page (in Rev 7.0) 19 35 37 50 Description of change Changed "25 percent accuracy with trim capability to 2 percent" to "25 percent accuracy with a trimming capability of better than 1 percent" (two instances). Changed "BRKSCR" to "BSCR". Added sentence about 125C to 135C temperature range. Changed "ms" to "s" (two instances). Freescale Semiconductor, Inc... Memory Memory Analog-to-Digital Converter (ADC) Module Computer Operating Properly (COP) Module Internal Clock Generator (ICG) Module Internal Clock Generator (ICG) Module Input/Output (I/O) Ports (PORTS) Enhanced Serial Communications Interface (ESCI) Module Timer Interface A (TIMA) Module Development Support Electrical Specifications Electrical Specifications Electrical Specifications Ordering Information and Mechanical Specifications Appendix A. MC68HC908EY8 72 Changed "COPRS = 1" to "COPRS = 0". 89 Changed "7 percent" to "3.5 percent" (two instances). 116 Replaced "to +/-2%" with a cross-reference. 141 Added note. 177 Modified note to include reference to Prescaler Divisor Fine Adjust (PDFA). 244 265 on 284 on 286 288 Deleted "port B or". Whole section on Development Support replaced. Changed "125C" to "135C" on pages 282, 283 (3), 285 (2), 286 (2). Added note 6 on page 291. Modified the first row of the table to show two crystal options, instead of one.. Modified the typical and maximum values in the first row of the table. 295 Appended row to Table 21-1. 297 Appended row to Table A-1. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Revision History Data Sheet 311 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Revision History Section Appendix A. MC68HC908EY8 Page (in Rev 7.0) 298, 299 Description of change Change RAM size from 512 to 384 and adjusted addresses accordingly. Changes from Rev 5.0 published in September 2003 to Rev 6.0 published in January 2004 Section Memory Appendix A. MC68HC908EY8 Page (in Rev 6.0) 40 Description of change Removed erroneous Caution note to 2.6.3 FLASH Mass Erase Operation Updated 2.6.5 FLASH Block Protection and 2.6.6 FLASH Block Protect Register Added appendix describing the MC68HC908EY8 295 Freescale Semiconductor, Inc... Changes from Rev 4.0 published in February 2003 to Rev 5.0 published in September 2003 Section Throughout Memory Computer Operating Properly (COP) Module System Integration Module (SIM) Development Support Electrical Specifications Page (in Rev 5.0) N/A 39 40 69 Description of change Reformatted document to current publications standards Updated procedures for FLASH page erase operation Updated procedures for FLASH mass erase operation Updated block diagram 196 263 289 Updated definition for SBSW bit of SIM break status register (SBSR) Updated definition for SBSW bit of SIM break status register (SBSR) Updated memory characteristics table with new information Corrected notes to supply currents in 20.5 DC Electrical Characteristics. Changes from Rev 3.0 published in November 2002 to Rev 4.0 published in February 2003 Section Page (in Rev 4.0) 280 Electrical Specifications 281 285 Description of change Updated parameters for output high voltage (VOH), output low voltage (VOL) and supply current (IDD) Updated parameters for low voltage inhibit reset: VTRIPF, VTRIPR and VHYS. Updated parameters for ADC absolute accuracy, zero input reading, full-scale reading, zero input reading (8-bit truncated mode) and full-scale reading (8-bit truncated mode). Changes from Rev 2.0 published in May 2002 to Rev 3.0 published in November 2002 Section Memory Map FLASH Memory Page (in Rev 3.0) 50 56 62 ESCI vectors re-ordered Minimum changed to 4ms in step 6. Description of change LVI5OR3 bit added to CONFIG1 Data Sheet 312 Revision History MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Revision History Section System Integration Module (SIM) Internal Clock Generator (ICG) Module Configuration Registers (CONFIG1 & CONFIG2) Break Module (BRK) Page (in Rev 3.0) 93 94 106 118 137 151 148 152 162 178 179 180 181 Description of change Figure 6-5 updated Figure 6-6 updated Code example removed from SBSW description PTB6/OSC1 and PTB7/OSC2 corrected to PTC4/OSC1 and PTC3/OSC2 respectively COPD corrected to COPRS in COPRS bit description LVI5OR3 bit added to CONFIG1 and default reset state changed to 0 LVI5OR3 description added Code example removed from SBSW description COPL corrected to COPRS in Figure 11-1 COPL corrected to COPRS in top paragraph COPL corrected to COPRS in Section 11.4.8 IRQ1 corrected to IRQ 3rd bullet added to features IRQ1 corrected to IRQ Extra paragraph added describing LINR bit functionality in LIN version 1.2 systems `SCI clock source' changed to `Frequency of the SCI clock source' in baud rate equation and description Output high voltage, ILOAD=-10.0mA changed to -5.0mA Output low voltage, ILOAD=10.0mA changed to 5.0mA Footnotes 11, 12 and 13 added Freescale Semiconductor, Inc... Computer Operating Properly (COP) Module Low-Voltage Inhibit (LVI) Module External Interrupt (IRQ) Enhanced Serial Communications Interface (ESCI) Module Electrical Specifications 183 190 191 233 237 382 383 Changes from Rev 1.0 published on 17 April 2002 to Rev 2.0 published in May 2002 3V option removed. PTB5 frequency divider function removed. BEMF section moved from appendix to Section 18 . Section Memory Map Configuration Registers (CONFIG1 & CONFIG2) Enhanced Serial Communications Interface (ESCI) Module Page (in Rev 2.0) 50 148 Description of change ESCIBDSRC bit added to CONFIG2 ESCIBDSRC bit added to CONFIG2 with bit description 200 Baud rate selection sentence added to sections 14.5 and 14.5.2 and after Table 14-10. Changes from Rev 0.4 published internally on 9 April 2002 to Rev 1.0 published on 17 April 2002 Change in revision number only to denote external release version. MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Revision History Data Sheet 313 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Revision History Changes from Rev 0.3 published on 6 September 2001 to Rev 0.4 published internally on 9 April 2002 Section Memory Map FLASH Memory System Integration Module (SIM) Configuration Registers (CONFIG1 & CONFIG2) Page (in Rev 0.4) 43 62 65 92 Description of change Reserved port register bits redefined as unimplemented Note added about erasing last FLASH page Removed last two sentences of FLASH Block Protection description RST description added 149 169 PTB7 changed to PTC3 Table 10-1. Mode Selection added Added sentence about forced monitor mode Updated first note in section 10.5.1 PTB5 column added to Table 10-2 PTB5 pin added to Figure 10-1 Note added regarding length of break character when followed by an idle. Prescale bits renamed ACLK = 0 description changed Several updates for clarification Several updates for clarification Reserved register bits redefined as unimplemented Table 20-1 updated to show all unused combinations Left Justified Mode description corrected Reserved register bits redefined as unimplemented Port B description updated Changes to: Hi-Z leakage current Input current Monitor mode entry voltage External clock frequency of operation FLASH page erase time Freescale Semiconductor, Inc... Monitor ROM (MON) 170 170 171 Enhanced Serial Communications Interface (ESCI) Module Timer Interface A (TIMA) Module Timer Interface B (TIMB) Module Analog-to-Digital Converter (ADC) Module Input/Output (I/O) Ports 210 238 243 and 244 279 - 301 303 - 326 345 354 355 361 - 376 366 382 and 384 382 and 384 382 and 384 386 391 Preliminary Electrical Specifications Changes from Rev 0.2 published on 1 August 2001 to Rev 0.3 published on 6 September 2001 Section Memory Map Configuration Registers (CONFIG1 & CONFIG2) Page (in Rev 0.3) 50 150 152 Description of change $001E TMBCLKSEL and SSBPUENB bits added $001E TMBCLKSEL and SSBPUENB bits added Corrections to Table 8-1: PTB6 to PTC4 and PTB7 to PTC3 Data Sheet 314 Revision History MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Revision History Section Page (in Rev 0.3) 188 189 190 191 Description of change Figure 12-1 updated, digital filter removed False reset protection text updated Table 12-1 updated References to digital filter removed External clock input removed from features External clock input removed from features Divide-by-128 replaced by divide-by-1024 Figure 19-1 updated Note added after Table 19-1 PTC and Cx removed from Figure 20-1 ADCR changed to ADCLK Control Timing specifications added SPI characteristics added Low-Voltage Inhibit (LVI) Module Timer Interface A (TIMA) Module Timer Interface B (TIMB) Module Timebase Module (TBM) Analog-to-Digital Converter (ADC) Module Preliminary Electrical Specifications 280 304 336 Freescale Semiconductor, Inc... 337 338 345 347 384 and 386 388 and 392 391 FLASH read bus clock frequency changed to 8 MHz MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA Revision History Data Sheet 315 For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Revision History Changes from Rev 0.0 published on 17 July 2001 to Rev 0.2 published on 1 August 2001 Section General Description Page (in Rev 0.2) 34 37 48 Description of change Third bullet in standard features list changes to: 8-MHz internal bus frequency at 5V, 4MHZ at 3V BEMF module added to block diagram BEMF register added Register addresses changed for ADC: $003B is now reserved ADSCR is now $003C ADRH is now $003D ADRL is now $003E Reset value of $003F corrected to $04 Several corrections made to Table 4-1 Erased Flash locations corrected to $FF Keyboard interrupt vector corrected to $FFE4 and $FFE5 Address of ADSCR is now $003C Address of ADRH is now $003D Register description now includes left justified mode Address of ADRL is now $003E for right justified mode as well as 8-bit mode Register description now includes left justified mode Reset value of $003F corrected to $04 BEMF register added to Figure 21-1 dc injection current specifications corrected New appendix Memory Map 53 Freescale Semiconductor, Inc... 54 FLASH Memory Monitor ROM (MON) Keyboard Interrupt (KBD) Module 68 168, 172 330 352 Analog-to-Digital Converter (ADC) Module 355 358 359 Input/Output (I/O) Ports Preliminary Electrical Specifications BEMF Module 361 383 401 Data Sheet 316 Revision History MC68HC908EY16 * MC68HC908EY8 -- Rev. 7.0 MOTOROLA For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. Freescale Semiconductor, Inc... For More Information On This Product, Go to: www.freescale.com Freescale Semiconductor, Inc. HOW TO REACH US: USA/EUROPE/LOCATIONS NOT LISTED: Motorola Literature Distribution P.O. Box 5405 Denver, Colorado 80217 1-800-521-6274 or 480-768-2130 JAPAN: Motorola Japan Ltd. SPS, Technical Information Center 3-20-1, Minami-Azabu, Minato-ku Tokyo 106-8573, Japan 81-3-3440-3569 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd. Silicon Harbour Centre 2 Dai King Street Tai Po Industrial Estate Tai Po, N.T., Hong Kong 852-26668334 HOME PAGE: http://motorola.com/semiconductors Freescale Semiconductor, Inc... Information in this document is provided solely to enable system and software implementers to use Motorola products. There are no express or implied copyright licenses granted hereunder to design or fabricate any integrated circuits or integrated circuits based on the information in this document. Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals", must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. MOTOROLA and the Stylized M Logo are registered in the US Patent and Trademark Office. All other product or service names are the property of their respective owners. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. (c) Motorola Inc. 2004 For More Information On This Product, Go to: www.freescale.com MC68HC908EY16/D Rev. 7 3/2004 This datasheet has been download from: www..com Datasheets for electronics components. |
Price & Availability of 68HC908EY16
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |